ProfitSpring | B2B PPC Agency

Vesda Xtralis LT-ACC-HUB-PWR-HON Hub Direct Power LT Gen 3

Vesda Xtralis LT-ACC-HUB-PWR-HON Hub Direct Power LT Gen 3The Hub originates the daisy-chain connection of the sensors and distributes 12 VDC to the sensors Hub - PoE receives power from PoE Hub - Direct Power receives power from a 12 VDC Power Supply. Hubs communicate with the sensors over CANbus and relay information to the Controller via TCPIP over Ethernet.Hubs detect various errors and alarm conditions for self-diagnosing capabilities.Hub - PoE has two RJ45 connectors for the daisy-chain connections to sensors. Hub - Direct Power has one RJ45 connector for the daisy-chain connections to sensors.

GBP 216.30

1

Vesda Xtralis PIP-006 45 Elbow Bend Pack of 10

Vesda Xtralis PIP-006 45 Elbow Bend Pack of 10These 45 elbows are used to divert pipework around obstructions. The 45 bend allows for less air loss over the 90 elbow. They should always be connected withABS solvent cement.Key FeaturesMaterial ABSColour RedOperating temperature range -40C to 70CEN54 testedPlease Note The PIP-006 is equivalent to the RED45.

GBP 6.58

1

Vesda Xtralis White 45 Elbow - Pack of 10 PIP-006-W

Vesda Xtralis White 45 Elbow - Pack of 10 PIP-006-WThese 45 elbows are used to divert pipework around obstructions. The 45 bend allows for less air loss over the 90 elbow. They should always be connected withABS solvent cement.Key Features Tech SpecsMaterial ABSColour WhiteOperating temperature range -40C to 70CPlease Note The PIP-006-W is equivalent to the WHT45.

GBP 6.58

1

Vesda Xtralis 25mm 2-Way Ball Valve

Vesda Xtralis 25mm 2-Way Ball Valve25mm 2 Way Ball Valve. Vesda have over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Please note The PIP-023 is equivalent to the RED22P025I.

GBP 46.04

1

Vesda Xtralis VLI-885 LaserINDUSTRIAL Detector with Relays VESDAnet and Ethernet

Vesda Xtralis VLI-885 LaserINDUSTRIAL Detector with Relays VESDAnet and EthernetThe VESDA VLI by Xtralis is an industry first early warning aspirating smoke detection ASD system designed to protect industrial applications and harsh environments of up to 2000m2 20000 sq. ft..The VLI detector combines a fail-safe Intelligent Filter patent pending with an advanced clean-air barrier for optics protection allowing the use of absolute detection and a long detection chamber life without the need for recalibration.The Intelligent Filtereffectively reduces the level of pollution in the air sample before it enters the detection chamber which dramatically extends the operational life of the detector in harsh and polluted environments.is fully monitored therefore providing consistent sensitivity over the entire operational life of the detector.The VLI detector features a robust IP54-rated enclosure which provides protection against dust ingress and water splash. In the majority of applications this eliminates the need to use expensive external IP enclosures thus simplifying and reducing the cost of installation. The VLI detector is equipped with a powerful aspirator that provides a total pipe length of 360m 1200 ft. It is fully supported by the Xtralis ASPIRE2 VSC and VSM4 software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.The AutoLearn commissioning assistant reduces setup time and ensures optimum alarm and flow thresholds in a range of environments. The VLI detector features a standardised industry BACnet over Ethernet communication protocol for remote monitoring and programming and connection to building management systems BMS and automation devices. This translates to direct cost savings on integration and monitoring. The VLI detector is inherently less prone to nuisance alarms due to the intelligent filter lint trap sub-sampling probe and secondary filter. Coupled with its modular design VLI offers a lower total cost of ownership over the life of the product.Key FeaturesSuitable for Class 1 Division 2 applications - Groups ABC DUp to 2000m2 20000 sq. ft. coverageUp to 4 inlet pipesTotal pipe length up to 360m 1200 ftFive 5 high intensity status LEDs for greater visibilityRobust absolute smoke detectionIntelligent Filter patent pendingLint Trap to capture fibrous particulatesSub-sampling Probe inertial separatorSecondary FilterClean air barrier for optics protectionReferencingAutoLearn Smoke and FlowClean Air ZeroAir-path monitoringFive 5 relays Fire Fault and 3 configurableRelays configurable as latching or nonlatchingExpandable GPI and relaysUltrasonic flow sensingXtralis VSC Xtralis VSM4 and ASPIRE2 software supportIP54 EnclosureEasy mounting through steel support bracketModular field replaceable parts for ease of servicingBACnet over EthernetLocal USB configuration portEasy cable termination accessImperial and metric pipe portsRubberized finish to external housing

