ProfitSpring | B2B PPC Agency

Notifier S300PTU Programming Test Unit for PhD Detectors

Notifier S300PTU Programming Test Unit for PhD DetectorsThe S300PTU is a hand-held Programming Test Unit for use with the PhD range of conventional detectors.Communication is achieved via an LED and opto-diode built in to the S300PTU for close range communication. This allows direct communication via the detector LED indicator.Key FeaturesLED and opto-diode built inDesigned for use with the PhD range of conventional detectors

GBP 361.80

1

Notifier SC070 Pack Of Test Keys Pack of 10

Notifier SC070 Pack Of Test Keys Pack of 10A pack of spare keys for use with KAC break glass call points.Key FeaturesPack of 10

GBP 6.17

1

Notifier NFXI-BEAM-T Loop Powered Beam Detector with Test Facility

Notifier NFXI-BEAM-T Loop Powered Beam DetectorThe Opal addressable beam detector is an intelligent reflector type linear optical beam smoke detector designed to operate with Notifier addressable fire alarm systems. It operates primarily on the principle of light obscuration utilising infra-red light. The Infra-Red transmitter generates a beam of light towards a high efficiency reflect. The reflector returns the beam to the receiver where an analysis of the received signal is made. The change in the strength of the received signal is used to determine the alarm condition.Key Features5 100m operating range designed for the protection of buildings such as shopping centres heritage buildings warehouses and other structures with large open spacesEasy set-up and calibration with visual aids for both coarse and fine adjustmentLoop powered with built in isolation for system mappingUtilizes the advanced Opal digital protocol whilst remaining backward compatible with existing Notifier systemThe NFXI-BEAM-T Beam Detector features a unique remote test capability that fully tests both the optics and the electronics of the device. This means theres no need to hire a platform to give high level access to the device in testing.Two automatically variable sensitivity modes compensate for short term environmental changesAutomatic drift compensation compensates for long term sensitivity changes caused by environmental factorsFour fixed sensitivity level

GBP 1026.98

1

Notifier IDR-6A Active Repeater Panel Stainless Steel 002-466

Notifier IDR-6A Active Repeater Panel Stainless Steel 002-466The IDR-2A active repeater will repeat the LCD LED indications on the main fire alarm panel and allow the operator to command the system using system control pushbuttons Mute Buzzer Accept Evacuate Silence Sounders Resound Sounders and Reset. Furthermore the IDR-2A has configuration and test functions such as edit Normal message Lamp Test LCD Test Buzzer Test and a Pushbutton Test option.For added security a key-switch on the front of the repeater enablesdisables certain push buttons. The nine LED indicators provide a quick summary of the general system status for the user. The compact design makes it very easy to install and commission the IDR Series repeaters. The repeaters event log can store up to 150 most recent events this also aids commissioning.Key FeaturesQuickly identify the location of a fire related incidentDesigned to comply with EN54 Part 2Simple connection to ID panelsActive Passive optionsPower diagnosticsPush button testLanguage optionsWindows based off-line configuration tool

GBP 1451.23

1

Notifier IDR2-A Active Repeater Panel For ID50 ID60 amp ID2000

Notifier IDR2-A Active Repeater Panel For ID50 ID60 ID2000The IDR-2A active repeater will repeat the LCD LED indications on the main fire alarm panel and allow the operator to command the system using system control pushbuttons Mute Buzzer Accept Evacuate Silence Sounders Resound Sounders and Reset. Furthermore the IDR-2A has configuration and test functions such as edit Normal message Lamp Test LCD Test Buzzer Test and a Pushbutton Test option.For added security a key-switch on the front of the repeater enablesdisables certain push buttons. The nine LED indicators provide a quick summary of the general system status for the user. The compact design makes it very easy to install and commission the IDR Series repeaters. The repeaters event log can store up to 150 most recent events this also aids commissioning.Key FeaturesQuickly identify the location of a fire related incidentDesigned to comply with EN54 Part 2Simple connection to ID panelsActive Passive optionsPower diagnosticsPush button testLanguage optionsWindows based off-line configuration tool

GBP 855.82

1

Notifier Compact Mimic Main Board Kit PRL-MIMIC

Notifier Compact Mimic Main Board Kit PRL-MIMICCompatible with Pearl Panels.16 outputs on board and up to 9 expansion boards 020-742 can be added drive LEDs or relays giving maximum of 160 outputs. 5 LED outputs power ok Test Gen. Fault Disablement Fire and 6 Inputs Key switch Evacuate Mute Buzzer Silence Sounders Lamp Test Reset. Requires ext. 24VDC Power Source. For use with Local Zones.

