ProfitSpring | B2B PPC Agency

Aico Spare Key for Ei407 Call Point MCRSK

Aico Spare Key for Ei407 Call Point MCRSKThe MCRSK is a spare or replacement Singular Spare Key designed for use with the Ei407.

GBP 1.49

1

Aico EI650i Optical Smoke Alarm - 10 Year Lithium Battery Powered

Aico EI650i Optical Smoke Alarm - 10 Year Lithium Battery PoweredFunctioning as a standalone unit the Ei650i Optical Alarmis best for detecting slow smouldering fires commonly produced by electricalfires or flammable materials. This Optical Fire Alarm is best placed in thehallway landing living room or dining room.This battery powered alarm contains sealed in tamper-prooflithium battery that will last for the full 10-year life of the alarm. Thealarm is not powered until it is twisted on the mounting base thus avoidingbattery power consumption during storage and prior to installation.Key FeaturesPowered by a sealed 10-year lithium batteryBuilt-in dust compensation technologyBuilt-in AudioLINK technologyEasy to fit with twist on base multi-fixings andanti-tamper locking optionEasy to use large test buttonGrade F1 and Kitemarked to BS EN 146042005

GBP 31.43

1

Aico Spare Key for MCP401RC Call Point MCPSK2

Aico Spare Key for MCP401RC Call Point MCPSK2The Aico Spare Singular Key for MCP401RC.Resets the call point by inserting the key in to the base and rotating this then Pops the Plastic Shield back into place.

GBP 1.49

1

Aico Vibrating Pad for use with Alarms Ei174

Aico Vibrating Pad for use with Alarms Ei174The Ei174 is an additional Vibration Pillow Pad designed for use with Ei Alarms for the hearing impaired. It comes with a 5m of cable and plugs into an alarm kit using the socket plug supplied. It provides additional warning where more than one vibrating pillow pad is needed.Key FeaturesActivates on receipt of an alarm signalPlugs directly into the alarms strobe unit5 year guarantee

GBP 34.45

1

Aico Fire Blanket for Household use 1.1m x 1.1m - Ei522

Aico Fire Blanket for Household use 1.1m x 1.1m - Ei522This is the Aico Ei522 Fire Blanket For Kitchen and Clothing fires suitable also for wall mounting if necessary. The Ei522 is a fire blanket designed for use with pan fires and small fires. It is suitable for wall mountingKey FeaturesFor domestic use small kitchenand clothing firesSuitable for pan fires e.g. chip pan and other small firesSize 1.1m x 1.1mTested to BS EN18691997Can be wall mounted

GBP 34.20

1

Aico Surface Mount Kit for 2100 160RC amp 140RC Series Alarms Ei127

Aico Surface Mount Kit for 2100 160RC 140RC Series Alarms Ei127The Ei127 is a Surface Mount Kit for use with 2100 160RC and 140RC Series Smoke and Heat Alarms. It allows additional space for wiring connections. It has 3 x 1625mm trunking knock outs for surface wiring.Key FeaturesFits under any 2100 160RC 140RC series alarms3 way connector block used for wiring mains and interconnect

GBP 4.15

1

Aico EI144E Heat Alarm - 230V with Alkaline Battery Back-up - Easi-fit Base

Aico EI144E Heat Alarm - 230V with Alkaline Battery Back-up - Easi-fit BaseThe Ei144e Heat Alarm is a mains powered unit and can be interlinked with other Aico alarms through either a hard wired or wireless interconnection.The alarm is supplied with an easi-fit base to make it as quick and simple to install.Alarm SitingDifferent alarms sensors work best at detecting different types of fire and so should be sited in appropriate rooms throughout a property. Heat alarms are best at detecting large fast flaming fires which are commonly caused by kitchen fires. The Ei144e is suitable for Kitchen and GarageThe Heat alarm will react to the heat in the Kitchen or Garage rather than smoke making it more resistant to fumes such as burnt toast and therefore less likely to false alarm.RadioLINK TechnologyAs with the rest of the 140e Series alarms the Ei144e Heat alarm can be interconnected with other alarms and accessories through hard wire connection or for less mess and disruption by RadioLINK wireless interconnection.Key FeaturesHeat sensor responds to heat build-up from large flaming fires triggers at 58CMains powered with 9V Alkaline battery back-upEasi-fit base for quick and simple installationKitemarked to BS 5446-220035 year guarantee

