102 results (0,13435 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10Air sampling test points allow for functional smoke testing of aspirating smoke detection systems and are typically located at the end of a sampling pipe network.VESDA provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location. The room fabric often dictates the location of these capillary tubes. Hiding the capillary tubes behind light fittings blending in with ceiling paintings or forming part of the ceiling sculptures can all be used to provide invisible smoke detection.In high volume atria applications such as cathedrals capillary sample points can be routed into the area at intermediate vertical levels to good effect to overcome stratification. The higher potential sensitivity of the VESDA system means that less smoke is required at the sample points to provide an alarm condition.Key FeaturesOptimising performanceTough and durableChemical resistance propertiesCompatible with VESDA VESDA-E ICAM FAAST Airsense and SecuritonLightweightPack of 10Please note The PIP-018 is equivalent to the REDAST025I.

GBP 47.63
1

Vesda Xtralis 25mm White System Test Point PIP-018-W

Vesda Xtralis 25mm White System Test Point PIP-018-W

Vesda Xtralis 25mm White System Test Point PIP-018-W Pack of 1025mm System Test Points are installed at the furthest point of the pipework and are used to introduce smoke in order to measure the time it takes for the smoke to reach the detectors. The maximum transport time is 120 seconds. They should always be connected withABS solvent cement.Key FeaturesMaterial ABSColour WhiteOperating temperature range -40C to 70CEN5425mmPack of 10Please note The PIP-018-W is equivalent to the WHTAST025I.

GBP 47.63
1

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda XtralisPIP-027Air Sampling Test Point with CapThey are designed to measure the transportation time a small quantity of smoke is introduced at the furthest point and the measurement in time is calculated from when the smoke enters the sampling point to when the ASD reacts. The maximum transport time is 120 seconds 2 minutes. Test points are the ideal solution for flexibility and convenience. They are installed at the end of the pipe run however for areas such as a lift shaft where accessibility is limited the pipe run can be brought into a riser.A key element of the VESDA system is its suction system which actively transports air from the protected area to the detector.The test point is for periodic smoke testing of the VESDA system for hard to reach areas.VESDA installations can be designed for the most complex areas using carefully selected shaped elements.The use of these shaped elements has a positive effect on the pneumatic system of the installation which translates into the unique and legendary quality of the VESDA system work in each pneumatic system.The suction installation is calculated with theASPIREprogramme.The program is used for modelling and visualization of aspiration installations class calculation in accordance with PN-EN-54-20.Please note The PIP-027 is equivalent to the REDAST025C.

GBP 7.49
1

Vesda Xtralis VSP-1007 VESDA-E VEA Stainless Steel Sampling Point Installation Tool

Vesda Xtralis VSP-1007 VESDA-E VEA Stainless Steel Sampling Point Installation Tool

Vesda Xtralis VSP-1007 VESDA-E VEA Stainless Steel Sampling Point Installation ToolThe VESDA-E VEA series of detectors combines VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional detectors. VEA detectors use air sampling points and multiple microbore air sampling tubes with three alarm sensitivity settings.The VESDA-E VEA stainless steel sampling point provides a more discreet smoke detection. Using a dedicated installation tool and perforated sampling area the VEA stainless steel sampling point provides a tamperproof solution that is ideal for correctional and educational applications.The low profile of the VEA stainless steel sampling point makes it ideal for installation in cabinets or narrow spaces.Fully interchangeable with the standard VSP-980 plastic sampling point the VEA stainless steel sampling point connects to 6mm VEA sampling tube via simple push fit connection to allow rapid and reliable installation.Patented VEA sampling point allows full tube integrity monitoring for centralised test and maintenance at the VEA detector significantly reducing ongoing maintenance time and cost.

