47 results (0,19402 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Pferd POS Wheel Brush Wide Crimped RBU Diameter 250X30XVARIABLE Hole Stainless Steel Wire Diameter 0.30 Bench Grinder

Pferd POS Wheel Brush Wide Crimped RBU Diameter 250X30XVARIABLE Hole Stainless Steel Wire Diameter 0.30 Bench Grinder

Excellent for medium-duty hand-held or automated brushing of workpieces with large surfaces. In order to fulfil the particular requirements for working with stainless steel (INOX), PFERD uses wire quality 1.4310 (V2A) for all INOX brushes. Practical experience from industry has shown that this offers very good corrosion resistance with an optimum tool life. All PFERD brushes with INOX filaments are colour-coded in blue and are suitable for use on all stainless steels (INOX), such as V4A. The wire quality 1.4310 tends to become ferromagnetic in the case of cold working; i.e. it can be attracted using magnets.;The reason for this is a change in the microstructure caused by deformation (e.g. during the wire drawing process). This does not have any impact on the quality and corrosion resistance of the INOX filament. The filament is still resistant to corrosion. Stainless steel wire (INOX) withstands temperatures up to 450 C. Developed for general use in the workshop.

GBP 159.99
1

10x Pferd POS End Brush Crimped PBU Diameter 15 mm Shank Diameter 6 mm Stainless Steel Wire Diameter 0.20

10x Pferd POS End Brush Crimped PBU Diameter 15 mm Shank Diameter 6 mm Stainless Steel Wire Diameter 0.20

Suitable for light brushing such as deburring, cleaning and derusting. End brush with plastic-covered brush body. In order to fulfil the particular requirements for working with stainless steel (INOX) , PFERD uses wire quality 1.4310 (V2A) for all INOX brushes. Practical experience from industry has shown that this offers very good corrosion resistance with an optimum tool life. All PFERD brushes with INOX filaments are colour-coded in blue and are suitable for use on all stainless steels (INOX) , such as V4A. The wire quality 1.4310 tends to become ferromagnetic in the case of cold working; i.e. it can be attracted using magnets.;The reason for this is a change in the microstructure caused by deformation (e.g. during the wire drawing process) This does not have any impact on the quality and corrosion resistance of the INOX filament. The filament is still resistant to corrosion. Stainless steel wire (INOX) withstands temperatures up to 450 C.

GBP 149.90
1

10x Pferd Twist Drill SPB DIN338 HSSG N 12.8mm Steel

10x Pferd Twist Drill SPB DIN338 HSSG N 12.8mm Steel

Spiral drill STEEL dia. 12.8 mm HSS-G N DIN 338 118 universal Angle118 Diameter12.8 mm Flute length101 mm Length, total151 mm RPM from, grey cast iron, white cast iron249 RPM RPM from, hard non-ferrous metals622 RPM RPM from, soft non-ferrous metals746 RPM RPM from, steels over 700 N/mm498 RPM RPM from, steels up to 700 N/mm622 RPM RPM from, thermoplastics, fibre-reinforced plastics (GRP/CRP) 373 RPM RPM to, grey cast iron, white cast iron622 RPM RPM to, hard non-ferrous metals1244 RPM RPM to, soft non-ferrous metals1493 RPM RPM to, steels over 700 N/mm622 RPM RPM to, steels up to 700 N/mm871 RPM RPM to, thermoplastics, fibre-reinforced plastics (GRP/CRP) 995 RPM Spiral angle, from25 Spiral angle, to30 VersionSTEEL Packaging unit5 pieces Drilling tools with cross grinding for industrial uses. Fully ground, right-hand turning versions that produce precise drill holes thanks to their high concentricity and exact centring. PFERD offers spiral drills in the STEEL (118 point angle) and INOX (135 point angle) versions. High-performance drilling tools in the STEEL in HSSG (M2) version for industrial uses. Fully ground right-hand turning version with cross grinding that produces precise drill holes thanks to their high concentricity and exact centring. Advantages Very good chip removal. High concentricity. Exact centring and low feed force thanks to cross grinding. Suitable for general use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminium. Easy centring. Long tool life. Recommendations for use Observe the recommended rotational speeds. When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill tool life. Exception: when working on aluminium, use kerosene instead of cutting oil. When working on stainless steel (INOX) , remove any particles that break away from the workpiece in order to avoid corrosion. Clean the workpiece chemically or mechanically (etching/polishing, etc.) . Safety notes Wear eye protection! Follow the safety instructions! Materials that can be worked Aluminium Annealed cast iron Black annealed cast iron (GTS, GJMB) Brass Bronze Case-hardened steels Casting scale Casting scale with sand contamination and metal contamination Cast iron Cast steel Chipboard Copper Ductile cast iron Elastomers Fibre-reinforced thermosetting plastics (GRP, CRP) Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 % Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content 40 % Grey/nodular cast iron (GG/GJL, GGG/GJS) Hard non-ferrous metal Hardwood Other Other non-ferrous metals Plastics Roller-bearing and ball-bearing steels Soft non-ferrous metal Soft titanium alloys (tensile strength 500 N/mm) Soft wood Steel Steel, cast steel Steels over 700 N/mm (> 220 HB) Steels up to 1, 200 N/mm (< 38 HRC) Steels up to 700 N/mm (< 220 HB) Thermoplastics Thermosetting plastics Titanium Titanium alloys Tool steels White annealed cast iron (GTW, GJMW) Wood Zinc Applications Drilling Drive types Column drill Power drill Robot Stationary machines Tool machine

