278 results (0,15757 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Vesda Xtralis Discreet Clear End Cap for 10mm OD Tube Pack of 10

Vesda Xtralis Discreet Clear End Cap for 10mm OD Tube Pack of 10

Vesda Xtralis Discreet Clear End Cap for 10mm OD Tube Pack of 10Vesda Xtralis Capillary 10mm Discreet Endcap - with over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Please note The 222-059 is equivalent to the REDCAP010N.

GBP 5.22
1

Vesda Sensepoint XCL XCL-VEA-CH4-RA-5 Methane CH4 0-100 LEL 4-20mA Relays - Pack of 5

Vesda Sensepoint XCL XCL-VEA-CH4-RA-5 Methane CH4 0-100 LEL 4-20mA Relays - Pack of 5

Vesda Sensepoint XCL XCL-VEA-CH4-RA-5 Methane CH4 0-100 LEL 4-20mA Relays - Pack of 5Xtralis has developed with its sister company Honeywell Analytics a new concept of aspirated gas detectors. When used with the VESDA-E VEA VESDA Sensepoint XCL provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.Through its embedded Bluetooth interface VESDA Sensepoint XCL enables customers to pair the gas detector with their smart device applications to perform installation commissioning and maintenance. This ensures a faster VESDA Sensepoint XCL installation rapid configuration simplicity to operate and simplified maintenance.Key FeaturesAvailable SensorsCarbon Dioxide CO2 0 5000ppmCarbon Dioxide CO2 0 5.0 vvHydrogen H2 0 1000ppmCombustible CAT 0 100 LEL Methane Hydrogen Propane Ethanol Butane Octane etc.Carbon Monoxide CO 0 1000ppmFactory calibrated detectors CAT Factory calibrated to CH4Integral alarm status LEDsBluetooth 4.0 Bluetooth Low EnergyIntegrates with PLCsHVACBMSFACPConfigurable relays4-20 mA analogue outputs or RS 485 Modbus output

GBP 4634.11
1

Vesda Sensepoint XCL XCL-VEA-CH4-RA Methane CH4 0-100 LEL 4-20mA Relays

Vesda Sensepoint XCL XCL-VEA-CH4-RA Methane CH4 0-100 LEL 4-20mA Relays

Vesda Sensepoint XCL XCL-VEA-CH4-RA Methane CH4 0-100 LEL 4-20mA RelaysXtralis has developed with its sister company Honeywell Analytics a new concept of aspirated gas detectors. When used with the VESDA-E VEA VESDA Sensepoint XCL provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.Through its embedded Bluetooth interface VESDA Sensepoint XCL enables customers to pair the gas detector with their smart device applications to perform installation commissioning and maintenance. This ensures a faster VESDA Sensepoint XCL installation rapid configuration simplicity to operate and simplified maintenance.Key FeaturesAvailable SensorsCarbon Dioxide CO2 0 5000ppmCarbon Dioxide CO2 0 5.0 vvHydrogen H2 0 1000ppmCombustible CAT 0 100 LEL Methane Hydrogen Propane Ethanol Butane Octane etc.Carbon Monoxide CO 0 1000ppmFactory calibrated detectors CAT Factory calibrated to CH4Integral alarm status LEDsBluetooth 4.0 Bluetooth Low EnergyIntegrates with PLCsHVACBMSFACPConfigurable relays4-20 mA analogue outputs or RS 485 Modbus output

GBP 1424.17
1

Vesda Sensepoint XCL XCL-VEA-CH4-RM Methane CH4 0-100 LEL Modbus amp Relays

Vesda Sensepoint XCL XCL-VEA-CH4-RM Methane CH4 0-100 LEL Modbus amp Relays

Vesda Sensepoint XCL XCL-VEA-CH4-RM Methane CH4 0-100 LEL Modbus RelaysXtralis has developed with its sister company Honeywell Analytics a new concept of aspirated gas detectors. When used with the VESDA-E VEA VESDA Sensepoint XCL provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.Through its embedded Bluetooth interface VESDA Sensepoint XCL enables customers to pair the gas detector with their smart device applications to perform installation commissioning and maintenance. This ensures a faster VESDA Sensepoint XCL installation rapid configuration simplicity to operate and simplified maintenance.Key FeaturesAvailable SensorsCarbon Monoxide CO 0 1000ppmCombustible CAT 0 100 LEL Methane Hydrogen Propane Ethanol Butane Octane etc.Hydrogen H2 0 1000ppmCarbon Dioxide CO2 0 5.0 vvCarbon Dioxide CO2 0 5000ppmFactory calibrated detectors CAT Factory calibrated to CH4Integral alarm status LEDsBluetooth 4.0 Bluetooth Low EnergyIntegrates with PLCsHVACBMSFACPConfigurable relays4-20 mA analogue outputs or RS 485 Modbus output