GBP 394.25

1

Notifier ID3000 Extension Chassis Kit 020-559-001 Zone 1 to 65

Notifier ID3000 Extension Chassis Kit 020-559-001 Zone 1 to 65Extension chassis with Led display board for zone 1 to 65 to indicate fire and fault disablement test. Will also accept integral printer.

GBP 268.51

1

Notifier ID3000 Extension Chassis Kit 020-559-002 Zone 65 to 128

Notifier ID3000 Extension Chassis Kit 020-559-002 Zone 65 to 128Extension chassis with Led display board for zone 65 to 128 to indicate fire and fault disablement test. Will also accept integral printer.

GBP 308.26

1

Notifier 843090-0210 Bose FreeSpace 3 Series II Acoustimass Bass Module - White - Flush Mount

Notifier 843090-0210 Bose FreeSpace 3 Series II Acoustimass Bass Module - White - Flush MountDesigned to provide flush-mount bass augmentation for new and existing background music systems. Features one 5.25 133 mm woofer that delivers deep bass down to 40 Hz without audible distortion.For indoor applications only.Key FeaturesLow-frequency loudspeaker featuring one 5.25 133 mm woofer that delivers deep non-localized bass support down to 40 Hz without audible distortion. For flush ceiling pendant and wall-mount applicationsAcoustimass speaker technology filters out audible distortion to deliver non-localized bassDesigned to work with the FreeSpace 3 flush and surface satellite speakers or existing systems where additional bass reinforcement is desiredModule design allows parallel connection of multiple bass modules and can accommodate two or four FreeSpace 3 satellites per bass modulePlenum rated for use in air handling spaces with optional plenum coverSelectable 70100V or low impedance with transformer tap adjustment under speaker grille

GBP 1067.26

1

Notifier ECO1003A ECO Photoelectric Smoke Detector

Notifier ECO1003A ECO Photoelectric Smoke DetectorThe ECO1003 A photoelectric smoke detector belongs to System Sensors ECO1000 range of detectors. ECO1000 is a range of conventional detectors which have been produced using the latest in manufacturing technology and supplied with an array of advanced features making them better by design.The ECO1003 A photoelectric smoke detector uses a state of the art optical chamber combined with an application specific integrated circuit ASIC to provide quick and accurate detection of fires. A combination of the unique chamber design and other technically advanced features will significantly extend the service intervals before cleaning of the detector becomes necessary.A laser-based hand held Remote Test Unit can be used in conjunction with the range of ECO1000 detectors for alarm test purposes. The unit transmits a coded message preventing spurious alarms being generated by other laser-based devices. With a range of several metres the hand held test unit provides a fast and simple way of remotely alarm testing the range of ECO1000 detectors and removes the need for any direct physical access to the detector by the useThe ECO1003 A detector has an integral LED which illuminates to provide a local alarm signal. This latches on and remains illuminated until the detector is reset by a momentary power interruption. An optional remote LED annunciator may be used to repeat any alarm signal.A variety of detector bases can be used with the ECO1003 A detector providing application flexibility and compatibility with a wide range of Fire Alarm Control Panels. All bases are fitted with a shorting spring to permit circuit testing prior to fitting the detector and have a tamper resistant feature which when activated prevents removal of the detector without the use of a tool. All System Sensor products are covered by our extended 3-year warranty.Key FeaturesLow profile designLow current drawAutomatic drift compensationOperates on 12 and 24VDC SystemsRemote alarm test featureEasy MaintenanceApproved to EN54 72000Approved to MED 9698ECExtended warranty

GBP 23.45

1

Notifier 020-741 IDR-CM Compact Mimic Driver

Notifier 020-741 IDR-CM Compact Mimic DriverThe Compact Mimic is an expandable mimic suitable for standard or more complex applications where mimic displays are required in association with NOTIFIER fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a keyswitch input to enable evacuate silence lamp test mute and reset inputs.The Compact Mimic has two types of boards a main board IDR-CM and an expansion board IDR-CME both of which can have up to 16 configurable outputs. A fully utilized compact mimic system can comprise one main board and up to 9 expansion boards providing a maximum total of 160 configurable outputs.