GBP 51.42

1

Aico RadioLINK Alarm for Deaf 230V with Strobe Vibrating Pad Ei170RF

Aico RadioLINK Alarm for Deaf 230V with Strobe Vibrating Pad Ei170RFTheEi170RF is a mains powered with rechargeable battery back up alarm kitfor the deaf and hard of hearing. Thekit contains aXenon strobe lightthat provide and plug in vibrating pillow pad that will activate when the interconnected alarms are triggered to alert theuser tothe danger.TheEi170RF kit is compatible with the3000Multi-Sensor Fire Alarm Ei2110e160e Seriesalarms and 140RC Series smoke and heat alarms along with any interconnected Carbon Monoxide alarms. This kit links into the alarm system usingRadioLINK wireless interconnection technology making it easier to add into a system and causing less disruption to the occupants on installation.An integral Test button is also present on the front of the unit allowing an easy means of testing the strobe vibration pad and the RadioLINK enabled alarms in the system.As with other RadioLINK products the Ei170 Alarm Kit for the Deaf and Hard of Hearing will need to belinked into the alarm system or House Coded. View ourstep by step guide to House Coding here.Technical Specification A strobe and vibrating pillow pad kit designed to give warning of fire to deaf and hard of hearing occupants. For use with30002110e160eand 140RC Series smoke and heat alarms when used with aRadioLINK baseRadioLINK moduleor theSmartLINKmoduleRadioLINK Carbon MonoxideCO alarms. It can also be used with all other RadioLINK devicesancillaries including the 600 Series RadioLINK smoke and heat alarms.Eliminates the need for any cabling between the Ei170 RF and the smoke heat andor CO alarms used in the system.Requires 230V AC 50Hz mains power supply.The unit has a built-in high-intensity Xenon strobe flash rate 0.8Hz with a wide light output angle.Built-in long life sealed lead acid rechargeable battery to provide back-up power in the event of mains failure. Standby capacity 7 days followed by 15 minutes alarm lifespan 5 years in normal use. The battery is connected by plugging it into the socket in the bottom of the battery box.Comprehensive indicating lights on front of the unitPower Constant green to indicate mains is present flashes amber every 4 seconds with mains absent.Alarm red Flashes every second when the unit has been triggered.Fault amber Flashes every 4 seconds if a fault is detected with panelvibration pad. Flashes every 4 seconds if rechargeable back-up battery is depleted or faulty.RF status blue Illuminates when RF signal is being sent flashes in House Code mode to indicate the number of units learned. Flashes every 40 seconds if RadioLINK smoke alarms have a low battery.Mains transformer is mounted in separate and hard-wired to the strobe unit with 4m of low voltage cable. Supplied with 2m of mains cable and pre-wired 13 amp plug with a 3 amp fuse.Integrated Test button on the front of the unit. Pressing this checks strobe and control circuitry and also send out a RadioLINK alarm signal to other units in the system.The vibrating pillow pad is suitable for mounting under mattresses or pillows and produces strong pulsed vibrations suitable for waking sleepers. Supplied with locking plug and 5m of pre-wired cable.Connecting sockets on rear of unit as followsVibration Pad socket Locking socket JST type VHR-2N. Is pulsed when unit is in alarm.Auxiliary sockets Two auxiliary sockets are available on the rear of the unit to allow connection of additional strobes etc. Locking sockets JST type VHR-2N. Each provides 12V200mA when unit is in alarm. Can be used for any of the following Auxiliary strobe Ei178 auxiliary vibration pad Ei174 or for triggering a radio pager.A clock input socket is also available. This is for use will alarm clocks that have a 3.5mm mono jack output and saves the need for multiple vibration pads. An input of 5-12V AC or DC mains isolated will turn on the vibration pad constant vibration pattern but will not activate the strobe or auxiliary sockets.Radio frequency 868MHz band in accordance with RTTE Directive 19995EC this band has been designed for use with security products and only allows a 1 duty cycle so continuous transmission and interference from external sources is extremely remote and would be illegal. Complies with EN300220-2V2.1.1.RF Range The type of building will be the major limiting factor e.g. the number and type of wallsceilings that the radio signal has to pass through. As a guide 30m should be the maximum distance between any of the RadioLINK units in the system.Up to 12 RadioLINK units can be used in one system. For larger systems contact our Technical Department for guidance.

GBP 279.71

1

Aico Marking Plate for changing 150 Series Alarm to 2100 160RC or 140RC Alarms Ei1516

Aico Marking Plate for changing 150 Series Alarm to 2100 160RC or 140RC Alarms Ei1516The Ei1516 Masking Plate is designed to cover any marks left from rectangular shaped alarms when upgrading to30002110e160eor 140RC Series smoke and heat alarmsEi168RCRadioLINK bases andEi128REi128RBURelay Modules which are round in shape.It has adhesive strips to keep the plate aligned when installing.Operation of theEi1516 Masking PlateThe masking plate can be attached to the base of an alarmunit.The plate and base can then be screwed to the ceiling covering any marks left from the previous alarm.Technical Specification The Ei1516 is designed for use with 3000 2110e 160e or 140RC Series smoke and heat alarms Ei168RC RadioLINK bases and Ei128ReI128RBU relay modules.Complete with screw holes and wiring cut out.Adhesive strips provided keep the plate aligned when installing.Dimensions 176mm x 3mm.Weight 29g.Manufactured in IrelandFoam gasket on the back to reduce drafts and dust ingress.

GBP 2.35

1

Aico EASI-FITBASE Easi-Fit Base For Use With 140RC and 3000 Series Alarms

Aico EASI-FITBASE Easi-Fit Base For Use With 140RC and 3000 Series AlarmsAicos easi-fit base has been proven to give quick reliable installation and comes with all our mains powered fire alarms such the 3000 Series and 140e Series. The first easi-fit bases were launched in 1999 and have become a firm favourite with installers ever since.All Aico mains powered smoke and heat alarms along with all future product developments are compatible with easi-fit bases meaning you wont need to wire in a new base when you come to re-new or upgrade the alarms.Key FeaturesA clip on wiring coverTamper-proof locking latchRemovable trunking pull-out 25mmBuilt-in terminal blockClearly labelled wiring terminals

