37 results (0,14205 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

System Sensor IM-10EA Ten Input Monitor Module

System Sensor IM-10EA Ten Input Monitor Module

System Sensor IM-10EA Ten Input Monitor ModuleThe IM-10EA Ten Input Monitor Module is intended for use in an intelligent alarm system. Each monitor module is intended to interface between a control panel and normally open contact devices such as pull stations. A common SLC input is used for all modules and the initiating device loops share a common supervisory supply and ground.Otherwise each monitor operates independently from the others. Each module also has panel-controlled tri-colour green red and amber LED indicators. The panel can cause the LEDs to blink latch on or latch off. The module also provides short circuit isolators to prevent shorts on the fire detection and alarm system loop from disabling more than one device on the intelligent loop.

GBP 538.40
1

System Sensor M210E-B Single Input Monitor Module With M200E-SMB

System Sensor M210E-B Single Input Monitor Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M210E-B Single Input Monitor Module With M200E-SMBProvides single channel monitoring of normally open contact fire alarm and supervisory devices. The M210E has a single tri-colour greenredyellow LED which can be set by panel command to pulse green each time the module is polled. In case of an alarm the panel can switch the red indicator on continuously.The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is overridden by a panel command to turn the red LED on.Key FeaturesComes withM200E-SMB for surface mounting

GBP 56.24
1

System Sensor Agile Wireless Gateway Device M200G-RF

System Sensor Agile Wireless Gateway Device M200G-RF

System Sensor Agile Wireless Gateway Device M200G-RF The System Sensor M200G-RF is a loop powered gateway unit from the Agile range of wireless fire system equipment. This device is designed to communicate with the System Sensor Agile range of wireless fire system devices.The Agile wireless platform is powered by robust mesh network technology providing up to two communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. Mesh network technology enables flexible and economic installations in a wide variety of building footprints.Please NoteThis panel is compatible with the Morley System Sensor DXc panel range only.

GBP 255.80
1

System Sensor Recess Mounting Kit White RMK400AP

System Sensor Recess Mounting Kit White RMK400AP

System Sensor Recess Mounting Kit White RMK400APRecess mounting kit suitable for flush mounting bases into a false ceiling. The System Sensor RMK400AP recessed mounting kit provides a simple installation solution where the application demands a lower profile sensor. The RMK400AP is for white sensors the RMK400AP-IV is for Ivory coloured sensors.Key FeaturesReduces the depth of any System Sensors sensor mounted in a standard 102mm diameter base by up to 20mm.Appropriate for drywall or suspended acoustical panel ceilings.May be used with standard junction boxes connected to flexible conduit.Incorporates special mounting bracket that secures the kit and base assembly to the junction box and ceiling panel.

GBP 19.82
1

System Sensor BSO-PP-N00 Base Sounder

System Sensor BSO-PP-N00 Base Sounder

System Sensor BSO-PP-N00 Base SounderBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 48.12
1

System Sensor BSO-PP-I00 Base Sounder with Loop Isolation

System Sensor BSO-PP-I00 Base Sounder with Loop Isolation

System Sensor BSO-PP-I00 Base Sounder with Loop IsolationBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 58.90
1

System Sensor M200G-RF-26 Agile Gateway

System Sensor M200G-RF-26 Agile Gateway

System Sensor M200G-RF-26 Agile GatewayLoop-powered Gateway device for System Sensor Agile wireless system. Up to 8 Gateways may be used on the same loop. This requires a B501AP base. Compatible with DXc panels only.The System Sensor M200G-RF is a loop powered gateway unit from the Agile range of wireless fire system equipment. This device is designed to communicate with the System Sensor Agile range of wireless fire system devices.The Agile wireless platform is powered by robust mesh network technology providing up to two communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. Mesh network technology enables flexible and economic installations in a wide variety of building footprints.Key FeaturesRequires a B501AP basePlease NoteThis panel is compatible with the Morley System Sensor DXc panel range only.

GBP 289.18
1

System Sensor BSO-PP-N00-B Base Sounder With Base

System Sensor BSO-PP-N00-B Base Sounder With Base

Please note The price of this product including the base is a special promotional offer directly from the manufacturer.System Sensor BSO-PP-N00-B Base Sounder With BaseBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 35.16
1

System Sensor M201E-B Output Control Module With M200E-SMB

System Sensor M201E-B Output Control Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M201E-B Output Control Module With M200E-SMBThe M201E provides a single output that can be switched when commanded by a fire alarm control panel. In the supervised mode the M201E supervises the wiring to the load devices. Upon command from the fire alarm control panel the M201E switches an external power supply to operate these devices while de-activating the load supervision.The module raises an unlatched fault condition if the external power supply voltage falls below the fixed threshold. In the unsupervised mode the M201E provides one set of form C changeover contacts and does not provide load nor power supply supervision. The M201E has built-in short circuit protection for the communications loop which may be selecteddeselected to meet the specific requirements of each installation.Key FeaturesComes withM200E-SMBfor surface mounting

GBP 58.97
1

System Sensor BSO-PP-I00-B Base Sounder with Loop Isolation With Base

System Sensor BSO-PP-I00-B Base Sounder with Loop Isolation With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor BSO-PP-I00-B Base Sounder with Loop Isolation With BaseBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501AP - includedDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 49.67
1

System Sensor Agile Wireless Photo-Thermal-IR Detector 22051TLE-RF-26

System Sensor Agile Wireless Photo-Thermal-IR Detector 22051TLE-RF-26

System Sensor Agile Wireless Photo-Thermal-IR Detector 22051TLE-RF-26The 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting. Agile wireless optical thermal and IR detector for use with the System Sensor Agile wireless system.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibility

GBP 232.72
1

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector

System Sensor 22051TLE-26 Photoelectric Thermal Infrared DetectorThe 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 77.11
1

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector with Isolator

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector with Isolator

System Sensor 22051TLE-26 Photoelectric Thermal Infrared Detector with IsolatorThe 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 92.95
1

System Sensor WSS-PR-I00 Wall Mounted Sounder Strobe With Isolator - White Skirt

System Sensor WSS-PR-I00 Wall Mounted Sounder Strobe With Isolator - White Skirt

System Sensor WSS-PR-I00 Wall Mounted Sounder Strobe With Isolator - White SkirtThe WSS-PR-I00 is a wall mounted sounder strobe with integral isolator.The beacon has fast and simple installation and is control powered by the fire panel via the loop wiring. The control of the device is enabled using on-board switches or via the digital protocol using the control panel.Key FeaturesWall Mounted Addressable Sounder StrobeColour White Body Red LensIntegral IsolatorFast and simple installationPlease note This product is not approved to EN54-23 Visual Alarm Device and must not be used as a visual alarm device to provide a primary warning notification of fire.

GBP 86.93
1

System Sensor 52051RE-26 Rate of Rise 58C Heat Detector

System Sensor 52051RE-26 Rate of Rise 58C Heat Detector

System Sensor 52051RE-26 Rate of Rise 58C Heat DetectorThe 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 53.02
1

System Sensor WSO-PP-I00 Wall Mounted White Sounder with Loop Isolation

System Sensor WSO-PP-I00 Wall Mounted White Sounder with Loop Isolation

System Sensor WSO-PP-I00 Wall Mounted White Sounder with Loop IsolationWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 61.27
1

System Sensor WSS-PC-N00 Wall Mounted Sounder VAD Clear Lens with Red Flash

System Sensor WSS-PC-N00 Wall Mounted Sounder VAD Clear Lens with Red Flash

System Sensor WSS-PC-N00 Wall Mounted Sounder VAD Clear Lens with Red FlashIt utilises the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder and intense strobe give a visible and audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounder and strobeCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panelPositive poke yoke engagementAddress tag for clear indicationAnti-tamper featureSimple familiar rotary wheel address controls

GBP 78.01
1

System Sensor WSO-PR-N00 Wall Mounted Red Sounder

System Sensor WSO-PR-N00 Wall Mounted Red Sounder

System Sensor WSO-PR-N00 Wall Mounted Red SounderWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 47.51
1

System Sensor WST-PC-N00 Wall Mounted VAD Clear Lens with Red Flash

System Sensor WST-PC-N00 Wall Mounted VAD Clear Lens with Red Flash

System Sensor WST-PC-N00 Wall Mounted VAD Clear Lens with Red FlashWall mount strobe is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its intense strobe gives a highly visible warning. A choice of lens colours makes the device suitable for a wide variety of applicationsKey FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of strobePositive poke yoke engagementAddress tag for clear indicationAnti-tamper featureSimple familiar rotary wheel address controlsCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols

GBP 38.52
1

System Sensor WSO-PR-I00 Wall Mounted Red Sounder with Loop Isolation

System Sensor WSO-PR-I00 Wall Mounted Red Sounder with Loop Isolation

System Sensor WSO-PR-I00 Wall Mounted Red Sounder with Loop IsolationWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 55.08
1

System Sensor WSO-PP-N00 Wall Mounted White Sounder

System Sensor WSO-PP-N00 Wall Mounted White Sounder

System Sensor WSO-PP-N00 Wall Mounted White SounderWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 50.95
1

System Sensor 52051EI-26 Fixed 58C Heat Detector with Isolator

System Sensor 52051EI-26 Fixed 58C Heat Detector with Isolator

System Sensor 52051EI-26 Fixed 58C Heat Detector with IsolatorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 60.59
1

System Sensor 52051E-26 Fixed 58C Heat Detector

System Sensor 52051E-26 Fixed 58C Heat Detector

System Sensor 52051E-26 Fixed 58C Heat DetectorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 45.38
1

System Sensor 52051HTE-26 High Temperature Fixed 78C Heat Detector

System Sensor 52051HTE-26 High Temperature Fixed 78C Heat Detector

System Sensor 52051HTE-26 High Temperature Fixed 78C Heat DetectorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 53.02
1

System Sensor M220EA Dual Input or Monitor Module

System Sensor M220EA Dual Input or Monitor Module

System Sensor M220EA Dual Input or Monitor ModuleThe wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The M220EA monitors one or two sets of normally open contacts and has two tri-colour LED indicators One for each channel. The fire panel can be configured to switch the relevant channel indicator on red in the event of an alarm on an input channel. The indicators can be set by panel command to pulse green each time the module channel is polled. The relevant indicator blinks yellow if the module detects an open-circuit on the input circuit.This module features automatic fault supervision and a built-in isolator on the analogue addressable circuit. The isolator may be bypassed.Two mounting holes and a pair of DIN rail clips allow the module to be installed in any type of enclosure including a purpose-built surface-mount box M200E-SMB. The indicator LEDs and address switches are accessible and visible in both DIN-rail and surface mount installations.Key FeaturesIndividually addressable by the fire panelInput circuits supervised for open-circuit faultsTri-colour indicator LEDs visible from front and one sideAutomatic detection of short-circuits on AA circuitAA circuit short-circuit isolatorOptional isolator bypassScrewdriver operated rotary address switches accessible from front and one sideClips for top hat 35 mm DIN railTwo mounting holesUp to 99 module addresses per AA circuit F220 F100AUses two addresses on the analogue addressable circuitPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 86.75
1