ProfitSpring | B2B PPC Agency

Patol Neoprene Pad for Use With the V Clip 37mm x 37mm Pack of 10

Patol Neoprene Pad for Use With the V Clip 37mm x 37mm Pack of 10The Neoprene insulation protection sleeve helps to provide linear heat detection cable with protection when using a V clip.

GBP 3.72

1

Patol ASD531 Single Sensor Standard Display with SSD531 Detector

Patol ASD531 Single Sensor Standard Display with SSD531 DetectorThe ASD 531 Aspirating Smoke Detector is the new generation of a highly sensitive active smoke detection system. It is based on the successful ASD 535 and is particularly well suited for monitoring smaller areas and sampling distances where a reduced sampling pipe network is sufficient. The ASD 531 consists of a fan a highly sensitive smoke sensor an airflow measurement system and evaluation electronics. The fan draws in air through sampling holes from the room or facility being monitored and then through a sampling pipe to the evaluating processor unit.Here the air samples are continually monitored for smoke particles by the smoke sensor. Airflow monitoring ensures that the sampling pipe is constantly checked for pipe breakage and any obstruction of the sampling holes. The display and control panel of the evaluating processor unit indicates alarm fault and status reports. Any increase in the smoke concentration levels are detected very early. Three fixed pre-alarms and one main alarm which can be forwarded to a fire alarm control panel via volt free relays contacts.The ASD 531 is used whenever conventional point-type smoke detectors cannot be used. This may be due for example to ambient conditions too hot too cold too dirty or because operating conditions are such that access is highly restricted Elevator Shafts prisons false ceilings clean rooms laboratories etc.Key Features1 sampling pipe 1 detectorEN 54-20 classes A B and C4 alarm levels 1 fire alarm 3 fixed pre-alarms 30 50 70 when using RIM36 ModuleResponse sensitivity settable from 0.00610mInsensitive to dirt particles due to particle suppressionLow noise level compliant with ISO 11690-1Perfected smoke detection with HD sensor high-dynamic technologyLow power consumptionOnboard ConfigurationASD PipeFlow calculation toolIndividually Replaceable Components Sensors PCBs etc

GBP 1031.52

1

Patol 139122P SLW 0.5bk White Silicon Wire 0.5mm Price for 100m

Patol 139122P SLW 0.5bk White Silicon Wire 0.5mm Price for 100mWhite silicon wire 0.5mm for heated sampling point.Please Note The price is for 100m of wire.

GBP 131.04

1

Patol ASD535-2 Dual Sensor Standard Display with Two SSD535-3 Detectors

Patol ASD535-2 Dual Sensor Standard Display with Two SSD535-3 DetectorsThe ASD 535 Aspirating Smoke Detector is the new generation of highly sensitive active smoke detection system. It offers application specific sensitivity adjustment alongside pre-signalling and pollution analyses. The ASD 535 detects even minuscule glowing and smouldering fires and can be deployed practically anywhere.The ASD 535 consists of one or two independent sampling lines with sampling apertures each with a highly sensitive smoke sensor. Air flow monitoring ensures that the sampling lines are constantly checked for pipe breakage and the sampling holes monitored for pollution. A high-performance ventilator draws the air from the room or facility being monitored through the sampling line to the evaluating processor unit.There the air is continuously evaluated by the smoke sensors. The display and control panel of the evaluating processor unit indicates the smoke concentration of the sampled air and other alarm fault and status messages. Any increase in the smoke concentration is detected very early. Three pre-alarms and two main alarms can be programmed for each and signalled via volt free relays contacts. There are four expansion slots for accommodating modular 1 x network card 1 x memory card and 2 relay cards.The ASD 535 is ideal for property and space surveillance thanks to its excellent response behaviour and is used whenever conventional point-type smoke detectors cannot be used. This may be due for example to ambient conditions too hot too cold too dirty or because operating conditions are such that access is highly restricted prisons false ceilings clean rooms laboratories high rack storage facilities etc.. Or because lightning-fast detection is required e.g. in data centres.Key FeaturesLatest generation of universal aspiration smoke detectors1 or 2 sampling lines with separate sensors and air flow monitoringEN54-20 classes A B and CVds certified calculation software ASD PipeFlow enables efficient asymmetrical pipe layout4 alarm levels 3 pre-alarms and 2 alarmsResolution 0.001mInsensitive to pollutants thanks to particle suppressionAuto-learning functionLow noise level compliant with ISO 11690-1Refined smoke detection thanks to HD sensor high-dynamic technologyLow power consumptionHigh performance suction 400 Pa vacuumIndividually replaceable