GBP 6726.62

1

Vesda Xtralis VLI-880 LaserINDUSTRIAL Detector with Relays amp Ethernet Only

Vesda Xtralis VLI-880 LaserINDUSTRIAL Detector with Relays Ethernet OnlyThe VESDA VLI by Xtralis is an industry first early warning aspirating smoke detection ASD system designed to protect heavy industrial applications with dirty or harsh environments of up to 2000m2 20000 sq. ft..Until now ASD has not been recommended in challenging dirty environments however the new Vesda VLI removes any previous boundaries enabling the facility of very early smoke detection in almost any conditions.The VLI detector combines a fail-safe Intelligent Filter patent pending with an advanced clean-air barrier for optics protection allowing the use of absolute detection and a long detection chamber life without the need for recalibration.The Intelligent Filtereffectively reduces the level of pollution in the air sample before it enters the detection chamber which dramatically extends the operational life of the detector in harsh and polluted environments.is fully monitored therefore providing consistent sensitivity over the entire operational life of the detector.The VLI detector features a robust IP54-rated enclosure which provides protection against dust ingress and water splash. In the majority of applications this eliminates the need to use expensive external IP enclosures thus simplifying and reducing the cost of installation. The VLI detector is equipped with a powerful aspirator that provides a total pipe length of 360m 1200 ft. It is fully supported by the Xtralis ASPIRE2 VSC and VSM4 software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.The AutoLearn commissioning assistant reduces setup time and ensures optimum alarm and flow thresholds in a range of environments. The VLI detector features a standardised industry BACnet over Ethernet communication protocol for remote monitoring and programming and connection to building management systems BMS and automation devices. This translates to direct cost savings on integration and monitoring. The VLI detector is inherently less prone to nuisance alarms due to the intelligent filter lint trap sub-sampling probe and secondary filter. Coupled with its modular design VLI offers a lower total cost of ownership over the life of the product.Key FeaturesSuitable for Class 1 Division 2 applications - Groups ABC DUp to 2000m2 20000 sq. ft. coverageUp to 4 inlet pipesTotal pipe length up to 360m 1200 ftFive 5 high intensity status LEDs for greater visibilityRobust absolute smoke detectionIntelligent Filter patent pendingLint Trap to capture fibrous particulatesSub-sampling Probe inertial separatorSecondary FilterClean air barrier for optics protectionReferencingAutoLearn Smoke and FlowClean Air ZeroAir-path monitoringFive 5 relays Fire Fault and 3 configurableRelays configurable as latching or nonlatchingExpandable GPI and relaysUltrasonic flow sensingXtralis VSC Xtralis VSM4 and ASPIRE2 software supportIP54 EnclosureEasy mounting through steel support bracketModular field replaceable parts for ease of servicingBACnet over EthernetLocal USB configuration portEasy cable termination accessImperial and metric pipe portsRubberized finish to external housing

GBP 6190.67

1

Vesda Xtralis Discreet Clear End Cap for 10mm OD Tube Pack of 10

Vesda Xtralis Discreet Clear End Cap for 10mm OD Tube Pack of 10Vesda Xtralis Capillary 10mm Discreet Endcap - with over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Please note The 222-059 is equivalent to the REDCAP010N.

GBP 5.22

1

Vesda Xtralis 059-007 Conical Sampling Point Kit

Vesda Xtralis 059-007 Conical Sampling Point KitThe Vesda25mm Capillary Sampling Point -Conical 059-007set has a tempered sampling tip installed at its end. The set includes capillary tube adapter capillary tube 2m long and 10mm in diameter and a flat sampling tip.Kit Includes2m of 10mm OD tubeTrunk AdaptorPoint and decalWith over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Please note The 059-007 is equivalent to the redCSK.

