49 results (0,14947 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Fireclass 517.300.021FC WT300 Walk-Test Controller

Fireclass 517.300.021FC WT300 Walk-Test Controller

Fireclass 517.300.021FC WT300 Walk-Test ControllerThe WT300 Walk-Test Tool is a hand-held unit for remotely activating the self-test features of the FV300 detectors. The unit is battery powered and can activate the alarm test window test or reset the FV300 detector from a range of over 6m by using an infra-red link.The WT300 can be used in hazardous areas. It is housed in a plastic enclosure with an anti-static coating. To prevent accidental operation the WT300 needs to be unlocked using the keypad before a command can be sent. It is an intrinsically safe unit and has been approved to use Duracell Procell MN1500 batteries only. No other types may be used in a hazardous area.In a safe area undo the two screws and remove the cover from the battery compartment. Remove the old batteries. Fit a pair of new batteries noting polarity as shown by markings in the bottom of the compartment. Refit the cover and secure with the screws. Dispose of old batteries considerately.Key FeaturesBattery powered using AA cellsUsed for remotely activating the self-test features of FV300 detectors

GBP 1640.86
1

Fireclass 516.800.923FC Service Accessory Kit FC Branded

Fireclass 516.800.923FC Service Accessory Kit FC Branded

Fireclass 516.800.923FC Service Accessory Kit FC BrandedThe 516.800.923FC is a Service Accessory Kit designed for use with the FC490ST Programmer. It is a plastic case complete with a shoulder strap and car ancillary power supply.The Fireclass Addressable Ancillary Smoke Detector Programmer Address Loop Service Tool FC490ST is a powerful and flexible loop service tool for assistance in smoke detector and ancillaries installation commissioning diagnostics and service of Fireclass fire detection systems.Key FeaturesPlastic case complete with shoulder strap and car ancillary power supplyFireclass brandedFor use with theFC490ST ProgrammerPlastic casePlease note Theimage is for illustrative purposes only. The Service Accessory Kit does not include the FC490ST programmer.

GBP 132.97
1

Fireclass Ceiling Tile Adaptor Kit

Fireclass Ceiling Tile Adaptor Kit

Fireclass Ceiling Tile Adaptor Kit 517.050.060FCThe Time Saver Ceiling Tile Adaptor is used with the 4B 4 detector base snap fit base and consists of three parts a bezel and clamp that are fitted to the ceiling tile and a back-box that carries the detector and base assembly. The Ceiling Tile Adaptor requires a 127mm diameter hole to be cut into the ceiling tile to allow an easy fit and flawless finish.Key FeaturesQuick and easy to installReduce installation time by up to 30Allows detector commissioning and testing before ceiling installationReduce installer injury risk

GBP 13.51
1

Fireclass 557.202.708FC FC410MIM Fixing Kit for FireClass 1.9A7Ah PSUs

Fireclass 557.202.708FC FC410MIM Fixing Kit for FireClass 1.9A7Ah PSUs

Fireclass 557.202.708FC FC410MIM Fixing Kit for FireClass 1.9A7Ah PSUsThe 557.202.708FC is a FC410MIM Addressable Mini Input Module and Fixing Kit designed for the Fireclass 1.9A7Ah Power Supply Units.The FC410MIM Mini Input module is designed to monitor fire contacts in extinguishing system control ventilation control fire door control etc. It is built for fitting in small devices that is required to be monitored for fire fault or warning.The module provides one identifiable detection spur which is capable of monitoring multiple normally open contacts or a single normally closed contact. The module can be mounted in any electrical enclosure with sufficient depth to accommodate it and the contacts monitored by the IN and IN- terminals. The remote LED if required not supplied must be located within the same electrical enclosure.Key FeaturesSupplied with fixing kitDesigned for us withFireclass 1.9A7Ah Power Supply UnitsSmall sizeOperating voltage 20 40V dcRelative Humidity Up to 95RH monitor100 OhmEnd Of Line Monitor Value 200 Ohm

GBP 95.87
1

Fireclass 509.030.121FC Extinguishing Hold Off Manual Call Point

Fireclass 509.030.121FC Extinguishing Hold Off Manual Call Point

Fireclass 509.030.121FC Extinguishing Hold Off Manual Call PointThe509.030.121FC is anExtinguishing Hold Off Manual Call Point with activation and end of line resistors making it compatible with the Prescient III Suppression Panel. Operation is via a non-latching push button. This call point is surface mounted and comes complete with back box test key.Key FeaturesColour BlueCompatible with thePrescient III Suppression PanelSurface mountComes with back box and test key

GBP 45.79
1

Fireclass FC490ST Handheld Service and Programming Tool

Fireclass FC490ST Handheld Service and Programming Tool

FC490ST Fireclass Handheld Service and Programming ToolThe FC490ST service tool used to address field devices from the Fireclass range.Key FeaturesReadWrite the detectorancillary addressDisplay temperatureCO levels and smoke obscurationProgramming of the LEDTesting the detector remote LED and control outputsPerform the detector self verification test functionDisplay detector contamination levelControlling ancillary outputsReading ancillary statusPower management options

GBP 305.51
1

Fireclass 2501234FC Conventional Manual Call Point with Plastic Element with Back Box

Fireclass 2501234FC Conventional Manual Call Point with Plastic Element with Back Box

Fireclass 2501234FC Conventional Manual Call Point with Plastic Element with Back BoxA conventional manual alarm call point with integral alarm LED and activation resistor. Operation is by resettable deformable element.This call point is semi flush mounted or can be surface mounted using back box and comes complete with a test key.Fireclass has comprehensive range of callpoints for use with conventional systems.Key FeaturesDistinctive and recognisable stylingSurface or Flush MountingTest key facility speeds maintenance visits

GBP 13.97
1