GBP 3114.72

1

Patol ASD535-1 Single Sensor Standard Display with SSD535-3 Detector

Patol ASD535-1 Single Sensor Standard Display with SSD535-3 DetectorThe ASD 535 Aspirating Smoke Detector is the new generation of highly sensitive active smoke detection system. It offers application specific sensitivity adjustment alongside pre-signalling and pollution analyses. The ASD 535 detects even minuscule glowing and smouldering fires and can be deployed practically anywhere.The ASD 535 consists of one or two independent sampling lines with sampling apertures each with a highly sensitive smoke sensor. Air flow monitoring ensures that the sampling lines are constantly checked for pipe breakage and the sampling holes monitored for pollution. A high-performance ventilator draws the air from the room or facility being monitored through the sampling line to the evaluating processor unit.There the air is continuously evaluated by the smoke sensors. The display and control panel of the evaluating processor unit indicates the smoke concentration of the sampled air and other alarm fault and status messages. Any increase in the smoke concentration is detected very early. Three pre-alarms and two main alarms can be programmed for each and signalled via volt free relays contacts. There are four expansion slots for accommodating modular 1 x network card 1 x memory card and 2 relay cards.The ASD 535 is ideal for property and space surveillance thanks to its excellent response behaviour and is used whenever conventional point-type smoke detectors cannot be used. This may be due for example to ambient conditions too hot too cold too dirty or because operating conditions are such that access is highly restricted prisons false ceilings clean rooms laboratories high rack storage facilities etc.. Or because lightning-fast detection is required e.g. in data centres.Key FeaturesLatest generation of universal aspiration smoke detectors1 or 2 sampling lines with separate sensors and air flow monitoringEN54-20 classes A B and CVds certified calculation software ASD PipeFlow enables efficient asymmetrical pipe layout4 alarm levels 3 pre-alarms and 2 alarmsResolution 0.001mInsensitive to pollutants thanks to particle suppressionAuto-learning functionLow noise level compliant with ISO 11690-1Refined smoke detection thanks to HD sensor high-dynamic technologyLow power consumptionHigh performance suction 400 Pa vacuumIndividually replaceable

GBP 2073.12

1

Patol ASD535-3 Single Sensor Full Display with SSD535-3 Detector

Patol ASD535-3 Single Sensor Full Display with SSD535-3 DetectorThe ASD 535 Aspirating Smoke Detector is the new generation of highly sensitive active smoke detection system. It offers application specific sensitivity adjustment alongside pre-signalling and pollution analyses. The ASD 535 detects even minuscule glowing and smouldering fires and can be deployed practically anywhere.The ASD 535 consists of one or two independent sampling lines with sampling apertures each with a highly sensitive smoke sensor. Air flow monitoring ensures that the sampling lines are constantly checked for pipe breakage and the sampling holes monitored for pollution. A high-performance ventilator draws the air from the room or facility being monitored through the sampling line to the evaluating processor unit.There the air is continuously evaluated by the smoke sensors. The display and control panel of the evaluating processor unit indicates the smoke concentration of the sampled air and other alarm fault and status messages. Any increase in the smoke concentration is detected very early. Three pre-alarms and two main alarms can be programmed for each and signalled via volt free relays contacts. There are four expansion slots for accommodating modular 1 x network card 1 x memory card and 2 relay cards.The ASD 535 is ideal for property and space surveillance thanks to its excellent response behaviour and is used whenever conventional point-type smoke detectors cannot be used. This may be due for example to ambient conditions too hot too cold too dirty or because operating conditions are such that access is highly restricted prisons false ceilings clean rooms laboratories high rack storage facilities etc.. Or because lightning-fast detection is required e.g. in data centres.Key FeaturesLatest generation of universal aspiration smoke detectors1 or 2 sampling lines with separate sensors and air flow monitoringEN54-20 classes A B and CVds certified calculation software ASD PipeFlow enables efficient asymmetrical pipe layout4 alarm levels 3 pre-alarms and 2 alarmsResolution 0.001mInsensitive to pollutants thanks to particle suppressionAuto-learning functionLow noise level compliant with ISO 11690-1Refined smoke detection thanks to HD sensor high-dynamic technologyLow power consumptionHigh performance suction 400 Pa vacuumIndividually replaceable