GBP 17.23

1

Xtralis OSID OSID-INST Installation Kit

Xtralis OSIDOSID-INSTInstallation KitThe OSID Installation Kit OSID-INST is used in commissioning and maintaining the correct operation of the OSID Smoke Detector.When the OSID system is installed over very large distances and in brightly lit areas it may be difficult to see the output laser from the OSID Laser Alignment Tool when commissioning the system. To aid in the alignment of the Imager and Emitter the Commissioning Aid reflector is provided. The reflector should be attached to the opposing unit that is not being aligned. For example if the Emitter is being aligned the reflector should be attached to the front cover of the Imager. Returning light to the user off the reflector from the laser alignment tool will be brighter and make it easier to determine if the unit being commissioned has been aligned correctly.For to see how to use the Intallation Kit please view the OSID Product Guide pages 35 - 38.The kit includesOSID Installation and Maintenance ManualOSID commissioning aid reflectorBlu-Tack adhesiveOSID smoke simulating test filterOSID cleaning clothOSID serial PC interface cableOSID laser alignment tool with three LR44 button cell batteries pre-installed

GBP 193.92

1

Vesda PIP-038 ASD Quick Release Kit Air Line ABS 34quot

Vesda PIP-038 ASD Quick Release Kit Air Line ABS 34When the aspirating smoke detection system is installed in a dirty or dusty environment the sampling pipes and sampling holes can get obscured over a period of time by the various airborne particles. As a result it is recommend to clean the sampling pipes and holes by blowing low pressure compressed air in the reverse direction through the sampling pipes. The connection of the compressed air to the sampling pipe and the release of excess air at the end of the sampling pipe can be cumbersome.With introduction of the Quick Release Airline Valve 9-30976 the Large Check Valve 9-10978 and Large 2 Way Ball Valve 9-10980 this does not need to be the case anymore. The quick release airline valve is installed close to the detector. During maintenance the detector can be switched-off and the valve closed to prevent any damage to the detector during the clearing process. The low pressure compressed air can now be easily connected to the quick release.At the far end of the sampling pipe the large check valve or large 2 way ball valve can be used. The check value is the easiest to use as it will automatically open to release excess pressure during the cleaning process and does not require any human interaction. In some cases the check valve might not be suitable and then the 2 way ball valve can be used to manually open the far end of the sampling pipe.Key FeaturesEasy connection of airlineRobust ball valve to protect ASDFor use with 9-10978 - check valve

GBP 105.47

1

Vesda Xtralis VSW-216 VSM4 Additional PC Licence

Vesda Xtralis VSW-216 VSM4 Additional PC LicenceAn additional PC Licence for the VSM4.VSM4 configures monitors and trouble-shoots Xtralis aspirating smoke detection systems. It is easy to use and has been designed to provide the operator with complete control. The user friendly interface allows you to assess and respond quickly to system events all from one convenient location. VSM4 is a total solution for integrated control and monitoring of your Xtralis very early warning smoke detection systems.Key FeaturesFull VESDA and VESDA-E system controlComprehensive event managementDrill down floor plansEvent response notification by email and SMS2 to defined users on defined eventsMaintenance information and system optimizationComprehensive configuration and commissioning of all Xtralis devicesFully integrated floor plan design tools compatible with most drawing formatsRemote management over multiple network typesReal-time graphical event indicatorsPowerful event log filteringEvent log archiving for future interrogationExtensive reporting capabilitiesMultiple monitor supportMulti-language supportCustomizable software viewsIndividual user accounts integrated with system access rolesSupports text-to-speech in multiple languages

GBP 1267.87

1

Vesda Xtralis VSW-206 VSM4 Primary PC Licence

Vesda Xtralis VSW-206 VSM4 Primary PC LicenceAPrimary PC Licence for the VSM4.VSM4 configures monitors and trouble-shoots Xtralis aspirating smoke detection systems. It is easy to use and has been designed to provide the operator with complete control. The user friendly interface allows you to assess and respond quickly to system events all from one convenient location. VSM4 is a total solution for integrated control and monitoring of your Xtralis very early warning smoke detection systems.Key FeaturesFull VESDA and VESDA-E system controlComprehensive event managementDrill down floor plansEvent response notification by email and SMS2 to defined users on defined eventsMaintenance information and system optimizationComprehensive configuration and commissioning of all Xtralis devicesFully integrated floor plan design tools compatible with most drawing formatsRemote management over multiple network typesReal-time graphical event indicatorsPowerful event log filteringEvent log archiving for future interrogationExtensive reporting capabilitiesMultiple monitor supportMulti-language supportCustomizable software viewsIndividual user accounts integrated with system access rolesSupports text-to-speech in multiple languages

