36 results (0,17111 seconds)

Show all filters

Brand

Size

Merchant

Price (EUR)

Reset filter

Products
From
Shops

4x C-TEC CAST Zone Monitor Module

4x C-TEC CAST Zone Monitor Module

LPCB certified to EN54-17 & 18 and Kiwa Telefication certified to EN54-13. A single-zone addressable Zone Monitor capable of supporting up to 20 conventional fire detectors and 10 MCPs Mountable on a standard UK 25mm double gang back box. Onboard short-circuit loop isolator. 4mA typical alarm current (1.1mA typical quiescent current) @ 22-40V DC. Indicators for Loop polling, input faults and relay status. Alternatively, can be used as general purpose input monitor. Mountable on a C-TEC NCP-26 surface box or a standard UK 25mm double gang back box (not supplied).

GBP 207.96
1

6x C-TEC Single Gang Jack Plate for EVC401/PH

6x C-TEC Single Gang Jack Plate for EVC401/PH

A single gang jack plate designed for use in conjunction with an EVC401/JPH portable fire telephone handset on compatible SigTEL emergency voice communication systems. Can be mounted on 25mm UK flush or surface single gang back box. When the handset (not supplied) is plugged into the Jack Plate it will call theSigTEL master controller from where a two-way speech channel can be opened and instructions communicated. Multiple jack plates can be connected to a single SigTEL Master Controllerline in stairwells, etc. Designed for use in regions where roaming handsets are accepted (typically the Far and Middle East). UK standard BS5839-9 DOES NOTallow the use ofthese devices. Facilitatesreliable two-way communication in anemergency between a permanently manned control room and key points ofasite.

GBP 239.94
1

9x C-TEC Auxiliary Device Isolator

9x C-TEC Auxiliary Device Isolator

Allows a +24 VDC output from a fire alarm control panel to be remotely isolated to prevent autodiallers, water sprinklers, rollershutters, etc., from activating. Designed so that if monitoring is used on the +24 VDC output being controlled, a fault condition will show at the fire panel when the device is Isolated. Label includes a white write on areaallowing installers to add equipment locations. Fits on standard UK 25mm flush or surface mount back boxes.

GBP 179.91
1

3x C-TEC Dual Phono Line Level Outreach Plate

3x C-TEC Dual Phono Line Level Outreach Plate

Accepts stereo phono line-level input signals from sources such as TVs. Part of C-TECs patented Outreach Plate audio input extension system (see key features section below for details). Compatible with C-TECs entire range of PDA102, 200E, Pro-Rangeand ML1 induction loop amplifiers. Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply. Mounts on a 25mm standard UK single gang back box.

GBP 185.97
1

5x C-TEC 24V 250mA Door Release Power Supply Unit

5x C-TEC 24V 250mA Door Release Power Supply Unit

A compact Mains derived power supply unit designed to provide power to 24V DC electromagnetic door retainers. Maximum output 250mA. Trigger Release, Hold Off and Local Trigger Inputs facilitate straightforward connection to fire alarm control panels, building management systems, timers, relays and other ancillary equipment. Includes a manual release button, a Mains On and an Output Triggered indicator. Can be mounted on a standard 25mm UK double gang flush or surface back box.

GBP 214.95
1

3x C-TEC 6.35mm (1/4) Microphone Jack Plate

3x C-TEC 6.35mm (1/4) Microphone Jack Plate

Accepts balanced or unbalanced electret microphones with 6.35mm (1/4) jack plugs . Part of C-TECs patented Outreach Plate audio input extension system (see key features section below for details). Compatible with C-TECs entire range of PDA102, 200E, Pro-Rangeand ML1 induction loop amplifiers. Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply. Mounts on a 25mm standard UK single gang back box.