GBP 2424.24

1

Patol ASD535-4 Dual Sensor Full Display with SSD535-3 Detectors

Patol ASD535-4 Dual Sensor Full Display with SSD535-3 DetectorsThe ASD 535 Aspirating Smoke Detector is the new generation of highly sensitive active smoke detection system. It offers application specific sensitivity adjustment alongside pre-signalling and pollution analyses. The ASD 535 detects even minuscule glowing and smouldering fires and can be deployed practically anywhere.The ASD 535 consists of one or two independent sampling lines with sampling apertures each with a highly sensitive smoke sensor. Air flow monitoring ensures that the sampling lines are constantly checked for pipe breakage and the sampling holes monitored for pollution. A high-performance ventilator draws the air from the room or facility being monitored through the sampling line to the evaluating processor unit.There the air is continuously evaluated by the smoke sensors. The display and control panel of the evaluating processor unit indicates the smoke concentration of the sampled air and other alarm fault and status messages. Any increase in the smoke concentration is detected very early. Three pre-alarms and two main alarms can be programmed for each and signalled via volt free relays contacts. There are four expansion slots for accommodating modular 1 x network card 1 x memory card and 2 relay cards.The ASD 535 is ideal for property and space surveillance thanks to its excellent response behaviour and is used whenever conventional point-type smoke detectors cannot be used. This may be due for example to ambient conditions too hot too cold too dirty or because operating conditions are such that access is highly restricted prisons false ceilings clean rooms laboratories high rack storage facilities etc.. Or because lightning-fast detection is required e.g. in data centres.Key FeaturesLatest generation of universal aspiration smoke detectors1 or 2 sampling lines with separate sensors and air flow monitoringEN54-20 classes A B and CVds certified calculation software ASD PipeFlow enables efficient asymmetrical pipe layout4 alarm levels 3 pre-alarms and 2 alarmsResolution 0.001mInsensitive to pollutants thanks to particle suppressionAuto-learning functionLow noise level compliant with ISO 11690-1Refined smoke detection thanks to HD sensor high-dynamic technologyLow power consumptionHigh performance suction 400 Pa vacuumIndividually replaceable

GBP 3385.20

1

Patol 710-020 Controller 5020 for Spares Only

Patol 710-020 Controller 5020 for Spares Only - for use with Sensor Models 5010 5012 5712The 5020 controller is directly connected to the sensor. A series of user programmable DIL switches allows option selection including detector sensitivity settings automanual reset sequence selection and single coincidence voting from the four individual internal detection channels for the alarm trip and shutdown outputs.The Sensor Unit is located above the materials transit path e.g. conveyor by means of the adjustable mounting bracket and aligned such that the monitored hazard passes through the sensors field of view. The height and angle of the sensor determine the width of the monitored path.The Type 5020 Control Unit provides various indications and controls related to infra-red detection alarms and fault monitoring.The control module is easily de-mountable from the housing and connects to the sensor by means of a ten core screened shielded cable. These terminations together with supply and output contact connections are via two part screw terminals thus enabling installation of the housing and site cables prior to fitment of the module. The housing has a high level of ingress protection IP67.The unit incorporates a user programmable DIL switch to set the options which include detector sensitivity setting automanual reset sequence selection and one-shot coincidence voting for the alarm and tripshutdown outputs.The sensor air pressure and signal cable connections are fault monitoredfail safe. The unit incorporates an aux. fault input common fault output contact.The 5020 Controller also includes LED indication of the four detector channels along with LED indication and relay outputs for Alarm Trip and Fault.The controller can be provided in an optional outer control panel together with power supplies battery chargers DIN rail terminals as required.Key FeaturesMaterial Fan Case - White Polyester Resin Impellors - Aluminium 1200 H14IP Rating IP44Weight 8.5Kg