GBP 428.32

1

Notifier 020-742 IDR-CME Compact Mimic Expansion Board

Notifier 020-742 IDR-CME Compact Mimic Expansion BoardThe Compact Mimic is an expandable mimic suitable for standard or more complex applications where mimic displays are required in association with NOTIFIER fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a keyswitch input to enable evacuate silence lamp test mute and reset inputs.The Compact Mimic has two types of boards a main board IDR-CM and an expansion board IDR-CME both of which can have up to 16 configurable outputs. A fully utilized compact mimic system can comprise one main board and up to 9 expansion boards providing a maximum total of 160 configurable outputs.

GBP 137.09

1

Notifier 020-573 IDR-M Mimic Control PCA Kit

Notifier 020-573 IDR-M Mimic Control PCA KitThe IDR-M Mimic Driver is part of a versatile system where mimic displays are required in association with Notifier fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a key switch input to enable evacuate silence lamp test mute and reset inputs.The IDR-M Control and Termination kit comprises a Control board and a Termination board co-located on one metal chassis. The Control board contains the processor and memory and the Termination board allows connection of power RS485 and other external signals. The Control board communicates with up to eight Mimic Driver boards.

GBP 565.40

1

Notifier 020-574 IDR-MD Mimic Driver amp Termination Board PCA Kit

Notifier 020-574 IDR-MD Mimic Driver Termination Board PCA KitThe IDR-M Mimic Driver is part of a versatile system where mimic displays are required in association with Notifier fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a key switch input to enable evacuate silence lamp test mute and reset inputs.The IDR-M Control and Termination kit comprises a Control board and a Termination board co-located on one metal chassis. The Control board contains the processor and memory and the Termination board allows connection of power RS485 and other external signals. The Control board communicates with up to eight Mimic Driver boards.

GBP 903.67

1

Notifier ID3000 256 Zone LED Display Extension Kit 020-612

Notifier ID3000 256 Zone LED Display Extension Kit 020-612Includes 2 extension chassis with LED display boards for zones 1 to 256 to indicate fire fault disablement test. Requires double extended backbox standard or deep and 256 Zone extension cover kits 020-621-009. A printer module 020-471 cannot be added with this option.

GBP 986.42

1

Notifier FSP-851 Smoke - Automatic Fire Detector Head

Notifier FSP-851 Smoke - Automatic Fire Detector HeadThe FSP-851 is plug-in type smoke sensor that combines a photoelectronic sensing chamber with addressable-analogue communications. The sensors transmit an analogue representation of smoke density over a communication line to a control panel. Rotary decade switches are provided for setting the sensors address. Two LEDs on the sensor are controlled by the panel to indicate sensor status.An output is provided for connection to an optional remote LED annunciator PN RA400ZRA100Z.Key FeaturesSleek low-profile designAddressable-analogue communicationStable communication technique with noise immunityLow standby currentTwo-wire SLC connectionCompatible with FlashScan and CLIP protocol systemsRotary decimal addressing 1-99 on CLIP systems 1-159 on FlashScan systemsOptional remote single-gang LED accessoryDual LED design provides 360 viewing angleVisible bi-colour LEDs blink green every time the detector is addressed and illuminate steady red on alarm FlashScan systems onlyRemote test feature from the panelWalk test with address display an address on 121 will blink the detector LED 12-pause-1 FlashScan systems onlyBuilt-in functional test switch activated by external magnetBuilt-in tamper-resistant featureSealed against back pressureConstructed of off-white fire-resistant plastic designed to commercial standards and offers an attractive appearance94-5V plastic flammability ratingSEMS screws for wiring of the separate baseLegacy product