GBP 89.90
1

10x Pferd Twist Drill SPB DIN338 HSSG N 12.7mm Steel

10x Pferd Twist Drill SPB DIN338 HSSG N 12.7mm Steel

Spiral drill STEEL dia. 12.7 mm HSS-G N DIN 338 118 universal Angle118 Diameter12.7 mm Flute length101 mm Length, total151 mm RPM from, grey cast iron, white cast iron251 RPM RPM from, hard non-ferrous metals627 RPM RPM from, soft non-ferrous metals752 RPM RPM from, steels over 700 N/mm502 RPM RPM from, steels up to 700 N/mm627 RPM RPM from, thermoplastics, fibre-reinforced plastics (GRP/CRP) 376 RPM RPM to, grey cast iron, white cast iron627 RPM RPM to, hard non-ferrous metals1254 RPM RPM to, soft non-ferrous metals1505 RPM RPM to, steels over 700 N/mm627 RPM RPM to, steels up to 700 N/mm878 RPM RPM to, thermoplastics, fibre-reinforced plastics (GRP/CRP) 1003 RPM Spiral angle, from25 Spiral angle, to30 VersionSTEEL Packaging unit5 pieces Drilling tools with cross grinding for industrial uses. Fully ground, right-hand turning versions that produce precise drill holes thanks to their high concentricity and exact centring. PFERD offers spiral drills in the STEEL (118 point angle) and INOX (135 point angle) versions. High-performance drilling tools in the STEEL in HSSG (M2) version for industrial uses. Fully ground right-hand turning version with cross grinding that produces precise drill holes thanks to their high concentricity and exact centring. Advantages Very good chip removal. High concentricity. Exact centring and low feed force thanks to cross grinding. Suitable for general use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminium. Easy centring. Long tool life. Recommendations for use Observe the recommended rotational speeds. When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill tool life. Exception: when working on aluminium, use kerosene instead of cutting oil. When working on stainless steel (INOX) , remove any particles that break away from the workpiece in order to avoid corrosion. Clean the workpiece chemically or mechanically (etching/polishing, etc.) . Safety notes Wear eye protection! Follow the safety instructions! Materials that can be worked Aluminium Annealed cast iron Black annealed cast iron (GTS, GJMB) Brass Bronze Case-hardened steels Casting scale Casting scale with sand contamination and metal contamination Cast iron Cast steel Chipboard Copper Ductile cast iron Elastomers Fibre-reinforced thermosetting plastics (GRP, CRP) Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 % Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content 40 % Grey/nodular cast iron (GG/GJL, GGG/GJS) Hard non-ferrous metal Hardwood Other Other non-ferrous metals Plastics Roller-bearing and ball-bearing steels Soft non-ferrous metal Soft titanium alloys (tensile strength 500 N/mm) Soft wood Steel Steel, cast steel Steels over 700 N/mm (> 220 HB) Steels up to 1, 200 N/mm (< 38 HRC) Steels up to 700 N/mm (< 220 HB) Thermoplastics Thermosetting plastics Titanium Titanium alloys Tool steels White annealed cast iron (GTW, GJMW) Wood Zinc Applications Drilling Drive types Column drill Power drill Robot Stationary machines Tool machine

