825 results (0,14704 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet SensorDesigned to trigger a call when moisture is detected in a patients bed. Connects to Quantec via the jack socket on the QT637 Enuresisgeneral purpose interface socket. Typically positioned across and over amattress directly underneath the bed sheet.Key FeaturesProtects against patient discomfort and reduces the number of incontinence checks staff are required to make.Measures 80cm x 12cm and is supplied with a 2m lead and normally open right angled jack plug.Wipe clean design - can be re-used many times.

GBP 34.24
1

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02The IS electronic sounder has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The sounder unit incorporates a Two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesZones 0 1 2 20 21 and 22 ATEX and IECEx approvedIP66 ratedSurface MountPolycarbonate housing material

GBP 151.30
1

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor UnitAllows IO devices that may not be compatible with the PSUfailure requirements of BS 7273-4 Cat A to comply.Is supplied on a single gang plate with an onboard isolatingEnd of Line Unit EOL and normally energised 24V 3A rated relay.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for all compatible IO units.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for multiple coincidental loop failures sometimes required in aspecification above and beyond the requirements of BS 7273-4 for allcompatible IO units.Key FeaturesAccommodates IO units sited inside or outside the 24V Auxenclosure IO units sited remotely require a BF390 EOL unit to maintain thefailsafe functionProvides complete galvanic isolation between the fire alarmsystem and the door release systemProvides where allowed failsafe manual door releasemonitoring to BS 7273-4 Cat A utilising a single TE cable for multiplemanual operating points such as free swing doors

GBP 26.46
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Green Lens IS-SB-02-04

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Green Lens IS-SB-02-04

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Green Lens IS-SB-02-04This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof WeatherproofPlease note The blue green and white versions are all fitted with clear lenses and it is the internal LEDs which then give the colour when operated.

GBP 222.01
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof WeatherproofPlease note The blue green and white versions are all fitted with clear lenses and it is the internal LEDs which then give the colour when operated.

GBP 222.01
1

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 164.82
1

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 164.82
1

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Blue Lens IS-SB-02-03

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Blue Lens IS-SB-02-03

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Blue Lens IS-SB-02-03This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof WeatherproofPlease note The blue green and white versions are all fitted with clear lenses and it is the internal LEDs which then give the colour when operated.

GBP 222.01
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1