GBP 86.32
1

VESDA-E VEA VSP-980-ST Stainless Steel Sampling Point

VESDA-E VEA VSP-980-ST Stainless Steel Sampling Point

VESDA-E VEA VSP-980-ST Stainless Steel Sampling PointThe VESDA-E VEA series of detectors combines VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional detectors. VEA detectors use air sampling points and multiple microbore air sampling tubes with three alarm sensitivity settings.The VESDA-E VEA stainless steel sampling point provides a more discreet smoke detection. Using a dedicated installation tool and perforated sampling area the VEA stainless steel sampling point provides a tamperproof solution that is ideal for correctional and educational applications. The low profile of the VEA stainless steel sampling point makes it ideal for installation in cabinets or narrow spaces.Fully interchangeable with the standard VSP-980 plastic sampling point the VEA stainless steel sampling point connects to 6mm VEA sampling tube via simple push fit connection to allow rapid and reliable installation.Patented VEA sampling point allows full tube integrity monitoring for centralised test and maintenance at the VEA detector significantly reducing ongoing maintenance time and cost.Key FeaturesTwo different types standard and surface mountAvailable in black or whiteFull supervisionAutomated cleaning by the detectorSwivel joint to allow optimum tube orientationModels to suite 6mm and 4mm microbore tubesDirect mount or ceiling tile mount with retainer housingEase of replacement

GBP 205.28
1

Vesda Xtralis VSP-1008 VESDA-E VEA Stainless Steel Sampling Duct Kit

Vesda Xtralis VSP-1008 VESDA-E VEA Stainless Steel Sampling Duct Kit

Vesda Xtralis VSP-1008 VESDA-E VEA Stainless Steel Sampling Duct KitOpen Duct Arrangement Sampling points are designed for use in open duct application by using VSP-1008 duct mounting kit. In open duct application these sampling points can be mounted onto duct kit using simple nut arrangement and then entire assembly can be mounted into open duct. This arrangement is recommended for open duct sizes from 4 to 12.The VESDA-E VEA series of detectors combines VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional detectors. VEA detectors use air sampling points and multiple microbore air sampling tubes with three alarm sensitivity settings.The VESDA-E VEA stainless steel sampling point provides a more discreet smoke detection. Using a dedicated installation tool and perforated sampling area the VEA stainless steel sampling point provides a tamperproof solution that is ideal for correctional and educational applications.The low profile of the VEA stainless steel sampling point makes it ideal for installation in cabinets or narrow spaces.Fully interchangeable with the standard VSP-980 plastic sampling point the VEA stainless steel sampling point connects to 6mm VEA sampling tube via simple push fit connection to allow rapid and reliable installation.Patented VEA sampling point allows full tube integrity monitoring for centralised test and maintenance at the VEA detector significantly reducing ongoing maintenance time and cost.