GBP 89.90
1

10x Pferd Twist Drill SPB DIN338 HSSG N 12.9mm Steel

10x Pferd Twist Drill SPB DIN338 HSSG N 12.9mm Steel

Spiral drill STEEL dia. 12.9 mm HSS-G N DIN 338 118 universal Angle118 Diameter12.9 mm Flute length101 mm Length, total151 mm RPM from, grey cast iron, white cast iron247 RPM RPM from, hard non-ferrous metals617 RPM RPM from, soft non-ferrous metals741 RPM RPM from, steels over 700 N/mm494 RPM RPM from, steels up to 700 N/mm617 RPM RPM from, thermoplastics, fibre-reinforced plastics (GRP/CRP) 370 RPM RPM to, grey cast iron, white cast iron617 RPM RPM to, hard non-ferrous metals1234 RPM RPM to, soft non-ferrous metals1481 RPM RPM to, steels over 700 N/mm617 RPM RPM to, steels up to 700 N/mm864 RPM RPM to, thermoplastics, fibre-reinforced plastics (GRP/CRP) 988 RPM Spiral angle, from25 Spiral angle, to30 VersionSTEEL Packaging unit5 pieces Drilling tools with cross grinding for industrial uses. Fully ground, right-hand turning versions that produce precise drill holes thanks to their high concentricity and exact centring. PFERD offers spiral drills in the STEEL (118 point angle) and INOX (135 point angle) versions. High-performance drilling tools in the STEEL in HSSG (M2) version for industrial uses. Fully ground right-hand turning version with cross grinding that produces precise drill holes thanks to their high concentricity and exact centring. Advantages Very good chip removal. High concentricity. Exact centring and low feed force thanks to cross grinding. Suitable for general use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminium. Easy centring. Long tool life. Recommendations for use Observe the recommended rotational speeds. When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill tool life. Exception: when working on aluminium, use kerosene instead of cutting oil. When working on stainless steel (INOX) , remove any particles that break away from the workpiece in order to avoid corrosion. Clean the workpiece chemically or mechanically (etching/polishing, etc.) . Safety notes Wear eye protection! Follow the safety instructions! Materials that can be worked Aluminium Annealed cast iron Black annealed cast iron (GTS, GJMB) Brass Bronze Case-hardened steels Casting scale Casting scale with sand contamination and metal contamination Cast iron Cast steel Chipboard Copper Ductile cast iron Elastomers Fibre-reinforced thermosetting plastics (GRP, CRP) Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 % Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content 40 % Grey/nodular cast iron (GG/GJL, GGG/GJS) Hard non-ferrous metal Hardwood Other Other non-ferrous metals Plastics Roller-bearing and ball-bearing steels Soft non-ferrous metal Soft titanium alloys (tensile strength 500 N/mm) Soft wood Steel Steel, cast steel Steels over 700 N/mm (> 220 HB) Steels up to 1, 200 N/mm (< 38 HRC) Steels up to 700 N/mm (< 220 HB) Thermoplastics Thermosetting plastics Titanium Titanium alloys Tool steels White annealed cast iron (GTW, GJMW) Wood Zinc Applications Drilling Drive types Column drill Power drill Robot Stationary machines Tool machine

GBP 89.90
1

10x Pferd Twist Drill SPB DIN338 HSSG N 12.6mm Steel

10x Pferd Twist Drill SPB DIN338 HSSG N 12.6mm Steel

Spiral drill STEEL dia. 12.6 mm HSS-G N DIN 338 118 universal Angle118 Diameter12.6 mm Flute length101 mm Length, total151 mm RPM from, grey cast iron, white cast iron253 RPM RPM from, hard non-ferrous metals632 RPM RPM from, soft non-ferrous metals758 RPM RPM from, steels over 700 N/mm506 RPM RPM from, steels up to 700 N/mm632 RPM RPM from, thermoplastics, fibre-reinforced plastics (GRP/CRP) 379 RPM RPM to, grey cast iron, white cast iron632 RPM RPM to, hard non-ferrous metals1264 RPM RPM to, soft non-ferrous metals1517 RPM RPM to, steels over 700 N/mm632 RPM RPM to, steels up to 700 N/mm885 RPM RPM to, thermoplastics, fibre-reinforced plastics (GRP/CRP) 1011 RPM Spiral angle, from25 Spiral angle, to30 VersionSTEEL Packaging unit5 pieces Drilling tools with cross grinding for industrial uses. Fully ground, right-hand turning versions that produce precise drill holes thanks to their high concentricity and exact centring. PFERD offers spiral drills in the STEEL (118 point angle) and INOX (135 point angle) versions. High-performance drilling tools in the STEEL in HSSG (M2) version for industrial uses. Fully ground right-hand turning version with cross grinding that produces precise drill holes thanks to their high concentricity and exact centring. Advantages Very good chip removal. High concentricity. Exact centring and low feed force thanks to cross grinding. Suitable for general use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminium. Easy centring. Long tool life. Recommendations for use Observe the recommended rotational speeds. When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill tool life. Exception: when working on aluminium, use kerosene instead of cutting oil. When working on stainless steel (INOX) , remove any particles that break away from the workpiece in order to avoid corrosion. Clean the workpiece chemically or mechanically (etching/polishing, etc.) . Safety notes Wear eye protection! Follow the safety instructions! Materials that can be worked Aluminium Annealed cast iron Black annealed cast iron (GTS, GJMB) Brass Bronze Case-hardened steels Casting scale Casting scale with sand contamination and metal contamination Cast iron Cast steel Chipboard Copper Ductile cast iron Elastomers Fibre-reinforced thermosetting plastics (GRP, CRP) Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 % Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content 40 % Grey/nodular cast iron (GG/GJL, GGG/GJS) Hard non-ferrous metal Hardwood Other Other non-ferrous metals Plastics Roller-bearing and ball-bearing steels Soft non-ferrous metal Soft titanium alloys (tensile strength 500 N/mm) Soft wood Steel Steel, cast steel Steels over 700 N/mm (> 220 HB) Steels up to 1, 200 N/mm (< 38 HRC) Steels up to 700 N/mm (< 220 HB) Thermoplastics Thermosetting plastics Titanium Titanium alloys Tool steels White annealed cast iron (GTW, GJMW) Wood Zinc Applications Drilling Drive types Column drill Power drill Robot Stationary machines Tool machine