GBP 1497.07

1

Vesda Xtralis 25mm Flexible 1m Long Bend

Vesda Xtralis 25mm Flexible 1m Long BendWith over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Always use tools specifically designed forplastic pipe.Protective gloves are recommended for usewhen solvent cementing. If hands come into contact with cement use a waterless abrasive soap.Avoid sources of heat or open flames when solvent cementing. Do not smoke.Always chamfer and deburr pipe ends.Use the proper solvent cement note air shipments of solvent cement are forbidden by law.Always replace lids on cans when not in use.Never dilute solvent cement.Keep jointing surfaces dry in wet weather.Avoid direct inhalation of fumes. Use in a well-ventilated area.Wipe up spills or leaks immediately with clean lint free cloth or paper towels.Follow recommended cure times prior to testing the system.Prevent excessive solvent cement from running into the pipe or fitting socket.The Integrity of air sampling systems may be affected if proper CPVC solvent cement is not used. The Safety Crewdisclaims responsibility for any air sampling pipe system constructed with cements other than those recommended.Please note The PIP-021 is equivalent to the REDFLXI25B.

GBP 24.38

1

Vesda Xtralis REDFLEXI25B 25mm Flexible 1m Long Bend

Vesda Xtralis REDFLEXI25B 25mm Flexible 1m Long BendWith over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Always use tools specifically designed forplastic pipe.Protective gloves are recommended for usewhen solvent cementing. If hands come into contact with cement use a waterless abrasive soap.Avoid sources of heat or open flames when solvent cementing. Do not smoke.Always chamfer and deburr pipe ends.Use the proper solvent cement note air shipments of solvent cement are forbidden by law.Always replace lids on cans when not in use.Never dilute solvent cement.Keep jointing surfaces dry in wet weather.Avoid direct inhalation of fumes. Use in a well-ventilated area.Wipe up spills or leaks immediately with clean lint free cloth or paper towels.Follow recommended cure times prior to testing the system.Prevent excessive solvent cement from running into the pipe or fitting socket.The Integrity of air sampling systems may be affected if proper CPVC solvent cement is not used. The Safety Crewdisclaims responsibility for any air sampling pipe system constructed with cements other than those recommended.Please note The PIP-021 is equivalent to the REDFLXI25B.

GBP 24.38

1

Vesda Xtralis PIP-015 Flush Sample Point Head Only for 10mm OD Tube

Vesda Xtralis PIP-015 Flush Sample Point Head Only for 10mm OD TubeDue to the aesthetic design of some buildings such as ornate ceilings or ceiling art-work a discreet unobtrusive smoke detection system is often desirable. Large open atria or voids feature stratified thermal layers that can prevent cooled smoke from reaching ceiling level. As such conventional systems will normally only respond when a fully-fledged fire condition is reached by which time significant damage has already occurred.VESDA provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location. The room fabric often dictates the location of these capillary tubes. Hiding the capillary tubes behind light fittings blending in with ceiling paintings or forming part of the ceiling sculptures can all be used to provide invisible smoke detection. In high volume atria applications such as cathedrals capillary sample points can be routed into the area at intermediate vertical levels to good effect to overcome stratification. The higher potential sensitivity of the VESDA system means that less smoke is required at the sample points to provide an alarm condition.With over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Key FeaturesFor use with Red or White ABSOperating temperature range -40C to 70CLPCB approvedEN54 testedApplications Used inChurchesHospitalsMuseums GalleriesPrisonsLibrariesArchivesConcert HallsPlease Note The PIP-015 is equivalent to the REDASP025F.