GBP 89.81
1

Vesda OSI-RE-SS OSID R Reflective Beam

Vesda OSI-RE-SS OSID R Reflective Beam

Vesda OSI-RE-SS OSID R Reflective BeamThe Vesda OSI-RE-SS is a 4-wire single-ended reflected type beam smoke detector that includes an 8 reflector and an integral sensitivity test.The Vesda OSI-RE-SS is a reflector-type linear optical beam smoke detector designed to operate as a component of fire alarm systems. The beam operates primarily on the principle of light obscuration utilising an Infra-Red beam. Optical beam smoke detectors are particularly appropriate for protecting buildings with large open spaces such as warehouses atriums etc.The OSI-RE-SS detector is a combined transmitterreceiver unit that can be directly connected to a conventional detector circuit.Key FeaturesCombined transmitter and receiver unit range 5-100 m 16-328 ftConventional modelReceiver consists of a CMOS imaging CCDWide 12 field of viewIntuitive beam alignment indicated by directional arrowsSingle IR wavelengthHighly resistant to building movement tolerates - 1 movementResistant to strong light sources does not alarm when saturated by sunResistant to large solid intruding objectsAutomatic sensitivity threshold level setting50 horizontal and 20 vertical beam alignmentBuilt-in heaterElectronic simulated smoke test from ground levelStandby fault and alarm LED indicators visible from the front and bottomAutomatic drift compensationPaintable coverRemovable plug-in terminal blocksOptional heater kit available for the reflectorThe Infra-Red transmitter and receiver Imager generates a beam of light towards a high efficiency reflector. The reflector returns the beam to the receiver where an analysis of the received signal is made. The change in the strength of the received signal is used to determine the alarm condition.The receiver imager has a wide FOV of 12 and tracks automatically the reflector in case of building movement or movement of its support structure. It is virtually impossible for the receiver to lose the reflector out of its side of view without any structural damage being caused to the building. As a result of this operation the OSI-RE-SS eliminates the number one cause of false alarms andor faults with traditional beam detectors.Optical filtering high-speed image acquisition and intelligent software algorithms provide the OSID-RE system with higher levels of stability and with greater resistance to high level lighting variability. As such the detector has a better resistance to sunlight and intruding objects in its FOV.The detector will not alarm when saturated by sunlight reflected sunlight or any other very bright light sources. In worst case the detector will go in to trouble and hence solving another cause of false alarms with traditional basic photocell receiver beam detectors. Thanks to the smoke imaging techniques the detector will not alarm for partial and sudden blockage.The alignment of the detector is extremely intuitive fast and accurate. Both the IR transmitter and the CMOS imager are contained in the eyeball that can turn freely in all directions. The eyeball moves - 20 in the vertical direction and 50 in the horizontal direction. Four arrows that indicate the direction to move the eyeball will guide the user to find the imagers perfect alignment with the reflector.To get started swiftly at long distances a laser tool can be inserted in the eyeball to allow finding the reflector quickly and then fine-tuning the eyeball to the optimum alignment. Once the optimum alignment is finalised signalled by all green arrows and LED the eyeball is locked by tightening the lever on its side. A paintable cover is then placed over the front to hide the alignment arrows locking mechanism and secures the locking lever in locked position. Unique in the market the sensitivity of the detector is selected and set automatically at the optimum sensitivity based on the size of the reflector measured in the FOV. The detector incorporates automatic drift compensation whereby the detector will adjust its detection thresholds in line with any long term signal reduction of the beam caused by contamination of the optical surfaces. An internal heating option is also provided on the Imager to prevent condensation on the optical surface.

GBP 870.91
1

Vesda-E VEU VEU-A10 4-Pipe Smoke Detector with 3.5quot Touchscreen Display

Vesda-E VEU VEU-A10 4-Pipe Smoke Detector with 3.5quot Touchscreen Display

Vesda-E VEU VEU-A10 4-Pipe Smoke Detector with 3.5 Touchscreen DisplayThe VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range 15 times greater than VESDA VLP and provision for more sampling holes provide an increased coverage in high airflow applications by up to 40.Considerably longer linear pipe runs and extended branched pipe network configurations cater perfectly to applications with higher ceilings providing an increased coverage by up to 80 whilst allowing convenient detector mounting for ease of service and maintenance. A range of revolutionary new features provide unsurpassed detection performance flexibility field programmability connectivity and reduced total cost of ownership.VEU features a robust IP40-rated enclosure and is equipped with a powerful aspirator that provides a total pipe length of 800 m 2624 ft. It is fully supported by the ASPIRE-E and Xtralis VSC software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.Key FeaturesShort wavelength laser based detectionInherent absolute calibrationAdvanced Imaging technology equivalentto thousands of sensorsClean air barrier for optics protectionMost robust contamination resistanceUltra-wide sensitivity rangeFlow fault thresholds configurable per portLong-life easy-to-replace filterQuiet operationLEDs for alarm and fault signalling3.5 colour touch screen for status reviewAdvanced remote diagnosticsArea coverage up to 6500m 69960ftUp to four inlet pipesTotal pipe length of 800m 2624ftSeven programmable relaysTwo GPIs monitored and unmonitoredUltrasonic flow sensingXtralis VSC VSM4 and ASPIRE-E PC software supportIP 40 enclosure not UL testedEasy mounting with optional steel supportbracketField replaceable aspirator sampling module filter anddetection chamberVESDAnet networkingEthernet 100 base TWiFi 802.11 bgnLocal host-mode USB portEasy cable termination accessEvent Log 20000 events