GBP 5.04

1

Aico Ei3014 230v 3000 Series Heat Alarm

Aico Ei3014 230v 3000 Series Heat AlarmSuitable for detecting Heat in both the kitchen or garagethe Ei3014 Heat Alarm contains our tried and tested high-performance ThermistorHeat sensor. The Thermistor has been designed using a smaller thermal massproviding a faster alarm response when the trigger temperature of 58C isreached. Best for detecting heat build-up from large flaming fires it candifferentiate from smoke or steam to drastically reduce false alarms.The Ei3014 Heat Alarm is SmartLINK compatible Simply plugin an Ei3000MRF module for wireless interconnection data extraction andreal-time notifications of alarm activations and events via the SmartLINKGateway and Portal.The Heat Alarm contains AudioLINKtechnology which allowsyou to extract real time data from the alarm using its sounder directly to asmartphone or tablet via an App. A simple to read report is generateddisplaying details such as activation dates sensor status and alarm life thatcan be emailed to help form part of property records.The Ei3014 Heat Alarm is fully compatible with all otherAico alarms and accessories whether a system needs upgrading or an existingsystem needs expanding and works with either hard-wired RadioLINK or hybridinterconnecting systems.Key FeaturesContains a fast response Thermistor Heat sensorMains powered with a 10-year rechargeable lithium cellback-upAdd an Ei3000MRF SmartLINK module for wirelessinterconnection and data extractionCompatible with other Aico mains powered devicesBuilt-in AudioLINK data extraction technologyGrade D1 and compliant with Scottish legislationSupplied with an easy-fit base10 Year Guarantee

GBP 73.07

1

Aico EI650iRF RadioLINK Optical Smoke Alarm - 10 Year Lithium Battery Powered - With AudioLink

Aico EI650iRF RadioLINK Optical Smoke Alarm - 10 Year Lithium Battery Powered - With AudioLink The Ei650iRF is a battery-powered Optical Smoke Alarm. It is able to wirelessly interconnect with any other RadioLINK RadioLINK and SmartLINK products. Contains an Optical Smoke ChamberThe Ei650iRF RadioLINK Optical Smoke Alarm is best for detecting slow smouldering fires commonly produced by electrical fires or sofas and is less likely to react to cooking smells if fitted in the hallway next to the kitchen.Battery and LifespanThis battery powered alarm contains sealed in tamper-proof lithium battery that will last for the full 10-year life of the alarm. The alarm is not powered until it is twisted on the mounting base thus avoiding battery power consumption during storage and prior to installation.Built-in RadioLINK Wireless Interconnection TechnologyRadioLINK wireless interconnection technology is built-in to this alarm. RadioLINK uses Radio Frequency signals to link alarms together with added functionality. All RadioLINK alarms and devices should be House Coded together upon install.Key FeaturesOptical sensor with dust compensation technologyBuilt-in AudioLINKUses built-in RadioLINK technology to interconnect and for data extractionConnects wirelessly with all other Aico wireless interconnection productsBattery powered with a sealed-in lithium batteryEasy to fit twist on base and multi-fixings with an anti-tamper locking option10-year lifeGrade F1 and compliant with Scottish legislationKitemarked to BS EN 146042005

GBP 94.61

1

Aico Ei3016 230v 3000 Series Optical Smoke Alarm

Aico Ei3016 230v 3000 Series Optical Smoke AlarmThe Ei3016 Optical Smoke Alarm contains a high-performance optical smoke sensor which is best for detecting slow smoldering fires. In addition the smoke chamber design integrated insect screen and unique automatic dust compensation reduce the risk of false alarms. The Ei3016 runs on 230V AC mains power. In the event of mains failure the 10 Year built in tamper-proof rechargeable lithium cells will provide back-up supply and continuous operation.The Ei3016 contains AudioLINK technology which allows you to extract real time data from the alarm directly to a smartphone or tablet via the AudioLINK App. The Ei3016 self-checks its sensor battery and internal circuitry every 48 seconds. Any fault condition found will be indicated by a combination of yellow LED flashes andor audible beeps. The memory feature allows an alarm that has previously activated to be easily identified through the red flashing LED.The alarm is fitted with a large Test Silence button to facilitate frequent testing of the alarm and system. The silence function allows the alarm system to be silenced in the case of a false nuisance alarms and low battery fault beeps. SmartLINK compatible - plug in an Ei3000MRF module for wireless interconnection data extraction and real-time notifications of alarm activations and events via the SmartLINK Gateway and Portal.Key FeaturesContains a high-performance optical sensorMains powered with 10-year rechargeable Lithium cell back-upCompatible with interconnection and monitoring technologyAudioLINK TM Data extraction technologyDust compensation - unique self-monitoring mechanismEasi-Fit base10 Year lifeSensor Type OpticalSupply Voltage 230V AC 50HzPower Consumption 0.25W standbyBattery Back-up Rechargeable lithium cellsSound Level 85dBA at 3mButton Test Checks sensor electronics and sounderSilence Function Silences alarm for 10 minutesSilence Function Silences fault beeps for 12 hoursAudioLINK EnabledSmartLINK Compatible via the Ei3000MRF ModuleIndicator LEDS Green power. Red alarm silence mode memory. Yellow fault eventMemory Records last alarm eventFixing easi-fit base suppliedOperating Temperature -10C to 40CHumidity Range 15 to 95 relative humidityPlastic Material UL 94 V0 flame retardant