GBP 89.90
1

10x Pferd Twist Drill SPB DIN338 HSSE N 7.9 Inox

10x Pferd Twist Drill SPB DIN338 HSSE N 7.9 Inox

Spiral drill INOX dia. 7.9 mm HSS-E Co5 N DIN 338 135 for tough and hard materials Angle135 Diameter7.9 mm Flute length75 mm Length, total117 mm RPM from, grey cast iron, white cast iron403 RPM RPM from, hard non-ferrous metals1008 RPM RPM from, rust and acid-resistant steels403 RPM RPM from, soft non-ferrous metals1209 RPM RPM from, steels over 700 N/mm806 RPM RPM from, thermoplastics, fibre-reinforced plastics (GRP/CRP) 605 RPM RPM to, grey cast iron, white cast iron1008 RPM RPM to, hard non-ferrous metals2016 RPM RPM to, rust and acid-resistant steels806 RPM RPM to, soft non-ferrous metals2419 RPM RPM to, steels over 700 N/mm1008 RPM RPM to, thermoplastics, fibre-reinforced plastics (GRP/CRP) 1613 RPM Spiral angle, from36 VersionINOX Drilling tools with cross grinding for industrial uses. Fully ground, right-hand turning versions that produce precise drill holes thanks to their high concentricity and exact centring. PFERD offers spiral drills in the STEEL (118 point angle) and INOX (135 point angle) versions. High-performance drilling tools in the INOX in HSSE-Co5 (M35) version for industrial uses. Fully ground right-hand turning version with cross grinding that produces precise drill holes thanks to their high concentricity and exact centring. Advantages Very good chip removal. High concentricity. Exact centring and low feed force thanks to cross grinding. Particularly well suited for tough and hard materials, such as alloyed and high-strength steel, stainless steel (INOX) . Robust tip profile. Very long tool life. Very good temperature resistance due to Co content. Recommendations for use Observe the recommended rotational speeds. When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill tool life. Exception: when working on aluminium, use kerosene instead of cutting oil. When working on stainless steel (INOX) , remove any particles that break away from the workpiece in order to avoid corrosion. Clean the workpiece chemically or mechanically (etching/polishing, etc.) . Safety notes Wear eye protection! Follow the safety instructions! Materials that can be worked Aluminium Annealed cast iron Black annealed cast iron (GTS, GJMB) Brass Bronze Case-hardened steels Casting scale Casting scale with sand contamination and metal contamination Cast iron Cast steel Chipboard Cobalt-based alloys Copper Ductile cast iron Elastomers Fibre-reinforced thermosetting plastics (GRP, CRP) Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 % Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content 40 % Grey/nodular cast iron (GG/GJL, GGG/GJS) Hard aluminium alloys Hard non-ferrous metal Hardwood High-temperature-resistant materials Nickel-based alloys (e.g. Inconell and Hastelloy) Nickel or titanium-based superalloys Other Other non-ferrous metals Plastics Roller-bearing and ball-bearing steels Soft aluminium alloys Soft non-ferrous metal Soft titanium alloys (tensile strength 500 N/mm) Soft wood Stainless steel (INOX) Steel Steel, cast steel Steels over 700 N/mm (> 220 HB) Steels up to 1, 200 N/mm (< 38 HRC) Steels up to 700 N/mm (< 220 HB) Thermoplastics Thermosetting plastics Titanium Titanium alloys Tool steels Tough aluminium alloys White annealed cast iron (GTW, GJMW) Wood Zinc Applications Drilling Drive types Column drill Power drill Robot Stationary machines Tool machine

GBP 89.90
1