GBP 4616.03
1

Vesda-E VEU VEU-A00 Four Pipe Detector with LEDs Display - Silver

Vesda-E VEU VEU-A00 Four Pipe Detector with LEDs Display - Silver

Vesda-E VEU VEU-A00 Four Pipe Detector with LEDs Display - SilverThe VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range 15 times greater than VESDA VLP and provision for more sampling holes provide an increased coverage in high airflow applications by up to 40.Considerably longer linear pipe runs and extended branched pipe network configurations cater perfectly to applications with higher ceilings providing an increased coverage by up to 80 whilst allowing convenient detector mounting for ease of service and maintenance. A range of revolutionary new features provide unsurpassed detection performance flexibility field programmability connectivity and reduced total cost of ownership.VEU features a robust IP40-rated enclosure and is equipped with a powerful aspirator that provides a total pipe length of 800 m 2624 ft. It is fully supported by the ASPIRE-E and Xtralis VSC software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.Key FeaturesFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour alarm levels and an ultra-wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD icon display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningReferencing to accommodate external environmental conditions to minimise nuisance alarmsFully backward compatible with VLP and VESDAnetRemote monitoring with iVESDA for system review and proactive maintenanceEthernet for connectivity with Xtralis software for configuration secondary monitoring and maintenanceIndustry first. Aspirating detector secondary monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies enable faster service and maximum uptime

GBP 3893.45
1

Vesda-E VEP VEP-A00-P Four Pipe Detector with LEDs Display - Black

Vesda-E VEP VEP-A00-P Four Pipe Detector with LEDs Display - Black

Vesda-E VEP VEP-A00-P Four Pipe Detector with LEDs Display - BlackThe VESDA-E VEP series of smoke detectors bring the latest and most advanced detection technology to provide very early warning and the best nuisance alarm rejection to a wide range of applications. Built on the Flair detection technology and years of application experience VEP detectors deliver absolute calibration for lifetime performance and a range of revolutionary new features that deliver user value.The VESDA-E VEP series of aspirating smoke detectors extend the reach of the VESDA-E platform to a wide range of applications. VEP sensitivity range is from 0.005-20m 0.0015-6.25ft and provides up to 40 Class A holes. VEP provides linear pipe lengths up to 280 m 918 ft and up to 560 m 1837 ft of branched pipe networks. VEP also provides StaX and Analytics support together with Ethernet WiFi USB and VESDAnet capabilities.Key FeaturesOne and four pipe models for different applicationsFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour alarm levels and a wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD icon display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningReferencing to accommodate external environmental conditions to minimise nuisance alarmsFully backward compatible with VLP and VESDAnetRemote monitoring with iVESDA for system review and proactive maintenanceEthernet for connectivity with Xtralis software for configuration secondary monitoring and maintenanceIndustry first. Aspirating detector secondary monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies enable faster service and maximum uptime