GBP 72.89

1

Aico Ei171RF RadioLINK Flashing Strobe with Rechargeable Back-up

AicoEi171RFRadioLINK Flashing Strobe with Rechargeable Back-upThe Ei171RF is a RadioLINK alarm accessory that is designed to give warning to the deaf and hard of hearing if their alarm system has activated. It consists of a mains powered strobe light with a rechargeable battery back-up. This strobe has been designed specifically for daytime rooms as a visual indicator with a specially designed lens for wide-angle light output.For protection in a bedroom we recommend the Ei170RF alarm kit as this combines a strobe light and a vibrating pillow pad for extra warning.This Strobe Light is compatible with the 3000 Multi-Sensor Fire Alarm Ei2110e 160e Series alarms and 140RC Series smoke and heat alarms along with any interconnected Carbon Monoxide alarms. This kit links into the alarm system using RadioLINK wireless interconnection technology making it easier to add into a system and causing less disruption to the occupants on installation.As with other RadioLINK products the Ei17iRF Strobe for the Deaf and Hard of Hearing will need to be linked into the alarm system or House Coded.Key FeaturesFor use with 3000 2110e 160e and 140RC Series smoke and heat alarms when used with a RadioLINK base RadioLINK module or a SmartLINK module and RadioLINK Carbon Monoxide CO alarms it can also be used with all other RadioLINK devicesancillariesEliminates the need for any cabling between the Ei170 RF and the smoke heat andor CO alarms used in the systemRequires 230V AC 50Hz mains power supplyBuilt-in high-intensity Xenon strobe flash rate 0.8Hz with a wide light output angleBuilt-in long life sealed lead acid rechargeable batteryMains transformer is mounted in separate and hard-wired to the strobe unit with 4m of low voltage cable. Supplied with 2m of mains cable and pre-wired 13 amp plug with a 3 amp fuseIntegrated Test button on the front of the unit. Pressing this checks strobe and control circuitry and also send out a RadioLINK alarm signal to other units in the systemUp to 12 RadioLINK units can be used in one system. For larger systems contact our Technical Department for guidanceAn optional additional strobe Ei178 is available for providing warning in additional rooms The Ei178 is supplied with 10m of pre-wired cable and plug for connection to one of the auxiliary socketsThe product is CE marked to indicate conformance to directives EMC 89336EEC tested to EN50130-4 Low Voltage 7323EEC tested to EN60065 RTTE 19995EC tested to EN300220-2V2.1.1Designed for wall or surface mountingDimensions Control box 195mm x 125mm x 75mm. Mains adapter 60mm x 50mm x 90mmWeight Control box 770g. Mains adapter 600gAmbient Temperature Range 4C to 40C. Humidity Range 0 to 90 relative humidity5-year guarantee

GBP 245.27

1

Aico Relay Module with 5A Relay Mounts under 2100 160RC amp 140RC Alarms Ei128R

Aico Relay Module with 5A Relay Mounts under 2100 160RC 140RC Alarms Ei128RThe Ei128R is a mains powered Relay Module that triggers external devices such as a strobe light or telecare deviceif the alarmsin the propertyactivate.Compatible with the3000Ei2110e Multi-Sensor Fire Alarm160e Seriesalarms and the 140RC SeriesThe Module has additional trunking knock outsto make as easy to install as possibleand is designed to fit underneath the space of easy-fit or RadioLINK base. However a cover is supplied if needed and containsa set of volt-free contacts as standard.The Relay module can beconfigured to give a 230V output or a 24V output using an external 24V supply.Operation of the Ei128ROn receiving a signal from the alarm system the relay contacts will be operated causing a signal to be sent to the device to which it is connected.The Ei128R can be used to switch into a range of devices ranging from indicating lights to magnetic door handles.The module can be switched to give a pulse output or continuous output for different applications.Technical SpecificationThe Relay is designed to operate whilst the alarm system is sounding to signal ancillary devices such as door closers extractors remote sounders etc. When any of the interconnected alarms sound the signal will cause the relay contacts to switch.The Relay is mains powered and operates on receipt of a signal from the interconnect line of a smoke heat or CO alarm. The relay does not operate if mains power is not present.Volt free contacts Normally Open or Normally Closed rated up to 240V AC5 Amps making it suitable for use with a wide range of AC or DC voltages.The Ei128R is designed for siting under one of the smokeheat alarms listed above. However a cover is supplied if installing remotely or with 260 series CO alarms.More than one Relay can be used in a set of interconnected alarms on the condition that no more than 12 units are used in the system 1 x Ei128R counts as one unit.Fitted with a 4 way connector block for ease of wiring.The relay can be set for Continuous or Pulse operation by operation of a manual switch when in Pulse operation mode the relay contacts will automatically switch back to their original state after 5 seconds.Features 3 x 25mm trunking knockouts for surface wiring and centre knockout for recess wiring.Dimensions of unit 135mm diameter x 20mm depth.Weight inclusive of packaging 170g.Manufactured in Ireland.Key FeaturesFor use with the 2100 160RC and 140RC series alarmsVolt free contacts as supplied for multiple useCan be configured to switch a 230V or 24V deviceTrunking knock-outs for easy and neat wiringAdditional connectors for ease of wiringContinuous or pulse operationFits discreetly behind any smoke heat alarm5 Year Guarantee