GBP 9.07

1

Vesda-E VEA VSP-990-330 6mm Microbore Tube UL-compliant Plenum-rated 330ft

Vesda-E VEA VSP-990-330 6mm Microbore Tube UL-compliant Plenum-rated 330ftVESDA-E VEA microbore tubes are custom made high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance. They are lightweight and flexible for easy handling and installation and marked with a white ink numbering system over the full length of the tubing. The numbering system includes individual unique identification of each tube and distance marking at regular intervals making them very efficient to install and keep clean installationrecords.These tubes come in black colour with red stripes for use in smoke detection and meet requirements of global installation codes. These tubes have no active components and they eliminate the need for any electrical wiring for smoke detection resulting in fast and easy installation without the need to follow electrical codes.It is important to use VESDA-E VEA microbore tubes with the VESDA-E VEA detectors to maintain their smoke detection performance. These tubes come in two different diameters 6mm and 4mm.VEA micrbore tube fittings comprise of straight unions and other types of joiners and 6mm to 4mm adaptors for easy installations blanking plugs are used to block the unused ports on VEA.Key FeaturesPlenum ratedFlame retardantHigh quality polyethylene materialStress crack resistantUnique IDDistance marking at regular intervalsMeets requirements of global installation codesListings ApprovalsUL 1820NFPA 90AEN 54-202006 clause 5.7BS EN 61386-12007 clauses 10.2 10.3 and 12.2

GBP 156.30

1

Vesda-E VEA VSP-991 4mm Microbore Tube 50m

Vesda-E VEA VSP-991 4mm Microbore Tube 50mVESDA-E VEA microbore tubes are custom made high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance. They are lightweight and flexible for easy handling and installation and marked with a white ink numbering system over the full length of the tubing.The numbering system includes individual unique identification of each tube and distance marking at regular intervals making them very efficient to install and keep clean installation records. These tubes come in black colour with red stripes for use in smoke detection and meet requirements of global installation codes.These tubes have no active components and they eliminate the need for any electrical wiring for smoke detection resulting in fast and easy installation without the need to follow electrical codes.It is important to use VESDA-E VEA microbore tubes with the VESDA-E VEA detectors to maintain their smoke detection performance.These tubes come in two different diameters 6mm and 4mm. For more information on tube usage refer to VESDA-E VEA Product Guides documents 27034 and 27035 and VEA Microbore Tube Length Calculator document 29262.VEA microbe tube fittings comprise of straight unions and other types of joiners and 6mm to 4mm adaptors for easy installations blanking plugs are used to block the unused ports on VEA.Key FeaturesPlenum ratedFlame retardantHigh quality polyethylene materialStress crack resistantUnique IDDistance marking at regular intervalsMeets requirements of global installation codes

GBP 267.11

1

Vesda-E VEA VSP-998 6mm Blanking Plug Pack of 50

Vesda-E VEA VSP-988 6mm Blanking Plug Pack of 50VEA microbore tube fittings comprise of straight unions and other types of joiners and 6mm to 4mm adaptors for easy installations blanking plugs are used to block the unused ports on VEA.VESDA-E VEA microbore tubes are custom made high quality plenum rated flame retardant polyethylene tubes.They have superior stress crack resistance for reliable long-term performance. They are lightweight and flexible for easy handling and installation and marked with a white ink numbering system over the full length of the tubing.The numbering system includes individual unique identification of each tube and distance marking at regular intervals making them very efficient to install and keep clean installation records. These tubes come in black colour with red stripes for use in smoke detection and meet requirements of global installation codes.These tubes have no active components and they eliminate the need for any electrical wiring for smoke detection resulting in fast and easy installation without the need to follow electrical codes.It is important to use VESDA-E VEA microbore tubes with the VESDA-E VEA detectors to maintain their smoke detection performance.These tubes come in two different diameters 6mm and 4mm. For more information on tube usage refer to VESDA-E VEA Product Guides documents 27034 and 27035 and VEA Microbore Tube Length Calculator document 29262.VEA microbore tube fittings comprise of straight unions and other types of joiners and 6mm to 4mm adaptors for easy installations blanking plugs are used to block the unused ports on VEA.