GBP 2076.48

1

Patol 700-701 Digital Zener Barrier - MTL - For Use With LDM-519-DIM Only

Patol 700-701 AnalogueDigital Zener Barrier - MTL - For Use With LDM-519-DIM OnlyThe Patol 700-701 is an intrinsically safe IS zener barrier that can be used to communicate with and provide isolations for LHDC approved for use in hazardous areas.These barriers limit the amount of energy allowed to pass into the hazardous area which inhibit ignition in flammable atmospheres.Key FeaturesThis product is designed for use with the LDM-519-DIM onlyApproved for use in hazardous areasLimits energy to hazardous areasPlease note The 700-701 can only be used with thePatol Digital LDM-519-DIM Din Rail Mounted LHDC Monitor 2kmLDM-519-DIM.

GBP 423.43

1

Patol 700-702 AnalogueDigital Zenner Barrier - MTL - for use with LDM-519-DDL Z only

Patol 700-702 AnalogueDigital Zenner Barrier - MTL - for use with LDM-519-DDL Z onlyThe Patol 700-702 is an intrinsically safe IS Zenner Barrier that can be used to communicate with and provide isolations for LHDC approved for use in hazardous areas.These barriers limit the amount of energy allowed to pass into the hazardous area which inhibit ignition in flammable atmospheres.Please note 700-702 is for use with LDM-519-DDL Z only.

GBP 440.16

1

Patol ADB 500 Automatic Blowout Device for One Sampling Pipe 50-0500571-01-01P

Patol ADB 500 Automatic Blowout Device for One Sampling Pipe 50-0500571-01-01PThe automatic blow out device ADB 500 is used as an accessory part for an Aspirating Smoke Detector in areas with high levels of dust and dirt.With the blow out device the aspirating smoke detectors sampling pipe is automatically blown through and cleaned to prevent fault messages due to contaminated suction openings and false alarms. This way the lifespan of the smoke sensor in the aspirating smoke sensor is increased considerably.When using the automatic blow out device a combination with the accessory components dust filter unit DFU 911 and dust retaining box DRB 25 is generally recommended. Optionally the filter-box FBX 25 extra-large and the dirt trap box DTB 25 can be used.Key FeaturesPrevention of fault messages caused by contaminated suction openings.Lengthening of lifespan of smoke detectors smoke sensorsPrevention or substantial reduction of false alarmsFault message in the case of compressed air failure detection period can be freely programmedApplicable for all aspirating smoke detectorsSubsequent installation possible at any timeLow installation costsMaintenance friendly

GBP 2576.04

1

Patol ADB 2000 Automatic Blowout Device for Two Sampling Pipes 50-0500523-01-01P

Patol ADB 2000 Automatic Blowout Device for Two Sampling Pipes 50-0500523-01-01PThe Automatic Blowout Device ADB 2000 is used as an accessory part for an Aspirating Smoke Detector in areas with high levels of dust and dirt.With the Blowout Device the aspirating smoke detectors sampling pipe is automatically blown through and cleaned to prevent fault messages due to contaminated suction openings and false alarms.This way the lifespan of the smoke sensor in the aspirating smoke sensor is increased considerably.Key FeaturesPrevention of fault messages caused by contaminated suction openingsLengthening of lifespan of smoke detectors smoke sensorsPrevention or substantial reduction of false alarmsFault message in the case of compressed air failure detection period can be freely programmedApplicable for all aspirating smoke detectorsSubsequent installation possible at any timeLow installation costsMaintenance friendly

GBP 6750.62

1

Patol ADB 1000 Automatic Blowout Device for One Sampling Pipe 50-0500520-01-01P

Patol ADB 1000 Automatic Blowout Device for One Sampling Pipe 50-0500520-01-01PThe Automatic Blowout Device ADB 1000 is used as an accessory part for an Aspirating Smoke Detector in areas with high levels of dust and dirt.With the Automatic Blowout Device the aspirating smoke detectors sampling pipe is automatically blown through and cleaned to prevent fault messages due to contaminated suction openings and false alarms.This way the lifespan of the smoke sensor in the aspirating smoke sensor is increased considerably.Key FeaturesPrevention of fault messages caused by contaminated suction openings.Lengthening of lifespan of smoke detectors smoke sensorsPrevention or substantial reduction of false alarmsFault message in the case of compressed air failure detection period can be freely programmedApplicable for all aspirating smoke detectorsSubsequent installation possible at any timeLow installation costsMaintenance friendly

GBP 3842.04

1

Patol Stainless Steel Cable Collector for Roof Tank

Patol Stainless Steel Cable Collector for Roof TankThe cable collector has been designed to work in conjunction with the retractable cable. As the retractable cable extends and contacts the cable collector will allow the cable to be neatly coiled without it getting caught as the roof rises.