GBP 1507.57
1

Vesda Sensepoint XCL XCL-VEA-CO-RA-5 Carbon Monoxide CO 0-300PPM 4-20mA Relays - Pack of 5

Vesda Sensepoint XCL XCL-VEA-CO-RA-5 Carbon Monoxide CO 0-300PPM 4-20mA Relays - Pack of 5

Vesda Sensepoint XCL XCL-VEA-CO-RA-5 Carbon Monoxide CO 0-300PPM 4-20mA Relays - Pack of 5Xtralis has developed with its sister company Honeywell Analytics a new concept of aspirated gas detectors. When used with the VESDA-E VEA VESDA Sensepoint XCL provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.Through its embedded Bluetooth interface VESDA Sensepoint XCL enables customers to pair the gas detector with their smart device applications to perform installation commissioning and maintenance. This ensures a faster VESDA Sensepoint XCL installation rapid configuration simplicity to operate and simplified maintenance.Key FeaturesAvailable SensorsCarbon Monoxide CO 0 1000ppmCombustible CAT 0 100 LEL Methane Hydrogen Propane Ethanol Butane Octane etc.Hydrogen H2 0 1000ppmCarbon Dioxide CO2 0 5.0 vvCarbon Dioxide CO2 0 5000ppmFactory calibrated detectors CAT Factory calibrated to CH4Integral alarm status LEDsBluetooth 4.0 Bluetooth Low EnergyIntegrates with PLCsHVACBMSFACPConfigurable relays4-20 mA analogue outputs or RS 485 Modbus output

GBP 5028.35
1

Vesda Sensepoint XCL XCL-VEA-CO-RA Carbon Monoxide CO 0-300PPM 4-20mA Relays

Vesda Sensepoint XCL XCL-VEA-CO-RA Carbon Monoxide CO 0-300PPM 4-20mA Relays

Vesda Sensepoint XCL XCL-VEA-CO-RA Carbon Monoxide C0 0-300PPM 4-20mA RelaysXtralis has developed with its sister company Honeywell Analytics a new concept of aspirated gas detectors. When used with the VESDA-E VEA VESDA Sensepoint XCL provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.Through its embedded Bluetooth interface VESDA Sensepoint XCL enables customers to pair the gas detector with their smart device applications to perform installation commissioning and maintenance. This ensures a faster VESDA Sensepoint XCL installation rapid configuration simplicity to operate and simplified maintenance.Key FeaturesAvailable SensorsCarbon Monoxide CO 0 1000ppmCombustible CAT 0 100 LEL Methane Hydrogen Propane Ethanol Butane Octane etc.Hydrogen H2 0 1000ppmCarbon Dioxide CO2 0 5.0 vvCarbon Dioxide CO2 0 5000ppmFactory calibrated detectors CAT Factory calibrated to CH4Integral alarm status LEDsBluetooth 4.0 Bluetooth Low EnergyIntegrates with PLCsHVACBMSFACPConfigurable relays4-20 mA analogue outputs or RS 485 Modbus output

GBP 1283.04
1

Vesda Xtralis PIP-015 Flush Sample Point Head Only for 10mm OD Tube

Vesda Xtralis PIP-015 Flush Sample Point Head Only for 10mm OD Tube

Vesda Xtralis PIP-015 Flush Sample Point Head Only for 10mm OD TubeDue to the aesthetic design of some buildings such as ornate ceilings or ceiling art-work a discreet unobtrusive smoke detection system is often desirable. Large open atria or voids feature stratified thermal layers that can prevent cooled smoke from reaching ceiling level. As such conventional systems will normally only respond when a fully-fledged fire condition is reached by which time significant damage has already occurred.VESDA provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location. The room fabric often dictates the location of these capillary tubes. Hiding the capillary tubes behind light fittings blending in with ceiling paintings or forming part of the ceiling sculptures can all be used to provide invisible smoke detection. In high volume atria applications such as cathedrals capillary sample points can be routed into the area at intermediate vertical levels to good effect to overcome stratification. The higher potential sensitivity of the VESDA system means that less smoke is required at the sample points to provide an alarm condition.With over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Key FeaturesFor use with Red or White ABSOperating temperature range -40C to 70CLPCB approvedEN54 testedApplications Used inChurchesHospitalsMuseums GalleriesPrisonsLibrariesArchivesConcert HallsPlease Note The PIP-015 is equivalent to the REDASP025F.