GBP 55.13

1

Notifier NFS3-EXT Single Area 3 Zone Extinguishant Control Panel

Notifier NFS3-EXT Single Area 3 Zone Extinguishant Control PanelDesigned and manufactured to the highest standards with European EN120941 approval the NFS3EXT extinguishing releasing panel offers outstanding value and performance for all small to medium fixed fire fighting installations. With three detection zones as standard extinguishing release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three type activations such as would be required for detection in ceiling void room and floor void applications.Key FeaturesThree detection zonesComplies with EN12094-1 and EN54-2 4Configurable input combinationsConfigurable delay optionsConfigurable non latching zoneConfigurable extinguishing duration timerCount down timer displayFull remote repeaterOptional Auxiliary IO boardExtract fan control

GBP 881.77

1

Notifier ECO Photoelectric Smoke Temperature Detector ECO1002A

Notifier ECO Photoelectric Smoke Temperature Detector ECO1002ASmoke and photoelectric thermal detector consists of an optical chamber sensitive to light scattering and a thermistor sensitive to heat. Alarm LED. Output for alarm repeater. Ready to test via remote control laser. CPD Certificate in accordance with EN 54 parts 5 and 7. 8-28VDC power supply. Operating temperature -20C to 60C. Relative humidity up to 95 non-condensing.Key FeaturesLow profile designLow current drawAutomatic drift compensationOperates on 12 and 24vdc systemsEasy maintenanceApproved to EN54-7Approved to MED 9698ECExtended warranty

GBP 32.62

1

Notifier SD-851EA PhD Low-Profile 800 Series Conventional Optical Smoke Detector

Notifier SD-851EA PhD Low-Profile 800 Series Conventional Optical Smoke DetectorPhD low profile 800 Series conventional optical smoke detector. The SD-851E photoelectric smoke detector incorporates an optical chamber which is continually monitored by an on board processor which uses algorithms developed specifically for the unit. An alarm signal is only enabled in the detector once the processor is satisfied that a real fire has been detected thereby reducing the incidence of nuisance alarms.A variety of detector bases are available providing compatibility with a wide range of Fire Alarm Control Panels making it ideal for expansions and retrofit applications. The remote hand-held programming tool can also be used in conjunction with the PhD series of detectors to gain access to other enhanced features. The features available include readwrite last maintenance date read chamber contamination level read value of thermal element and perform an alarm test.Key FeaturesAutomatic drift compensationProgrammable SensitivityAdvanced maintenance features via remote hand-held test unitLow profile designLow current drawWide operating voltage 8 to 30VDCBi-colour LED detector status indicatorAddressable alarm location featureApproved to EN54 part 7 20003 year warrantyComes with a PROGRAMMABLE feature set removable cover insect screen LASER test and device status transmission to handheld programmer

GBP 36.42

1

Notifier BRS-PC-I02 Standard Power Addressable Base Sounder Strobe NFXI-BSF-WCS

Notifier BRS-PC-I02 Standard Power Addressable Base Sounder Strobe NFXI-BSF-WCSThe Notifier NFXI-BSF-WCS is a standard power addressable base sounder strobe for use on Notifier protocol analogue addressable fire alarm panels.Key FeaturesRed FlashPure White BodyClear Lens cw IsolatorLoop-powered EN54-23 C Category - Standard Performance Detector Base Sounder StrobeEN54-23 certifiedCoverage volume code C-3-8.5 Standard O-1-3 Legacy

GBP 72.91

1

Notifier BRH-PC-I02 High Performance Detector Base Sounder Strobe NFXI-BSF-WCH

Notifier BRH-PC-I02 High Performance Detector Base Sounder Strobe NFXI-BSF-WCHThe Notifier NFXI-BSF-WCH is a high performance addressable base sounder strobe for use on Notifier protocol analogue addressable fire alarm panels.Key FeaturesRed FlashPure White BodyClear Lens cw IsolatorLoop-powered EN54-23 C Category - High Performance Detector Base Sounder StrobeEN54-23 certifiedCoverage volume code C-3-15 High C-3-11 Low C O-1-4 Legacy