GBP 43.28

1

Aico Relay Module with 5A Relay amp Rechargeable Back-up Ei128RBU

Aico Relay Module with 5A Relay Rechargeable Back-up Ei128RBUThe Ei128RBU is a Relay Module that runs on a 230V AC mains power and has built-in tamper-proof Lithium cells that act as a battery back up in the event of mains failure. These rechargeable lithium cells are designed to have a 10-year life and outlast the life of the module itself whilst providing up to 2 months of operation without mains power.The Module has a set of Volt free contacts Normally Open and Normally Closed as standard but can be configured to give a 230V output or a 24V output using an external 24V supply.Any combination of30002110e160e 140RC or 260RC Series alarms can be used up to 12 including the Relay.The Module is designed to fit underneath any smoke or heat alarm. However a cover is supplied if there is a need for siting the unit remotely.The Module has additional trunking knock outs for ease of wiring.The Module can give a Continuous or pulse output. The pulse output will switch back the Relay contacts to their original state after 5 seconds operation.Operation of the Ei128RBUOn receiving a signal form the alarm system the Relay contacts will be operated causing a signal to be sent to the device to which it is connected.The Ei128RBU can be used to switch into a range of devices ranging from warden call systems to panel systems.When modified for a 230V or 24V output they can operate a range of different devices.The Module can be switched to give a pulse output or continuous output for different applications.Technical Specification The Relay is designed to operate whilst the alarm system is sounding to signal devices such as panels warden call systems nurse call systems etc. When any of the interconnected alarms sound the signal will cause the relay contacts to switch.The Relay runs on 230V AC mains power and has built in tamper proof Lithium cells that act as a battery back up in the event of mains failure. These rechargeable Lithium cells are designed to have a 10 year life and outlast the life of the module itself whilst providing up to 2 months of operation without mains power. It operates on receipt of a signal form the interconnect line of a smoke heat or CO alarm.Volt-free contacts Normally Open or Normally Closed rated up to 240V AC 5 Amps making it suitable for use with a wide range of AC or DC voltages.Any combination of 3000 2110e 160e 140RC or 260RC smoke heat or CO alarms can be interconnected to a maximum of 12 units in total 1 x Ei128RBU counts as one unit.The Ei128RBU is designed for siting under one of the smokeheat alarms listed above. However a cover is supplied if installing remotely or with 260 series CO alarms.More than one Relay can be used in a set of interconnected alarms on the condition that no more than 12 units are used in the system 1 x Ei128RBU counts as one unit.Fitted with a 4 way connector block for ease of wiring.The Relay can be set for continuous or pulse operation through a manual switch when in pulse operation mode the Relay contacts will automatically switch back to their original state after 5 seconds.Features 3 x 25mm trunking knockouts for surface wiring and centre knockout for recess wiring.Dimensions of unit 135mm diameter x 20mm depth.Weight inclusive of packaging 265g.Manufactured in Ireland.Key FeaturesFor use with 2100 160RC and 140RC alarmsRechargeable lithium battery back-upVolt free contacts as supplied for multiple useCan be configured to switch a 230V or 24V deviceTrunking knock-outs for easy and neat wiringAdditional connectors for ease of wiringContinuous or pulse operationFits discreetly behind any smoke heat alarm5 Year Guarantee

GBP 71.82

1

Aico RadioLINK Relay Module with 5A Relay amp Rechargeable Battery Back-up Ei428

Aico RadioLINK Relay Module with 5A Relay Rechargeable Battery Back-up Ei428The Ei428 is a mains powered relay module that triggers external devices such as a strobe light or telecare deviceif the alarmsin the propertyactivate.For use with 140RC when using anEi168Rc RadioLINK base160ewhen using andEi100MRF RadioLINK module Ei3000 series when using anEI3000MRF SmartLINK moduleor any RadioLINK enabled CO alarms.The module has additional trunking knock outsto make as easy to install as possibleand is designed to fit underneath the space of easi-fit or RadioLINK base. However a cover Ei128COV is available if needed and containsa set of volt free contacts as standard.The replay module can beconfigured to give a 230V output or a 24V output using an external 24V supplyOperation of Ei428 RadioLINK Relay ModuleOn receiving a RadioLINK signal from one of the alarms in the system the relay contacts will be operated causing a signal to be sent to the system to which it is connectedThe indicator on the cover will show a constant green light when the mains power is connected.Technical SpecificationA relay module with cover to allow flexibility in siting.For use with 140RC when using anEi168Rc RadioLINK base160ewhen using andEi100MRF RadioLINK module Ei3000 series when using anEI3000MRF SmartLINK moduleor any RadioLINK enabled CO alarms.Eliminates the need for any cabling between the Ei428 and the smoke heat and CO alarms used in the system.Requires 230V AC Mains Power Supply Green LED to indicate mains power is present.Features built-in tamper proof Rechargeable Vanadium Pentoxide lithium standby cells capable of lasting at least 10 years and powering the module initially for at least 2 months in the event of mains power failure. The cell manufacturer endorses a minimum 10-year life expectation for the rechargeable cells which are activated by operating the battery switch inside the module.The product is CE marked to indicate conformance to BS EN 600651998 Electrical Safety EN300220-1 V1.3.1 2000-09 RF Performance EN301489 V1.4.1 2002 08 EMC and has been 3rd party tested for electrical safety in accordance with Annex K of BS 5446 Pt.12000.Radio frequency 868 MHz Band in accordance with RTTE Directive 19995EC this band has been designated for use with security products and only allows a 1 duty cycle so continuous transmission and interference form external sources is extremely remote and would be illegal.Range The type of building will be the major limiting factor e.g. the number and type of wallsceilings that the radio signal has to pass through. As a guide 30m should be the maximum distance between any of the RadioLINK units in the system.Up to 20 RadioLINK units can be used in one system. Range will be the limiting factor.Low back-up warning signal LED indicator flashes RED every 10 seconds to indicate that the lithium cells are depleted.Units are in Factory Code mode when received they will all communicate with each other. They must be House Coded to eliminate the risk of adjacent properties communicating with each other. After House Coding they will only communicate with other RadioLINK units coded at the same time.House Code Operate the House Code switch on all RadioLINK units in the system see the instructions supplied with other RadioLINK units being used. The green LED on the cover of the Ei428 will change to red and flash slowly this indicates that it will receive the unique serial numbers being sent by all other RadioLINK units in House Code. The number of flashes of the LED indicates the number of units in the system The Ei428 will return to normal standby mode automatically after 15 minutes. Pressing the House Code switch again will return it to normal standby immediately.Volt free contacts Normally Open or Normally Closed rated up to 240V AC 5 Amps making it suitable for use with a wide range of AC or DC voltages. The relay contacts operate on mains power or on back-up cells in the event of mains failure.A RadioLINK Manual Call Point Ei407 and remote control switches Ei450 Ei412 and Ei411H are also available for use in the system. See separate specification sheets for further information.Features 1 x 25mm trunking for for surface wiring and centre knockout for recess wiring.Ambient Temperature Range 4C to 40C. Humidity Range 0 to 90 relative humidity.Dimensions 140mm diameter x 27mm depth weight inclusive of packaging 220g.5 year guarantee.Manufactured in Ireland.Key FeaturesDesigned for use with all RadioLINK Professional alarms and accessoriesRechargeable Lithium battery back-upVolt-free contacts as supplied for multiple usesCan be configured to switch a 230V or 24V outputTrunking knock-outs for easy and neat wiringContinuous or Pulse operation5 Year Guarantee

