31 resultater (0,21502 sekunder)

Vis alle filtre

Mærke

Butik

Pris (EUR)

Nulstil filter

Produkter
Fra
Butikker

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm White

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm White

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Grey

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Black

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Black

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Grey

Swivel bends are used to create a tight radius 90 degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.91
1

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm White

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm White

Swivel bends are used to create a tight radius 90 degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.91
1

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm White

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm White

Swept bends are used to create a 92.5 degree change of direction in a waste pipe system. They have a longer radius than knuckle bends and the 92.5 degree angle promotes a self-cleansing flow.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Reducer - 40mm x 32mm Black

FloPlast Push Fit Waste Reducer - 40mm x 32mm Black

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe.It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Black

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Black

Swept bends are used to create a 92.5 degree change of direction in a waste pipe system. They have a longer radius than knuckle bends and the 92.5 degree angle promotes a self-cleansing flow.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Grey

Swept bends are used to create a 92.5 degree change of direction in a waste pipe system. They have a longer radius than knuckle bends and the 92.5 degree angle promotes a self-cleansing flow.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Reducer - 50mm x 40mm Grey

FloPlast Push Fit Waste Reducer - 50mm x 40mm Grey

This waste reducer is used when a 40mm waste pipe is connected into a 50mm pipe, usually with the 40mm pipe dropping into the 50mm pipe below it running towards the soil pipe.It is usually used in the branch of a 50mm tee or in one end of a 50mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 3.49
1

FloPlast Push Fit Waste Bend - 135 Degree x 32mm White

FloPlast Push Fit Waste Bend - 135 Degree x 32mm White

135 degree bends, or 45 degree bends as they are sometimes called, are used to create a change of direction in a waste pipe system. Two bends are often used together to create an offset in the pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Black

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Black

Swivel bends are used to create a tight radius 90 degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.91
1

FloPlast Push Fit Waste Reducer - 50mm x 32mm Grey

FloPlast Push Fit Waste Reducer - 50mm x 32mm Grey

This waste reducer is used when a 32mm waste pipe is connected into a 50mm pipe, usually with the 32mm pipe dropping into the 50mm pipe below it running towards the soil pipe.It is usually used in the branch of a 50mm tee or in one end of a 50mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 3.49
1

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Grey

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Grey

135 degree bends, or 45 degree bends as they are sometimes called, are used to create a change of direction in a waste pipe system. Two bends are often used together to create an offset in the pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Reducer - 40mm x 32mm White

FloPlast Push Fit Waste Reducer - 40mm x 32mm White

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe.It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Reducer - 40mm x 32mm Grey

FloPlast Push Fit Waste Reducer - 40mm x 32mm Grey

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe.It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Black

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Black

135 degree bends, or 45 degree bends as they are sometimes called, are used to create a change of direction in a waste pipe system. Two bends are often used together to create an offset in the pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.57
1

FloPlast Push Fit Waste Coupling - 32mm Grey

FloPlast Push Fit Waste Coupling - 32mm Grey

Waste couplings are used to join together two lengths of pipe. This type of system uses an O ring seal to make the joint.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.If you do plan to take the joint apart once it has been made, we would suggest the use of SL40 spray lubricant to reduce the risk of friction and possible movement of the O ring.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.57
1

FloPlast Push Fit Waste Socket Plug - 32mm Grey

FloPlast Push Fit Waste Socket Plug - 32mm Grey

This socket plug is used to gain access into the waste system for inspection and cleaning. Often referred to as a cleaning eye, it is most commonly installed into a waste tee. Socket plugs can also be used to blank off an unused connection or pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Socket Plug - 32mm White

FloPlast Push Fit Waste Socket Plug - 32mm White

This socket plug is used to gain access into the waste system for inspection and cleaning. Often referred to as a cleaning eye, it is most commonly installed into a waste tee. Socket plugs can also be used to blank off an unused connection or pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.91
1

FloPlast Push Fit Waste Socket Plug - 32mm Black

FloPlast Push Fit Waste Socket Plug - 32mm Black

This socket plug is used to gain access into the waste system for inspection and cleaning. Often referred to as a cleaning eye, it is most commonly installed into a waste tee. Socket plugs can also be used to blank off an unused connection or pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Coupling - 32mm White

FloPlast Push Fit Waste Coupling - 32mm White

Waste couplings are used to join together two lengths of pipe. This type of system uses an O ring seal to make the joint.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.If you do plan to take the joint apart once it has been made, we would suggest the use of SL40 spray lubricant to reduce the risk of friction and possible movement of the O ring.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.57
1

FloPlast Push Fit Waste Coupling - 32mm Black

FloPlast Push Fit Waste Coupling - 32mm Black

Waste couplings are used to join together two lengths of pipe. This type of system uses an O ring seal to make the joint.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.If you do plan to take the joint apart once it has been made, we would suggest the use of SL40 spray lubricant to reduce the risk of friction and possible movement of the O ring.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.57
1

FloPlast Push Fit Waste Tank Connector - 32mm Black

FloPlast Push Fit Waste Tank Connector - 32mm Black

Tank connectors are most commonly used in commercial applications in situations where a number of tanks need to be linked together.The threaded nut is unscrewed and the fitting is pushed through the hole in the tank so that the flange of the tank connector rests against the tank wall. The nut is then tightened, allowing the washer to make the seal against the tank wall.The outlet is a push fit connection to the pipe.In addition to plumbing installations, tank connectors are commonly used in the fish keeping and pond industries.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.94
1

FloPlast Push Fit Waste Tank Connector - 32mm White

FloPlast Push Fit Waste Tank Connector - 32mm White

Tank connectors are most commonly used in commercial applications in situations where a number of tanks need to be linked together.The threaded nut is unscrewed and the fitting is pushed through the hole in the tank so that the flange of the tank connector rests against the tank wall. The nut is then tightened, allowing the washer to make the seal against the tank wall.The outlet is a push fit connection to the pipe.In addition to plumbing installations, tank connectors are commonly used in the fish keeping and pond industries.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.94
1