GBP 89.04

1

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242Four-channel power amplifier with built in battery charger for emergency power supply of VARIODYN D1 Comprio. 4XD125B has 4 independent amplifier channels each with 125 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB models. The amplifier may be used with the VARIODYN D1 Comprio as well as a DOM. It is also possible to use the amplifier with a separate PSU in this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelOne height unitIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 65 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 3463.82

1

Notifier ID3002 2 Loop Intelligent Fire Alarm Control Panel

Notifier ID3002 2 Loop Intelligent Fire Alarm Control PanelThe Notifier ID3000 family of fire alarm control panels deliver the power and flexibility to meet the even the most demanding of requirements. From 2 to 8 loops in a single ID3000 panel to over 500 loops on a network an ID3000 system offers unrivalled stability versatility and capacity. When it comes to giving you the earliest possible warning of a potential fire threat the ID3000 supports Notifiers comprehensive range of detectors advanced fire detection sensors and loop devices delivering you the most complete and versatile fire alarm system in the market place.The ID3000 can be programmed to adapt to the different uses of the areas where smoke detectors are installed. A total of 9 different sensitivity levels can be assigned to individual smoke sensors thereby allowing the system designer to closely match the sensors response to the environment in which the device is located. This even allows smoke detection to be turned off leaving heat detection active.Key Features2-8 Analogue Addressable Loops each of up to 198 devices255 Fire zones per panelFully approved peer to peer network of up to 63 panels maintains 3 second call point response time over the networkFlexible timer functions system sensitivity and functionality can be tailored for the time of day or day of weekSophisticated cause and effect programming including support for non-fire signals and over-ride capability for smoke control systems.Convenience features for commissioning and maintenance engineers such as auto-learn of loops walk test and double address detection.CPD approved by LPCB BRE VdS

GBP 2933.30

1

Notifier M5A-RP02FG-N026-01 Addressable Call Point cw Isolator

Notifier M5A-RP02FG-N026-01 Addressable Call Point cw IsolatorThis Notifier Manual Call Point Break Glass Unit M5A-RP02FG-N026-01 is specifically designed to be used on Notifier Protocol Fire Alarm Control Panels. The unit is designed to give a manual signal to the Notifier Fire Alarm Control panel which will operate the fire alarm system.This unit features an integral loop isolator built into the device.These units are based on the industry standard KAC manual call point. They have been designed specifically to give installation efficiency flexibility and compliance with the latest standards.The Notifier Manal Call Point Break Glass M5A-RP02FG-N026-01 features an Integral LED. This LED will illuminate once the break glass unit has been operated. This feature allows easy identification as to which Notifier Manual Call Point Break Glass has been operated.The Notifier Manual Call Point Break Glass Unit features a unique plug and play concept that is designed specifically to reduce installation time by using a terminal block which can be wired during the initial installation cabling with a link to provide continuity for testing. During the commissioning phase the links are removed and the terminal block is simply inserted into the connector at the back of the unit. No re-termination is required.This Notifier Manual Call Point uses one of 99 possible addresses which is simply dialled in using the two rotary decade switches on the rear of the unit.A specialist test key may be inserted into the bottom of the unit to lower the glass and release the micro-switch and thus a full functional test is achieved.It is supplied as a flush mounting unit. It requires a single gang back box for surface mounting not included.Key FeaturesGlass includedRequires PS031W for surface-mounting terminal tray TB011 and single gang backbox for semi-flushing mountingUnique plug and play installation conceptFlush Mounted Call Point requires backbox for Surface Mounting Please see related products belowResettable plastic element option available not includedNotifier Analogue Addressable Protocol CommunicationsFully compliant with EN54 Part 11Backward CompatibleEnhanced AestheticsIntegral LEDIntegral Isolator

GBP 61.66

1

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243Four-channel amplifier with integrated battery recharging system for the emergency power supply to the VARIODYN D1 Comprio. The 4XD250B features 4 independent amplifier channels each with 250 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB and 4XDxxxW models. The amplifier can be used in combination with the VARIODYN D1 Comprio as well as with a DOM. It is also possible to use the amplifier also with a separate PSU the internal PSU must be switched of then. In this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelTwo Height Unit 2 HUIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 105 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 5451.26

1

Brand

Merchant

Price (EUR)