GBP 2562.58
1

Vesda-E VEP VEP-A00-1P Single Pipe Aspiration Smoke Detector with LEDs Black

Vesda-E VEP VEP-A00-1P Single Pipe Aspiration Smoke Detector with LEDs Black

Vesda-E VEP VEP-A00-1P Single Pipe Aspiration Smoke Detector with LEDs BlackThe VESDA-E VEP series of smoke detectors bring the latest and most advanced detection technology to provide very early warning and the best nuisance alarm rejection to a wide range of applications. Built on the Flair detection technology and years of application experience VEP detectors deliver absolute calibration for lifetime performance and a range of revolutionary new features that deliver user value.The VESDA-E VEP series of aspirating smoke detectors extend the reach of the VESDA-E platform to a wide range of applications. VEP sensitivity range is from 0.005-20m 0.0015-6.25ft and provides up to 40 Class A holes. VEP provides linear pipe lengths up to 280 m 918 ft and up to 560 m 1837 ft of branched pipe networks. VEP also provides StaX and Analytics support together with Ethernet WiFi USB and VESDAnet capabilities.Key FeaturesFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour alarm levels and a wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD icon display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningReferencing to accommodate external environmental conditions to minimize nuisance alarmsFully backward compatible with VLP and VESDAnetRemote monitoring with iVESDA for system review and proactive maintenanceEthernet for connectivity with Xtralis software for configuration monitoring and maintenanceIndustry first ASD monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies faster service and maximum uptimeArea Coverage 2000 m2 21500 sq. ftApplicationsAccommodation Apartments Hotels Shops and OfficesCorrectional FacilitiesClean RoomsCold StorageCulturalHeritageData TelecomEducationHospitals HealthcareInsuranceMarineNuclear FacilitiesOfficesOil GasPortable Switch RoomsPower GenerationRecords StorageRetailTransportationWind Power GenerationWarehousing

GBP 2002.13
1

Vesda-E VEP VEP-A10-P 4 Pipe Detector with 3.5quot Touch Screen Display - Black

Vesda-E VEP VEP-A10-P 4 Pipe Detector with 3.5quot Touch Screen Display - Black

Vesda-E VEP VEP-A10-P Four Pipe Detector with 3.5 Touch Screen Display- BlackThe VESDA-E VEP series of smoke detectors bring the latest and most advanced detection technology to provide very early warning and the best nuisance alarm rejection to a wide range of applications. Built on the Flair detection technology and years of application experience VEP detectors deliver absolute calibration for lifetime performance and a range of revolutionary new features that deliver user value.The VESDA-E VEP series of aspirating smoke detectors extend the reach of the VESDA-E platform to a wide range of applications. VEP sensitivity range is from 0.005-20m 0.0015-6.25ft and provides up to 40 Class A holes. VEP provides linear pipe lengths up to 280 m 918 ft and up to 560 m 1837 ft of branched pipe networks. VEP also provides StaX and Analytics support together with Ethernet WiFi USB and VESDAnet capabilities.Key FeaturesOne and four pipe models for different applicationsFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour alarm levels and a wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD icon display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningReferencing to accommodate external environmental conditions to minimise nuisance alarmsFully backward compatible with VLP and VESDAnetRemote monitoring with iVESDA for system review and proactive maintenanceEthernet for connectivity with Xtralis software for configuration secondary monitoring and maintenanceIndustry first. Aspirating detector secondary monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies enable faster service and maximum uptime

GBP 3023.30
1

Vesda Xtralis OSE-HP-01 OSID Emitter - High Power - Alkaline Battery

Vesda Xtralis OSE-HP-01 OSID Emitter - High Power - Alkaline Battery

Vesda Xtralis OSE-HP-01 OSID Emitter - High Power - Alkaline BatteryOpen-area Smoke Imaging Detection OSID is an innovative system for reliable cost-effective smoke detection for large open spaces requiring standard sensitivity detection.In its simplest configuration OSID uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm.Key FeaturesMaximum detection range of 150 m 492 ft for the OSI-10Dual wavelength LED-based smoke detectionOptical imaging with CMOS imaging chipOn-board event log for fault and alarm diagnosticsHigh tolerance to false alarm due to building movementHigh tolerance to transient dust steam and intrusion of solid objectsEasy alignment with large adjustment and viewing anglesNo need for precise alignmentTolerant of alignment driftAutomatic commissioning in under ten minutesSimple DIP switch configurationSimple and easy maintenance requirementsThree selectable alarm thresholdsStatus LEDs for Fire Trouble and PowerConventional alarm interface for straightforward fire system integration