GBP 680.40

1

Patol 4041F Air Purge Filter for 50405041

Patol 4041F Air Purge Filter for 50405041A replacement air purge filter for the 50405041 Air Purge Units.Air purge filters are intended to preserve blower life in normal conditions. They can be easily removed from an Air Purge Unit and are washable.

GBP 126.00

1

Patol N45X7A-W01 One Year LHD Interrogator Warranty Extension For N4587A or N4517A

Patol N45X7A-W01 One Year LHD Interrogator Warranty Extension For N4587A or N4517AThe Patol N45X7A-W01 is a one year LHD interrogator warranty extension designed for use with N4587A or N4517A.

GBP 2142.00

1

Patol RFC 911 Replacement Cartridge for DFU 911 11-2300031-01-01P

Patol RFC 911 Replacement Cartridge for DFU 911 11-2300031-01-01PA replacement cartridge for the DFU 911.

GBP 50.57

1

Patol Stainless Steel Cable Ties for Clips amp Fixings 150mm Pack of 10

Patol Stainless Steel Cable Ties for Clips Fixings 150mm Pack of 10Cable ties are for use on the Patol range of fixings and clips. They however cannot be used directly on linear heat detection cable instead a neoprene sleeve must be over the cable to protect it.

GBP 5.16

1

Patol Black Nylon Cable Ties for Clips amp Fixings 200mm Pack of 100

Patol Black Nylon Cable Ties for Clips Fixings 200mm Pack of 100Cable ties are for use on the Patol range of fixings and clips. They however cannot be used directly on linear heat detection cable instead a neoprene sleeve must be over the cable to protect it.

GBP 13.20

1

Patol Black Nylon Cable Ties for Clips amp Fixings 300mm Pack of 100

Patol Black Nylon Cable Ties for Clips Fixings 300mm Pack of 100Cable ties are for use on the Patol range of fixings and clips. They however cannot be used directly on linear heat detection cable instead a neoprene sleeve must be over the cable to protect it.

GBP 13.20

1

Patol 50-0500410-01-01 FBL 25 PC Replacement Filter for Large Filter Box Pack Of 5

Patol 50-0500410-01-01 FBL 25 PC Replacement Filter for Large Filter Box Pack Of 5The 50-0500410-01-01 FBL 25 PC Replacement Filter by Patol is designed for use with large filter boxes.

GBP 67.20

1

Patol RFC 911 VE20 Replacement Cartridge for DFU 911 - 20 pcs 11-2300031-02-01P

Patol RFC 911 VE20 Replacement Cartridge for DFU 911 - 20 pcs 11-2300031-02-01PRFC 911 VE20 Replacement Cartridge for the DFU 911.Key Features20 pieces

GBP 841.68

1

Patol Digital EOL ABS Termination Box for DDL Range with Fire amp Fault Test Key Switch

Patol Digital EOL ABS Termination Box for DDL Range with Fire Fault Test Key SwitchThe Patol End of Line EOL junction boxes are designed to terminate either Analogue and Digital LHDC. The EOL unit provides fault monitoring on the cable. Analogue EOL units can monitor for both open and closed circuit faults. Digital EOLs monitor for open circuit faults.Key FeaturesABS PlasticIP66120mm x 120mm x 80mm1 x PG7 Gland

GBP 328.03

1

Patol Digital EOL ABS Termination Box for DIM Range with Fire amp Fault Test Key Switch

Patol Digital EOL ABS Termination Box for DIM Range with Fire Fault Test Key SwitchThe Patol End of Line EOL junction boxes are designed to terminate either Analogue and Digital LHDC. The EOL unit provides fault monitoring on the cable. Analogue EOL units can monitor for both open and closed circuit faults. Digital EOLs monitor for open circuit faults.Key FeaturesABS PlasticIP66120mm x 120mm x 80mm1 x PG7 Gland