GBP 98.36

1

Aico YO3 230V Multi Frequency Sounder

Aico YO3 230V Multi Frequency SounderThe YO3 is a 230V AC powered electronic sounder for fire security and industrial applications.The mains powered Sounder connects into the alarm system via a relay base or module such a the Ei428 or the Ei128RU. If the alarms trigger the relay will send out a signal that triggers the Sounder.The Sounder emits between the frequency of 340-2900Hz with 32 different tones that you can select and has an output of 90-100dBA at 1 meter.The tone of the sound can be changed using the 6-way DIL Switch.Key FeaturesMoulded flame retardant ABS plastic construction with stainless steel screws230V AC operation 15mA power consumption32 selectable sounds via a 6 way DIL switchFrequency from 340Hz 24002900KHzOutput levels from 90 to 100dB A 1mAdditional adjustable sound control on the circuit board3 x 20mm gland entries provided for cable supplyInsulated clamping terminals provided for 0.5mm to 1.5mm cableWeather protected to IP66Operating temperature -25C to 55CRelative Humidity 90 20CDimensions 85 x 85 x 75mmWeight 370gManufactured in the E.U5 year guarantee

GBP 103.41

1

Aico Ei3024 230v 3000 Series Optical and Heat Multi-Sensor Fire Alarm

Aico Ei3024 230v 3000 Series Optical and Heat Multi-Sensor Fire AlarmThe Ei3024 Multi-Sensor Fire Alarm contains both Optical and Heat sensors to provide total fire coverage. Intelligent software allows it to detect all fire types TF1 to TF6 TF8 surpassing traditional single sensor Alarms. In addition the chamber design integrated insect screen and unique dust compensation algorithm reduce the risk of false alarms. The Ei3024 runs on 230V AC mains power. In the event of mains failure the 10 Year built in tamper-proof rechargeable lithium cells will provide back-up supply and continuous operation.The Ei3024 contains AudioLINK technology which allows you to extract real time data from the alarm directly to a smartphone or tablet via the AudioLINK App. The memory feature allows an alarm that has previously activated to be easily identified through the red flashing LED. The Ei3024 self tests its sensors battery and internal circuitry every 48 seconds. Any fault condition found will be indicated by a combination of yellow LED flashes andor audible beeps.The Ei3024 is fitted with a large central Test Silence button to facilitate frequent testing of the alarm and system. The silence function allows the alarm system to be silenced in the case of a false nuisance alarm and low battery fault beeps. SmartLINK compatible - plug in an Ei3000MRF module for wireless interconnection data extraction and real-time notifications of alarm activations and events via the SmartLINK Gateway and Portal.Key FeaturesSensor Types Optical Thermistor10 year lifeEasi-fit baseDust compensation unique self-monitoring mechanismAudioLINK data extraction technologyCompatible with other Aico mains powered unitsAdd an Ei3000MRF module for wireless interconnection and data extractionMains powered with 10 year rechargeable lithium cell back-upContains both an Optical and Heat sensor for a total fire responseSupply Voltage 230V AC 50HzPower Consumption 0.25W standbyBattery Back-up Rechargeable lithium cellsSound Level 85dBA at 3mButton Test Checks sensors electronics and sounderSilence Function Silences alarm for 10 minutesSilence Function Silences fault beeps for 12 hoursAudioLINK EnabledSmartLINK Compatible via the Ei3000MRF ModuleIndicator LEDS Green power. Red alarm silence mode memory. Yellow fault eventMemory Records last alarm eventFixing easi-fit base suppliedOperating Temperature -10C to 40CHumidity Range 15 to 95 relative humidityPlastic Material UL 94 V0 flame retardantDimensions Product 150mm x 66mmDimensions Boxed 180mm x 155mm x 70mmWeight 346g product only 412g boxedGuarantee 5 years

GBP 95.08

1

Aico YO5 High Output Sounder

Aico YO5 High Output SounderThe YO5 is a mains-powered sounder for fire security and industrial applications. It connects to the alarm system via a relay base or module such as the Ei428 or the Ei128R. The sounder output is selectable from 400-2850Hz with 32 different tonesKey FeaturesFrequency of 400-2850Hz switchable89 102 dBA at 1mMains poweredActivate via a Relay ModuleIndoor or outdoor use IP65