GBP 72.31

1

Vesda Xtralis VKT-855 VESDA-E VES Demonstration Kit

Vesda Xtralis VKT-855 VESDA-E VES Demonstration KitThe VESDA-E VES is similar to the flagship VESDA-E VEP aspirating smoke detector but also includes a valve mechanism in the inlet manifold and software to control the airflow from the four Sectors pipes. This configuration enables a single zone to be divided into four separate sectors for example distinguishing between separate aisles within a data room.The VES enables the user to locate the source of smoke by identifying the first sector to reach the Alert level. The detector then continues to sample from all sectors to monitor fire growth and will report separate alarm levels for each sector.The VES provides four individually configurable alarm levels Alert Action Fire 1 and Fire 2 for each sector allowing optimum protection in a wide range of applications. Built on the Flair detection technology and years of application experience VES detectors achieve consistent performance over their lifetime via absolute calibration. In addition the VES delivers a range of revolutionary features that provide user value.How it WorksThe VES draws air from all sectors in use. If the smoke level reaches the Adaptive Scan Threshold the VES quickly scans each sector to identify which sector is carrying smoke. The first sector to reach the Alert level is designated as the First Alarm Sector FAS and this sector is signalled to the user. If two or more sectors reach the Alert level then the sector with the highest smoke concentration is designated as the First Alarm Sector FAS. Once Fast Scan is completed and the FAS identified the VES continues to closely monitor all four sectors to track fire growth and maintain full protection of the area.Key FeaturesSector addressability for up to four sectorsAdaptive scan thresholdFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour configurable alarm levels per sector and a wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningBackward compatible with VLS and VESDAnetEthernet for connectivity with Xtralis software for configuration secondary monitoring and maintenanceSecondary monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies enable faster service and maximum uptime

GBP 6136.43

1

Vesda OSI-RE-SS OSID R Reflective Beam

Vesda OSI-RE-SS OSID R Reflective BeamThe Vesda OSI-RE-SS is a 4-wire single-ended reflected type beam smoke detector that includes an 8 reflector and an integral sensitivity test.The Vesda OSI-RE-SS is a reflector-type linear optical beam smoke detector designed to operate as a component of fire alarm systems. The beam operates primarily on the principle of light obscuration utilising an Infra-Red beam. Optical beam smoke detectors are particularly appropriate for protecting buildings with large open spaces such as warehouses atriums etc.The OSI-RE-SS detector is a combined transmitterreceiver unit that can be directly connected to a conventional detector circuit.Key FeaturesCombined transmitter and receiver unit range 5-100 m 16-328 ftConventional modelReceiver consists of a CMOS imaging CCDWide 12 field of viewIntuitive beam alignment indicated by directional arrowsSingle IR wavelengthHighly resistant to building movement tolerates - 1 movementResistant to strong light sources does not alarm when saturated by sunResistant to large solid intruding objectsAutomatic sensitivity threshold level setting50 horizontal and 20 vertical beam alignmentBuilt-in heaterElectronic simulated smoke test from ground levelStandby fault and alarm LED indicators visible from the front and bottomAutomatic drift compensationPaintable coverRemovable plug-in terminal blocksOptional heater kit available for the reflectorThe Infra-Red transmitter and receiver Imager generates a beam of light towards a high efficiency reflector. The reflector returns the beam to the receiver where an analysis of the received signal is made. The change in the strength of the received signal is used to determine the alarm condition.The receiver imager has a wide FOV of 12 and tracks automatically the reflector in case of building movement or movement of its support structure. It is virtually impossible for the receiver to lose the reflector out of its side of view without any structural damage being caused to the building. As a result of this operation the OSI-RE-SS eliminates the number one cause of false alarms andor faults with traditional beam detectors.Optical filtering high-speed image acquisition and intelligent software algorithms provide the OSID-RE system with higher levels of stability and with greater resistance to high level lighting variability. As such the detector has a better resistance to sunlight and intruding objects in its FOV.The detector will not alarm when saturated by sunlight reflected sunlight or any other very bright light sources. In worst case the detector will go in to trouble and hence solving another cause of false alarms with traditional basic photocell receiver beam detectors. Thanks to the smoke imaging techniques the detector will not alarm for partial and sudden blockage.The alignment of the detector is extremely intuitive fast and accurate. Both the IR transmitter and the CMOS imager are contained in the eyeball that can turn freely in all directions. The eyeball moves - 20 in the vertical direction and 50 in the horizontal direction. Four arrows that indicate the direction to move the eyeball will guide the user to find the imagers perfect alignment with the reflector.To get started swiftly at long distances a laser tool can be inserted in the eyeball to allow finding the reflector quickly and then fine-tuning the eyeball to the optimum alignment. Once the optimum alignment is finalised signalled by all green arrows and LED the eyeball is locked by tightening the lever on its side. A paintable cover is then placed over the front to hide the alignment arrows locking mechanism and secures the locking lever in locked position. Unique in the market the sensitivity of the detector is selected and set automatically at the optimum sensitivity based on the size of the reflector measured in the FOV. The detector incorporates automatic drift compensation whereby the detector will adjust its detection thresholds in line with any long term signal reduction of the beam caused by contamination of the optical surfaces. An internal heating option is also provided on the Imager to prevent condensation on the optical surface.