GBP 326.59
1

Vesda-E VEA 6mm Black Surface Sampling Point pack of 22 VSP-982-B22

Vesda-E VEA 6mm Black Surface Sampling Point pack of 22 VSP-982-B22

Vesda-E VEA 6mm Black Surface Sampling Point pack of 22 VSP-982-B22VEA sampling points are available in two different types surface mount and standard mount. The Surface mount sampling points are designed for use where access to the ceiling void is limited.Microbore tubes are run along the ceiling visible in the protected area. These sampling points are screwed directly to the ceiling. Surface mount sampling points are available in black or white with 4mm or 6mm inlets to suit appropriate microbore tubes.The VESDA-E VEA series of detectors combines VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional spot detectors. VEA detectors use patented air sampling points and multiple microbore air-sampling tubes with three alarm sensitivity settings.Each patented VEA sampling point and microbore tube is fully supervised by the detector. End to end supervision combined with system integrity monitoring reduces VEA system servicing and maintenance time by 90 compared to typical spot detection solutions.Key FeaturesTwo different types standard and surface mountAvailable in black or whiteFull supervisionAutomated cleaning by the detectorSwivel joint to allow optimum tube orientationModels to suite 6mm and 4mm microbore tubesDirect mount or ceiling tile mount with retainer housingEase of replacementApplications used forHealthcareOfficesEducationRetailPrisonsApartments residentialElectrical cabinets

GBP 446.74
1

Vesda-E VEA VSP-983-W 4mm White Surface Sampling Point

Vesda-E VEA VSP-983-W 4mm White Surface Sampling Point

Vesda-E VEA VSP-983-W 4mm White Surface Sampling PointVEA sampling points are available in two different types surface mount and standard mount. The Surface mount sampling points are designed for use where access to the ceiling void is limited.Microbore tubes are run along the ceiling visible in the protected area. These sampling points are screwed directly to the ceiling. Surface mount sampling points are available in black or white with 4mm or 6mm inlets to suit appropriate microbore tubes.The VESDA-E VEA series of detectors combines VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional spot detectors. VEA detectors use patented air sampling points and multiple microbore air-sampling tubes with three alarm sensitivity settings.Each patented VEA sampling point and microbore tube is fully supervised by the detector. End to end supervision combined with system integrity monitoring reduces VEA system servicing and maintenance time by 90 compared to typical spot detection solutions.Key FeaturesTwo different types standard and surface mountAvailable in black or whiteFull supervisionAutomated cleaning by the detectorSwivel joint to allow optimum tube orientationModels to suite 6mm and 4mm microbore tubesDirect mount or ceiling tile mount with retainer housingEase of replacementApplications used forHealthcareOfficesEducationRetailPrisonsApartments residentialElectrical cabinets

GBP 14.99
1

Vesda-E VEA VEA-040-A10 40-Tube Addressable Detector with 3.5quot Touchscreen Display

Vesda-E VEA VEA-040-A10 40-Tube Addressable Detector with 3.5quot Touchscreen Display

Vesda-E VEA VEA-040-A10 40-Tube Addressable Detector with 3.5 Touchscreen DisplayThe VESDA-E VEA-040-A10 is an aspirating smoke detector ASD that provides early warning of fire conditions by drawing air samples through a multi-hole addressable microbore tube air-sampling network.The detector easily interfaces with fire warning and fire suppression release systems and can be integrated into a building management system BMS.Key FeaturesThe VEA-040-A10 detector contains the following featuresPinpoint addressability with superior detection compared to spot detectors40 addressable microbore tubes with individual sampling pointsAssured detection with end to end system integrity monitoringInterruption-free business operation with centralized testing and maintenanceSingle sampling point or single tube blockage detectionAutomatic sampling point cleaningThree sensitivity settings for the sampling pointsVariable length capillary tubes up to 100 m 328 ftLaser-based absolute smoke detectionDual stage filtering and clean air barrier for optics protectionReliable linear pump technologyLEDs for alarm and fault signalling3.5 colour touch screen for status reviewSeven programmable relaysTwo GPIs monitored and unmonitoredPC software supportiVESDA app for system monitoring on mobile devicesIP 40 enclosure not UL testedEasy mounting with steel support bracketField replaceable filter smoke sensor module pump and rotary valveVESDAnet networkingEthernet 100 base TWiFi 802.11 bgnLocal host-mode USB portEasy cable termination accessEvent Log 20000 events

GBP 8241.78
1