GBP 9.07
1

Vesda 020-052 19quot Enclosure for Sub-Rack 2 Rows

Vesda 020-052 19quot Enclosure for Sub-Rack 2 Rows

Vesda 020-052 19 Enclosure for Sub-Rack 2 RowsTo compliment the VESDA range of detectors displays and programmers a 19 inch Subrack enclosure is available. The 19 inch rack enclosure is designed to house up to 12 display andor programmer modules VESDAnet sockets or relay only modules in a wide variety of configurations to suit the particular requirements of a site where centralized control and monitoring of the VESDA system is required.19 Subracks can be installed in glass fronted enclosures and are mounted on a swing frame for convenient connection of all the cables. Cable entry for 24 VDC power VESDAnet connection and interfacing to the relays is provided by multiple knock-outs on all four sides of the box. 19 Subracks and blank panels must be ordered separately. Each enclosure will accommodate up to 3 subracks. If utilising only 1 or 2 racks the VESDA Power Supply VPS-100-US-xxx can also be mounted in the enclosure.A detector enclosure is also available which incorporates a small glass window to view an on-board display. The detector enclosure enables a single detector to be installed in challenging environments where a high IP rating is required.Key FeaturesDual hinged glass door provides easy access to VESDA modules and termination boardsSecond door provides access to the termination boardsDesigned for easy mountingMultiple knock-outs for easy cable entryHolds up to 3 subracksFull size lockable window and door

GBP 2037.12
1

Vesda Xtralis VPS-215-E5 24V 0.5A Power Supply Unit 7AHR

Vesda Xtralis VPS-215-E5 24V 0.5A Power Supply Unit 7AHR

Vesda Xtralis VPS-215-E5 24V 0.5A Power Supply Unit 7AHRXtralis Power Supply Units are uniquely designed to complement the style and appearance of Xtralis aspirating smoke detectors ASDs and are technically matched to provide sufficient current and battery charging capacity to meet the requirements of EN 54-4.The Style E variants are VdS certified and CE marked to the EN54-4 so are particularly suitable for use in territories where these approvals are required.The 0.5A load with 7Ah batteries max is the budget unit within the range.It is intended as a low-cost unit to supply a single pipe ASD detector which only requires 7Ah batteries such as the VESDA VLF-250.A simple but elegant construction and no LEDs on the lid keep the cost of the unit to a minimum.The unit can also be inverted where necessary by rotating the lid.The internal charger is EN54-4 certified and internal LEDs are provided to indicate OK output healthy and Fault.

GBP 242.62
1

Vesda Xtralis F-PC-6.5 Standard-Clip for ASD Pipework 6.5mm

Vesda Xtralis F-PC-6.5 Standard-Clip for ASD Pipework 6.5mm

Vesda Xtralis F-PC-6.5 Standard-Clip for ASD Pipework 6.5mmA standard clip for aspirating holes 6.5mm in the colour blue.When installing an Aspirating Smoke Detection ASD system it is often almost impossible to identify the exact location of sampling point and more importantly identify if the sampling hole is the correct size creating unnecessary delays.The VESDA Sampling Hole Clip delivers reliable and accurate sampling hole sizes that are fast to install and easy to locate and identify. Each clip is colour-coded to indicate a specific hole diameter providing an instant visual guide and removing the need for closer inspection.This is particularly beneficial during commissioning and maintenance processes in applications like warehouses or large open spaces. The greatly simplified installation process helps deliver greater reliability in the correct setting of sampling hole size and a faster installation process. A 10mm 2764 diameter drill bit is all that is required by an installer to create each sampling hole rather than many different drill sizes to which the Sampling Hole Clip attaches to.This can help deliver quality installation in projects where installation is sub contracted or the installer is not familiar with the impact of sampling hole size. Use of a chamfered hole entry in the sampling hole clip design can help to reduce dust loading effects.Without using this type of technology a build-up of dust around a standard drilled sampling hole is likely to occur due to the friction created by the airflow through the sampling hole. By reducing dust loading effects and leveraging the additional protection provided by the pipe clips sites can help increase system uptime and potentially extend service and testing intervals.Unlike most contemporary solutions the pipe clip is installation-ready with no need for assembly any additional parts or tools clips are provided as a single ready-to-fit piece.The pipe clips are also available in two formats Standard and Harsh Environment. Harsh Environment Clip variants feature a flexi-lip design that changes its shape when subjected to compressed air.This helps any ice fibre or dust build-up on the supporting rubber structure be easily detached and broken up by the air Jetstream out of the clip hole providing additional protection in challenging locations like freezer applications.Key FeaturesPre-engineered sampling holes for faster more efficient commissioning and installationInstallation-ready design with no part assembly or tools required simply clicks into place for a firm non-slip positionVisual colour-coded guide to sampling point location and sampling hole sizeGreatly simplifies sampling hole drilling a single 10mm drill bit for all holes simply fit the relevant clip to set the hole sizeReduces dust loading effects through inclusion of a chamfered hole entry design helping to increase uptime and potentially extends test intervalsTwo formats available Standard and Harsh EnvironmentHarsh Environment Clip variants feature a flexi-lip design to help reduce sampling hole contamination under high air pressure

GBP 21.32
1