GBP 138.19

1

Aico Ei1529RC Alarm Control Switch

Aico Ei1529RC Alarm Control SwitchThe Ei1529RC is a remote control switch that runs on 230V AC mains power. It is designed for use with 2100 160RC and 140RC series smoke and heat alarms and 260RC series carbon monoxide alarms.It increases the flexibility and user friendliness of the alarms by allows the user to remotely Locate Hugh and Test the alarms in the systemLocate The source of the alarmHush any nuisance alarmsTest the alarm systemMains Check provides warning of a mains failureKey FeaturesInstall as part of the system to get more control over your alarmsMains poweredHard wired interconnectionTest Locate and SilenceCompatible with 3000 Ei2110e Multi-Sensor Fire Alarm 160e Series alarms 140RC Series alarms and hard wired interconnected Carbon Monoxide alarmsCompiles with electrical safety requirements EN61000-6-12007 Et EN61000-6-22005 EMC Directive and EN600652001 A122011 Low voltage directiveCarries the CE mark to indicate conformance to Low Voltage and Electromagnetic Compatibility DirectivesWall mounted for ease of use can be fixed with surface mount box supplied or will fit a standard recessed box not suppliedSuitable for siting at any convenient point in the property. Up to 4 x Ei1529RC switches can be installed in a hardwired system along with a maximum of 16 x 3000 2110e 160e or 140RC Series smoke and heat alarms or 261ENRC Carbon Monoxide alarmsThe unit incorporates 3 switches marked Locate Test and Hush. These provide control features as detailed below and a mains check function as detailed below

GBP 48.71

1

Aico Ei630i Heat Alarm - 10 Year Lithium Battery Powered

Aico Ei630i Heat Alarm - 10 Year Lithium Battery PoweredThe Ei630i is a battery powered Heat Alarm that contains a sealed in tamper proof lithium battery that will last for the full 10 year life of the alarm.Battery and LifespanThe Ei630i is a battery powered Heat Alarm that contains a sealed in tamper-proof lithium battery that will last for the full 10 year life of the alarm.Built-in AudioLINK TechnologyThis second iteration of the award-winning AudioLINK technology makes it simple to get real-time data from the Ei630i Heat Alarm via the AudioLINK app. The App generates a simple to read colour-coded report giving information on a range of alarm data such as alarm activations sensor status and record of testing.Key FeaturesHeat sensor responds to heat build-up from large flaming fires triggers at 58C10 year Lithium battery poweredEasy to fit twist on base and multi-fixingsKitemarked to BS 5446-220035 year guarantee

GBP 31.20

1

Aico EI3028 Series Heat amp Carbon Monoxide Multi-Sensor Fire Alarm

Aico EI3028 Series Heat Carbon Monoxide Multi-Sensor Fire AlarmThe Ei3028 is a Multi-Sensor Heat and Carbon Monoxide CO Alarm. It contains our proven fast acting Class A1 Thermistor sensor to detect fire as well as our proven electrochemical CO sensor to detect the presence of toxic levels of CO. This provides protection from both Fire and CO in one alarm. The Ei3028 runs on 230V AC mains power. In the event of mains failure the 10 Year built in tamper-proof rechargeable lithium cells will provide back-up supply and continuous operation.The Ei3028 contains AudioLINK technology which allows you to extract real time data from the alarm directly to a smartphone or tablet via the AudioLINK App. During an alarm Fire or CO indicators will flash on the Alarm to indicate what has been detected. There will also be a different alarm sound depending on what has triggered the alarm. The Ei3028 is fitted with a large Test Silence button to facilitate frequent testing of the alarm and system. The silence function allows the alarm system to be silenced in the case of a false nuisance alarms and low battery fault beeps.The Ei3028 self-tests its sensors battery and internal circuitry every 48 seconds. Any fault condition found will be indicated by a combination of yellow LED flashes andor audible beeps. SmartLINK compatible - plug in an Ei3000MRF module for wireless interconnection data extraction and real-time notifications of alarm activations and events via the SmartLINK Gateway and Portal.Key FeaturesSensor Type Thermistor Electrochemical CO10 year lifeEasi-fit baseHeat or CO indicator on alarm headAudioLINK data extraction technologyCompatible with other Aico mains powered unitsAdd and Ei3000MRF for wireless interconnection and data extractionMains powered with 10 year rechargeable lithium cell back-upContains both a Heat and Electrochemical CO sensor Heat and CO coverage in one alarmSupply Voltage 230V AC 50HzPower Consumption 0.25W standbyBattery Back-up Rechargeable lithium cellsSound Level 85dBA at 3mButton Test Checks sensors electronics LED displays and sounderSilence Function Silences alarm for 10 minutes if alarm is triggered by heat or once for 4 minutes in case of CO event.Silence Function Silences fault beeps for 12 hoursAudioLINK EnabledSmartLINK Compatible via the Ei3000MRF ModuleIndicator LEDS Green power. Red pre-alarm CO only alarm silence mode memory or battery event. Yellow fault eventMemory Records last alarm eventFixing easi-fit base suppliedOperating Temperature -10C to 35CHumidity Range 15 to 95 relative humidityPlastic Material UL 94 V0 flame retardantDimensions Product 150mm x 66mmDimensions Boxed 180mm x 155mm x 72mmWeight 318g product only 384g boxedGuarantee 5 years