GBP 870.91

1

Vesda-E VEP amp VES VSP-962-20 Spare Replacement Filter Pack of 20

Vesda-E VEP VES VSP-962-20 Spare Replacement Filter Pack of 20The VESDA detector uses a two-stage filter to protect the optics of the detection head. The filter is made in a compact construction and is intended for single use. The filter removes dust and other dirt from the sucked air creating a protective barrier for the optics.The detector monitors the filter filling. The filter should be replaced at least every 2 years or if the filter has previously been filled in accordance with the message. In environments with significant air pollution it may be necessary to replace the filter more frequently which should be determined individually based on information from the detector.A properly configured system will remind the user to change the filter reporting on zone detectors filter damage on all detectors connected to the given detector. Damage is reported ifthe dust meter will exceed the programmed limitthe system clock will indicate the date on which the filter replacement occursThe replacement period is calculated based on the date of the last filter replacement and data in the detector configuration

GBP 1497.66

1

Vesda-E VEP amp VES VSP-962 Spare Replacement Filter Singular

Vesda-E VEP VES VSP-962 Spare Replacement Filter SingularThe VESDA-E detector uses a two-stage filter to protect the optics of the detection head. The filter is made in a compact construction and is intended for single use. The filter removes dust and other dirt from the sucked air creating a protective barrier for the optics.The detector monitors the filter filling. The filter should be replaced at least every 2 years or if the filter has previously been filled in accordance with the message. In environments with significant air pollution it may be necessary to replace the filter more frequently which should be determined individually based on information from the detector.A properly configured system will remind the user to change the filter reporting on zone detectors filter damage on all detectors connected to the given detector. Damage is reported ifThe dust meter will exceed the programmed limitThe system clock will indicate the date on which the filter replacement occursThe replacement period is calculated based on the date of the last filter replacement and data in the detector configuration

GBP 92.72

1

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda XtralisPIP-027Air Sampling Test Point with CapThey are designed to measure the transportation time a small quantity of smoke is introduced at the furthest point and the measurement in time is calculated from when the smoke enters the sampling point to when the ASD reacts. The maximum transport time is 120 seconds 2 minutes. Test points are the ideal solution for flexibility and convenience. They are installed at the end of the pipe run however for areas such as a lift shaft where accessibility is limited the pipe run can be brought into a riser.A key element of the VESDA system is its suction system which actively transports air from the protected area to the detector.The test point is for periodic smoke testing of the VESDA system for hard to reach areas.VESDA installations can be designed for the most complex areas using carefully selected shaped elements.The use of these shaped elements has a positive effect on the pneumatic system of the installation which translates into the unique and legendary quality of the VESDA system work in each pneumatic system.The suction installation is calculated with theASPIREprogramme.The program is used for modelling and visualization of aspiration installations class calculation in accordance with PN-EN-54-20.Please note The PIP-027 is equivalent to the REDAST025C.

GBP 7.49

1

Vesda Xtralis KA-1 Steam Trap

Vesda Xtralis KA-1 Steam TrapIf the Compact ASD is operated in environments where condensate can form in the pipe system then a condensate trap is used. To collect the condensate the steam trap is fitted at the lowest point of the pipe system between the air filter and the smoke detection system. Using 45 angles gives optimum wall distance.The steam trap can be operated in a temperature range of 0C to 50C. The sinter filter in the condensate trap has a pore width of 50 m and additionally absorbs coarse dust particles.The condensate trap is used in the following areasAreas with severely oscillating temperatures and high air humidityExternal areasSauna areas

GBP 280.10

1

Vesda Xtralis M6 Rawlplug Adaptor - Pack of 100 PIP-032

Vesda Xtralis M6 Rawlplug Adaptor - Pack of 100 PIP-032The M6 rawlplug adaptor is used for fixing the clip to a wall.A key element of the VESDA suction system is the suction pipe system that actively transports air from the protected area to the detector.The VESDA system installation can be designed for the most complex areas using a small number of shaped elements that have been carefully selected.The use of these elements has a positive effect on the installations automation which translates into the quality of VESDA systems.Please Note The PIP-032 is equivalent to the ACCRPA025A.

GBP 59.53

1

Brand

Merchant

Price (EUR)