ProfitSpring | B2B PPC Agency

C-Tec ECU-224M Motherboard - 1-224 Line Desk Controller

C-Tec ECU-224M Motherboard - 1-224 Line Desk ControllerA replacement motherboard for the 1-224 Line Desk Controller.

GBP 173.09

1

C-Tec AMT Tie Desk Microphone

C-Tec AMT Tie Desk MicrophoneA microphone is perhaps the most important link in an audio chain. As the connection between the sound source and the sound system it must interact efficiently with both. Choosing this link successfully requires knowledge of the sound source the sound system including the room acoustics microphones and the actual application. The AMT is a tie desk microphone designed for the ML1 PDA102 PDA200 PL1 PDA-PRO or APJ plate.

GBP 8.32

1

C-Tec ECU-224 SigTEL 224 Line Desk Controller

C-Tec ECU-224 SigTEL 224 Line Desk ControllerOptional 1-224 line SigTEL Desk Controller with handset display. Requires an ECU723 fitted at an ECU-4 8 or 16 Controller. ECU-224s are NOT compatible with ECU-8NT Controllers.A new 224line Desk Controllerfor use with our SigTEL disabled refuge fire telephone and stadium marshallingsystem.Allows operators to communicate with up to 224disabled refuge or fire telephone outstations.Designed to simplify call-handling on larger EVC installations.Must be connected to an ECU-4 8 or 16 master controller viaan ECU-723 interfacenetwork card.Although designed to be free-standing an optional sloping wall mounting shelf is available order code ECUWMB.See schematicfull instructions for further details.

GBP 968.15

1

C-Tec QT42410 Ten-Way Charging Unit for QT412

C-Tec QT42410 Ten-Way Charging Unit for QT412The QT42410 ten-way charging unit can simultaneously charge up to ten QT412 Range dual action infraredradio transmitters. Designed to be powered from a 230V a.c. mains source using the standard IEC lead supplied the unit can be wall or desk mounted to suit the transmitter storage and charging requirements of a particular site.Key FeaturesA ten-way plugtop charger designed for use with Quantecs QT412 range of IRRF transmitters.Can simultaneously charge up to ten transmitters.Connects to a standard 13A mains socket using the standard IEC lead suppliedCan be wall or desk mounted to suit the transmitter storagecharging requirements of a particular site.Fully recharged transmitters can be left connected to the charger with no detrimental effect.14-hour typical charging time full cycle.Indicators confirm when charging is complete.

GBP 265.99

1

C-Tec ECU723 SigTEL InterfaceNetwork Communication Card

C-Tec ECU723 SigTEL InterfaceNetwork Communication CardECU-224 interfacenetwork card. Allows an ECU-224 desk controller to be connected to an ECU-4 8 or 16. Can also act as a network card if networking is required. NOT compatible with ECU-8NT Controllers.The ECU723 transmits speech via a single wiring loop and digital data via two linear RS485 networks. The network should be connected using 4 x 2-core 1.5 mm2 enhanced fire-rated cable. Max. length of all networks is 1 km.An optional system expansion device.Allows anECU-224 desk controller to be connected to an ECU-4 8or16 SigTEL controller to simplify call handling on larger SigTEL applications.Mounts inside an ECU-4 8 or 16 can alsobe used tonetworkthe ECU-4 8 or 16 to another controller if required.Not compatible with ECU-8NT controllers.See schematicfull instructions for further details

GBP 108.77

1

C-Tec ECU722 SigTEL Network Communication Card

C-Tec ECU722 SigTEL Network Communication CardNetwork card allows up to 14 ECU-4 8 16 or 8NTs to be interlinked. To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead.The ECU722 card transmits speech via a single wiring loop and digital data via two linear RS485 networks. The network should be connected using 4 x 2-core 1.5 mm2 enhanced fire-rated cable. Max. length of all networks is 1 km.Key FeaturesAn optional system expansion device.Allows up to 14 ECU-4 8 16 or 8NT SigTEL controllers to be interlinked.One card required per networked SigTEL controller.Allows systems of up to 224 lines 14x ECU-16controllers to be easily set-up.Any ECU-4ECU-8 or ECU-16 can take control of the system at any time by the input of a special code.Note that for networked systems that do not require multiple control points controllers without handsets are available ECU-8NT.IMPORTANT To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead of an ECU722 the ECU723 is due for release Nov 2019.