GBP 117.24

1

Aico RadioLINK Manual Call Point Ei407

Aico RadioLINK Manual Call Point Ei407This call point is powered by a tamper proof sealed inlithium cell giving a completely wire free installation with a 10-year life.The front plate is made from a non-breaking plastic that means if the callpoint is used you can simply reset the plate rather than having to replace it.The Ei407 connects wirelessly using RadioLINKinterconnection technology so once in place you will need to House Code theswitch into the alarm system.Operation The indicator will flash green every 40 seconds to indicatethat the battery is healthyThe indicator will flash amber every 9 seconds to indicatethat the batteries are depletedKey FeaturesAllows for remote triggering of an alarm systemNon-breaking re-settable front platesContains 10-year lithium cell for completely wire freeinstallationConnects wirelessly with all other Aico wirelessinterconnection productsTechnical SpecificationFor use with 140RC when using anEi168Rc RadioLINK base160ewhen using andEi100MRF RadioLINK module Ei3000 series when using anEI3000MRF SmartLINK moduleor any RadioLINK enabled CO alarmsEliminates the need for any cabling between the Ei407 and the smoke andor heat alarms within the systemFeatures built-in tamper proof FDK Lithium cells capable of lasting at least 10 years under normal usage. operating the yellow onoff switch sited on the back of the unit activates the cells. The LED on the front cover will flash red amber green on power up after this it will flash green every 40 seconds to indicate a healthy power supply. If the LED flashes amber every 40 seconds this indicates a depleted battery and the complete unit must be replacedThe product is CE marked to indicate conformance to BS EN 600651998 Electrical Safety EN300220-1 V1.3.1 2000-09 RF Performance EN301489 V1.4.1 2002-08 EMC and has been 3rd party tested for electrical safety in accordance with Annex K of BS 5446 Pt 12000Radio frequency 868MHz in accordance with RTTE Directive 19995EC this band has been designated for use with security products and only allows a 1 duty cycle so continuous transmission and interference from external sources is extremely remote and would be illegalUp to 12 RadioLINK units can be used in one system. For larger systems contact our Technical Department for guidance also see section 7Range the type of building will be the major limiting factor e.g. the number and type of wallsceilings that the radio signal has to pass throughLow battery warning signal LED indicator flashes amber every 40 seconds to indicate depleted battery if this occurs the complete unit should be replacedSimply key to rest the unit no broken glassReplacement key MCRSK availableAmbient temperature range 4c to 40c. Humidity range 0 to 90 relative humidityExternal alarm RadioLINK signal operates sounder on any smoke alarm with a RadioLINK in the systemUnits are in factory code when received they will all communicate with each other. They must be House Coded to eliminate the risk of adjacent properties communicating with each other. After house coding they will only communicate with other units coded at the same timeHouse Code Operate the red House Code switch on the back of the unit. At the same time put all other RadioLINK units in the system into House Code see relevant instruction leaflets. The red LED on the front cover will flash rapidly to indicate that it is in House Code. Each RF base will learn the serial numbers of all units in the system any other RadioLINK units. The number of flashes of the amber light on the RF units indicates the number of alarms in the system. All units will return to normal standby mode automatically after 15 minutes. Pressing the House Code switch again will return them to normal standby immediatelyThe Ei407 can be incorporated into a system consisting of any additional RadioLINK componentsDimensions 85mm x 85mm x 57mm deep including mounting boxWeight 240g including packaging5 year guaranteeManufactured in Ireland

GBP 58.33

1

Aico Ei3018 230v 3000 Series Carbon Monoxide Alarm

Aico Ei3018 230v 3000 Series Carbon Monoxide AlarmThe Ei3018 is a Carbon Monoxide CO Alarm powered by 230V AC mains power and has built in tamper proof rechargeable lithium cells that act as a battery back up in the event of mains failure. These rechargeable lithium cells are designed to last the life of the CO alarm. The Ei3018 has a high performance proven electrochemical sensor 10 year life to sense CO presence. The sensor is individually calibrated and tested in CO gas to ensure accuracy. In alarm the flash rate of the red LED indicates the level of CO detected.The Ei3018 contains AudioLINK technology which allows you to extract real time data from the alarm directly to a smartphone or tablet via the AudioLINK App. The Ei3018 can operate as a standalone alarm or can be interconnected either by hard-wire or wirelessly using the EI3000MRF module enabling it to communicate with compatible alarms and accessories. Up to 12 devices can be interconnected.The memory feature allows an alarm that has previously activated to be easily identified through the red flashing LED. The alarm is fitted with a large Test Silence button to facilitate frequent testing of the alarm and system. The silence function allows the alarm system to be silenced in the case of a false nuisance alarms and low battery fault beeps. SmartLINK compatible - plug in an Ei3000MRF module for wireless interconnection data extraction and real-time notifications of alarm activations and events via the SmartLINK Gateway and Portal.Key FeaturesSensor Types Electrochemical cell10 year lifeEasi-fit baseAudioLINK data extraction technologyCompatible with other Aico mains powered devicesAdd an Ei3000MRF module for wireless interconnection and data extractionMains powered with 10 year rechargeable lithium cell back-upContains our proven Electrochemical CO sensorSupply Voltage 230V AC 50HzPower Consumption 0.25W standbyBattery Back-up Rechargeable lithium cellsSound Level 85dBA at 3mButton Test Checks sensors electronics and sounderSilence Function Silences alarm for 10 minutesSilence Function Silences fault beeps for 12 hoursAudioLINK EnabledSmartLINK Compatible via the Ei3000MRF ModuleIndicator LEDS Green power. Red pre alarm alarm silence mode memory. Yellow fault eventMemory Records last alarm eventOperating Temperature -10C to 35CHumidity Range 15 to 95 relative humidityPlastic Material UL 94 V0 flame retardantDimensions Product 150mm x 55mmDimensions Boxed 180mm x 155mm x 62mmWeight 310g product only 376g boxedGuarantee 5 years

GBP 89.60

1

Brand

Merchant

Price (EUR)