155 resultater (0,19712 sekunder)

Vis alle filtre

Mærke

Butik

Pris (EUR)

Nulstil filter

Produkter
Fra
Butikker

FloPlast Push Fit Waste Pipe Clip - 32mm Grey

FloPlast Push Fit Waste Pipe Clip - 32mm Grey

This pipe clip is used to fix a waste pipe back to a wall. Clips should be fixed at 1.2m centres vertically and 0.5m centres horizontally for 32 and 40mm systems. For 50mm systems, the vertical centres are the same but the horizontal clip spacing can be increased to 0.6m.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.

GBP 0.79
1

FloPlast Push Fit Waste Pipe Clip - 32mm White

FloPlast Push Fit Waste Pipe Clip - 32mm White

This pipe clip is used to fix a waste pipe back to a wall. Clips should be fixed at 1.2m centres vertically and 0.5m centres horizontally for 32 and 40mm systems. For 50mm systems, the vertical centres are the same but the horizontal clip spacing can be increased to 0.6m.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.

GBP 0.79
1

FloPlast Push Fit Waste Pipe Clip - 32mm Black

FloPlast Push Fit Waste Pipe Clip - 32mm Black

This pipe clip is used to fix a waste pipe back to a wall. Clips should be fixed at 1.2m centres vertically and 0.5m centres horizontally for 32 and 40mm systems. For 50mm systems, the vertical centres are the same but the horizontal clip spacing can be increased to 0.6m.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.

GBP 0.79
1

FloPlast Square Gutter Internal Stopend - 114mm Anthracite Grey

FloPlast Square Gutter Internal Stopend - 114mm Anthracite Grey

Our Square Gutter and Fittings are manufactured by UK market leaders FloPlast.Internal Stop Ends are clipped into a fitting such an angle or running outlet to effectively cap off the guttering at that fitting.The stop end clips down and compresses the seal at the bottom of the angle or outlet, thus providing a watertight seal. Fittings with internal stop ends inserted should be supported by fixing to the fascia board to prevent the guttering from collecting water at that point and sagging.If you need any further advice any aspect of your Gutter Installation please take a look at our Guides and Tips Section.

GBP 1.87
1

FloPlast Square Gutter External Stopend - 114mm Anthracite Grey

FloPlast Square Gutter External Stopend - 114mm Anthracite Grey

Our Square Gutter and Fittings are manufactured by UK market leaders FloPlast.For a quick overview of stopends, please watch the short video below.External Stop Ends effectively cap off the guttering at the end of the run.The stop end is held to the gutter by two moulded clips, which force the gutter down and compresses the seal at the bottom of the fitting, thus providing a watertight seal. Stop Ends should be supported by a fascia bracket within 150mm of the fitting to prevent the end of the gutter run from collecting water and sagging.If you need any further advice on how to fit your guttering, you can watch a video on our Guides and Tips page.

GBP 2.89
1

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm White

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm White

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Grey

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Black

FloPlast Push Fit Waste Bend Knuckle - 90 Degree x 32mm Black

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Reducer - 40mm x 32mm Grey

FloPlast Push Fit Waste Reducer - 40mm x 32mm Grey

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe.It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Black

FloPlast Push Fit Waste Bend - 135 Degree x 32mm Black

135 degree bends, or 45 degree bends as they are sometimes called, are used to create a change of direction in a waste pipe system. Two bends are often used together to create an offset in the pipe run.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.57
1

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Swivel - 90 Degree x 32mm Grey

Swivel bends are used to create a tight radius 90 degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting.This fitting is available in 32mm and 40mm size options.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.91
1

FloPlast Push Fit Waste Reducer - 40mm x 32mm White

FloPlast Push Fit Waste Reducer - 40mm x 32mm White

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe.It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.82
1

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Black

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Black

Swept bends are used to create a 92.5 degree change of direction in a waste pipe system. They have a longer radius than knuckle bends and the 92.5 degree angle promotes a self-cleansing flow.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Grey

FloPlast Push Fit Waste Bend Swept - 92.5 Degree x 32mm Grey

Swept bends are used to create a 92.5 degree change of direction in a waste pipe system. They have a longer radius than knuckle bends and the 92.5 degree angle promotes a self-cleansing flow.This fitting is available in 32mm, 40mm and 50mm size options, with 50mm only available in grey.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 1.64
1

FloPlast Push Fit Waste Reducer - 50mm x 40mm Grey

FloPlast Push Fit Waste Reducer - 50mm x 40mm Grey

This waste reducer is used when a 40mm waste pipe is connected into a 50mm pipe, usually with the 40mm pipe dropping into the 50mm pipe below it running towards the soil pipe.It is usually used in the branch of a 50mm tee or in one end of a 50mm coupling.This push fit waste system is manufactured in the UK to BS EN 1451 and is British Standard kitemarked.When making a push fit joint, cut the pipe square and remove any burrs, push the pipe into the fitting as far as it will go and then withdraw it by approximately 10mm to allow for any expansion. The joint can be taken apart again if required, but always check that the O ring has not been dislodged from its housing groove in the fitting as this will cause the joint to leak.Click here to read our guide that explains the key differences between push fit and solvent weld waste systems.

GBP 3.49
1