GBP 90.65

1

C-Tec 16 Line SigTEL Master Controller cw handset. Max 2 x 7Ah batteries ECU-16

C-Tec 16 Line SigTEL Master Controller cw handset. Max 2 x 7Ah batteries ECU-16Designed foruse with our popular SigTEL system the ECU-16 features a new-look high-performance handset to allow operators tocommunicate with up to 16 disabled refuge or firetelephone systems.The controllers powerful networking capabilities also allow up to 14ECU-16 mastercontrollers to be interlinked to create systems of up to224 lines. A separate ECU-224desk control unit can also be connectedtoallow communication with up to 224outstations from a single point.Compatible with C-TECs entire range of Type A Fire Telephone andType B Disabled Refugeoutstations and remote fire telephonehandsets the controller can be easilyinterfaced to NC951 accessibletoilet alarms PDA hearing loop systems strobesCCTV activation relaysand more.Key FeaturesA new 16-line Master Controller for use with our SigTEL disabled refuge fire telephone and stadium marshallingsystem.Allows operators to communicate with up to four disabled refuge or fire telephone outstations.Includes an attractive semi-recessed handset.Improved SigTEL networking capability allow systems of up to 224 lines to be created with optionaladditional desk unit control.Backlit LCD and unique auto-learn facility allows fast system set up.Can be semi-flush mounted using an AFP385 bezel.Operation can be maintained for 24 hours standby and 3 hours in use using 2 x 12V 7 Ahr batteries.Easily interfaced to NC951 accessible toilet alarms PDA range hearingloop systems strobes CCTV activation relays etc.

GBP 1906.25

1

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.64

1

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced microphones with standard 3 pin XLR connectors.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.30

1

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-Tecs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts unbalanced electret microphones with 3.5mm mono jack plugs.Part of C-Tecs patented Outreach Plate audio input extension system.Compatible with C-Tecs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.59

1

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.62

1

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm The Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced electret microphones with 6.35mm 14 jack plugs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57

1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57

1

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated MicrophoneThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesA self-contained omni-directional plated electret microphone complete with onboard mic to line level converter.Part of C-TECs patented Outreach Plate audio input extension system.Provides up to25m2 ambient coverage or 2.5m2 direct speechcoveragewhen located at a ceiling height of 2.5 to 3m.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 53.39

1

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesCombines the functions of anAPXM microphone Outreach plate and an APL dual phono Outreachplate in one double gang device.Accepts balanced or unbalanced microphones with standard 3 pin XLR connectors AND dual phono line level inputs.Gives a more attractive appearance than separate side-by-side single gang Outreach Plates.Counts as one of the total of ten plates permitted aspart of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK doublegang back box.

GBP 96.35

1

C-Tec CL1UK Mini Counter Hearing Loop Kit 1.2m2

C-Tec CL1UK Mini Counter Hearing Loop Kit 1.2m2Hearing loop systems allow hearing impaired people to hear more clearly. Most hearing aids have a T or MT switch which allows them to pick up the electromagnetic field generated by a hearing loop system. The hearing aid converts this signal into a sound suited to its users specific hearing requirements.Any person with a hearing aid positioned within or near the loop can hear the loop signal by switching their hearing aid to the correct position allowing them to participate more effectively in general conversation ordering goods or services listening to public performances etc.The C-Tec SigNET CL1UK mini counter induction loop system kit is the ideal high-quality stand-alone audio frequency induction loop system AFILS for a desk or counter application in a bank post office or ticket booth. The miniature loop amp generates a localised loop field ideal for one-to-one communication. The kit comes complete with loop amp power supply pre-formed counter loop microphone induction loop present sticker.Key FeaturesIdeal for banks post offices small meeting rooms reception desks ticket boothsand any other application requiring restricted or small area coverageGenerates a loop listening field of 4 sq.ft 1.2m2 Kit includes a compact CL1 mini-induction loop amplifier cw UL listed power supply an AMT microphone a TX121 pre-formed counter loop and AFILS available stickerAdjustable drive control level and line controls allows the amplifiers output stage to be set-up to suit the exact characteristics of the applicationMetal compensation control helps combat the frequency response problems caused by metal absorbing the magnetic fieldState-of-the-art audio processor features an automatic gain control which compensates for poor microphone techniques and helps suppress loud noises hisses and clicksDesigned to be free-standing or wall-mounted using the keyholes providedTechnical SpecificationsInduction Loop Type Wall mounting requires fixed mains wiring and a 25mm back boxCoverage 1.2m2 approx.Dimensions W 143 x H 83 x D 32mm 300g amplifier onlyInputs 1 x 3.5mm remote mic. socket 1 x LineOutreach socket max. 3 Outreach plates per ML1Indicators Input level power on loop drive meter.Controls Mic. input level line input level loop driveKit content ML1 amplifier AMT microphone TX2 pre-formed counter loop AFILS fitted sticker.

GBP 245.82

1

Brand

Merchant

Price (EUR)