8 resultater (0,18304 sekunder)

Vis alle filtre

Mærke

Butik

Pris (EUR)

Nulstil filter

Produkter
Fra
Butikker

FloPlast Solvent Weld Waste Bend Knuckle - 90 Degree x 40mm Anthracite Grey

FloPlast Solvent Weld Waste Bend Knuckle - 90 Degree x 40mm Anthracite Grey

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends._x000D_This fitting is available in 32mm, 40mm and 50mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.95
1

FloPlast Solvent Weld Waste Bend Knuckle - 90 Degree x 32mm Anthracite Grey

FloPlast Solvent Weld Waste Bend Knuckle - 90 Degree x 32mm Anthracite Grey

Knuckle bends are used to create tight, neat 90 degree bends in a waste pipe system. They have a tighter radius than the standard swept bends._x000D_This fitting is available in 32mm, 40mm and 50mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.95
1

FloPlast Solvent Weld Waste Reducer - 40mm x 32mm Anthracite Grey

FloPlast Solvent Weld Waste Reducer - 40mm x 32mm Anthracite Grey

This waste reducer is used when a 32mm waste pipe is connected into a 40mm pipe, usually with the 32mm pipe dropping into the 40mm pipe below it running towards the soil pipe._x000D_It is usually used in the branch of a 40mm tee or in one end of a 40mm coupling._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 1.06
1

FloPlast Solvent Weld Waste Bend Swivel Male and Female - 90 Degree x 40mm Anthracite Grey

FloPlast Solvent Weld Waste Bend Swivel Male and Female - 90 Degree x 40mm Anthracite Grey

Swivel bends are used to create a tight radius 90-degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting._x000D_This fitting is available in 32mm and 40mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.95
1

FloPlast Solvent Weld Waste Bend Swivel Male and Female - 90 Degree x 32mm Anthracite Grey

FloPlast Solvent Weld Waste Bend Swivel Male and Female - 90 Degree x 32mm Anthracite Grey

Swivel bends are used to create a tight radius 90 degree change of direction in a waste pipe system. They are also often referred to as M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting._x000D_This fitting is available in 32mm and 40mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.95
1

FloPlast Solvent Weld Waste Pipe Clip - 40mm Anthracite Grey

FloPlast Solvent Weld Waste Pipe Clip - 40mm Anthracite Grey

This pipe clip is used to fix a waste pipe back to a wall. Clips should be fixed at 1.2m centres vertically and 0.5m centres horizontally for 32 and 40mm systems. For 50mm systems, the vertical centres are the same but the horizontal clip spacing can be increased to 0.6m._x000D_This fitting is available in 32mm, 40mm and 50mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.83
1

FloPlast Solvent Weld Waste Bend Swivel - 135 Degree x 40mm Anthracite Grey

FloPlast Solvent Weld Waste Bend Swivel - 135 Degree x 40mm Anthracite Grey

135 degree swivel bends are used to create a tight radius 45 degree change of direction in a waste pipe system. They are also often referred to as 45 degree M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting._x000D_This fitting is available in 32mm, 40mm and 50mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first, ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well-ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 0.95
1

FloPlast Solvent Weld Waste Swivel / Conversion Bend - 92.5 Degree x 50mm Black

FloPlast Solvent Weld Waste Swivel / Conversion Bend - 92.5 Degree x 50mm Black

135 degree swivel bends are used to create a tight radius 45 degree change of direction in a waste pipe system. They are also often referred to as 45 degree M and F bends or spigot bends. They have a long tail that is usually inserted into the socket of another fitting._x000D_This fitting is available in 32mm, 40mm and 50mm size options._x000D_Our solvent weld waste is manufactured in the UK to BS EN 1455 and is kitemarked._x000D_To make a solvent weld joint, first ensure that the outer wall of the pipe and the inner wall of the fitting are both clean and free from grit or swarf. Apply SC250 solvent cement to both surfaces. Push the pipe fully into the fitting and give it a twist to ensure that full contact has been made. Clean off any excess solvent with a damp cloth and leave for 5 minutes to set. The installation should be left for 12 hours before testing._x000D_Click here to watch a step by step video of how to make a solvent weld joint._x000D_Solvent weld joints are permanent - they cannot be demounted once the joint has been made. When using solvent cement, always work in a well ventilated area and keep the cement away from heat sources or naked flames. Avoid any contact with skin - if contact does occur then wash thoroughly with soap and water.

GBP 3.49
1