GBP 185.97
1

C-TEC Stainless Steel Single Zone Call Controller c/w 12V PSU

C-TEC Stainless Steel Single Zone Call Controller c/w 12V PSU

A high-quality brushedstainless steel single zone call controller c/w a 12V 250mA PSU. Fully compatible with C-TECs entire range of 800 Series Call System components. Capable of indicating standard (constant tone) and emergency (intermittent tone) calls. Power On and Alarm CALLING LEDs. Open collector output goes to 12V when the controllers onboard buzzer sounds. Mounts on a standard UK 40mm double gang flush or surface back box. Optional NC941B 0.3A battery battery backup kit also available.

GBP 179.99
1

4x C-TEC Master Infrared Ceiling Receiver

4x C-TEC Master Infrared Ceiling Receiver

A ceiling-mountable infrared receiver that will accept Standard & Emergency calls from compatible 800 Series infrared transmitters. Can receive line-of-sight infrared signals from around 10m away (dependent on physical conditions and environmental factors). Red reassurance LED confirms a call has been made. Requires a separate remote reset point such as our NC802DB button reset or NC899IRR keyswitch reset point for cancelling calls. Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 279.96
1

3x C-TEC APQL 6.35mm (1/4) Line Level Plate

3x C-TEC APQL 6.35mm (1/4) Line Level Plate

Accepts 6.35mm (1/4) jack feeds from audio equipment such as stage or church mixing desks, etc. Part of C-TECs patented Outreach Plate audio input extension system (see key features section below for details). Compatible with C-TECs entire range of PDA102, 200E, Pro-Rangeand ML1 induction loop amplifiers. Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply. Mounts on a 25mm standard UK single gang back box.

GBP 209.97
1

45x C-TEC Double Gang Surface Interface Plate, shallow (20mm)

45x C-TEC Double Gang Surface Interface Plate, shallow (20mm)

Allows standard UK double gang plated products to be fixed to most European style back boxes (square and round variants). Adapts to most European fixing centres see video for further details. Multiple variants available options include single gang shallow (NCP-23), single gang deep (NCP-24), double gang shallow (NCP-25) and double gang deep (NCP-26). Designed to match C-TECs existing plastics and colours. Tough and durable. Can also be surface mounted directly to a wall.

GBP 337.05
1

4x C-TEC Isolatable Monitoring Point, Button Reset

4x C-TEC Isolatable Monitoring Point, Button Reset

A keyswitch-isolatable monitoring point c/w magnetic door contacts for use with C-TECs 800 Series Call System. Can be used to monitor any device with a normally open or normally closed switch. Triggers a Standard call when activated Typical uses include monitoring fire exits, drug cupboards,store rooms, etc. Isolation keyswitch temporarily turns off the devices monitoring function whenin the ISOLATED position. Red reassurance LED illuminates when a call is made. Includes a RESET button for cancelling calls. Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 199.96
1

2x C-TEC 1.2m2 Double Gang Fixed Counter Induction Loop System

2x C-TEC 1.2m2 Double Gang Fixed Counter Induction Loop System

Ideal for banks, post offices, small meeting rooms, reception desks, ticket booths and any other application requiring restricted or small area coverage. Requires no specialist audio experience or connectors can be fitted by any competent electrician. Space-saving double-gang wall-mounting amplifier fits standard UK 25mm back boxes (requires fixed mains wiring). Omni-directional AMT microphone (supplied) plugs directly into the 3.5mm socket on the amplifiers front. Line/outreach socket also provided (max 3 outreach plates per system). User-adjustable mic. sensitivity and engineer-adjustable loop drive and input level controls.

GBP 299.98
1

3x C-TEC Four Zone Call Controller (requires NC930 12V 250mA PSU)

3x C-TEC Four Zone Call Controller (requires NC930 12V 250mA PSU)

An attractively-designed four zone call controller c/w mute and reset buttons. Fully compatible with C-TECs entire range of 800 Series Call System components. Capable of indicating standard (constant tone) and emergency (intermittent tone) calls. Requires a separate NC930 12V 250mA PSU. Includes four zonal alarm LEDs, RESET and MUTE buttons. Two open collector outputs (Emergency and Aux Out). Up to two NC944s can be connected to one NC930 PSU to create a mini-call system of up to 8 zones. Mounts on a standard 25mm UK double gang back box.

GBP 239.97
1