ProfitSpring | B2B PPC Agency

Vimpex HSRP-S-8-230 Hydrosense HS Conventional Repeater panel 8 zone 230 VAC

Vimpex HSRP-S-8-230 Hydrosense HS Conventional Repeater panel 8 zone 230 VACHydrosense HS Conventional Repeater panel 8 zone 230 VAC

GBP 726.80

1

Vimpex IDAP-LEC Hydrosense Addressable Water Leak Detection Panel Single Loop Expansion Card

Vimpex IDAP-LEC Hydrosense Addressable Water Leak Detection Panel Single Loop Expansion CardThe Vimpex Hydrosense addressable water leak detection panel can have an additional single loop expansion card.

GBP 768.06

1

Vimpex HYCP-Bezel Hydrosense Bezel for Semi-Flushing Panel and Repeater to Wall

Vimpex HYCP-Bezel Hydrosense Bezel for Semi-Flushing Panel and Repeater to Wall The HYCP-Bezel is a Hydrosense Bezel for Semi-Flushing Panel and Repeater to a wall.

GBP 107.69

1

Vimpex Hydrosense ID Addressable Dual Loop Leak Detection Panel

Vimpex Hydrosense ID Addressable Dual Loop Leak Detection PanelSingle and dual loop panels are available with each loop supporting a maximum of 127 addressable devices. Our highly versatile leak detection module will support up to 50m of Hydro-Wire or one Hydro-Probe per circuit with two circuits available per device.Control panel configuration also allows each leak detection module to be allocated a location-specific name. Hydrosense ID Control Panels are equipped with both common Alarm and Fault relays as well as battery backup.Key FeaturesBoth single and dual loop control panels availableA dual loop panel can support in excess of 500 Hydro-Probes and over 25000 m of Hydro-WireControl panel configuration allows each addressable device to be uniquely identifiedRemote outputs now fully configurableRS485 panel expansion bus supporting up to 32 additional accessoriesCause and Effect output control via Loop Explorer 2 PC softwareFully monitored sounder circuitsBattery Standby

GBP 2106.38

1

Vimpex IC38230 IdentiCryer 8 Zone Conventional Panel

Vimpex IC38230 IdentiCryer 8 Zone Conventional PanelThe Identi-Cryer Lockdown Control panel is designed to help create a notification system in the event of an emergency situation within a building these emergency situations can relate to any instances in and around the building which require building occupants to carry out a Lockdown procedure. The panel is continuously monitoring for faults 24 hours a day and has the facility for 24-hour battery standby in the event of power failuresKey FeaturesSimple to install and maintainCommon fault and alarm relay contacts availableUp to 72 hour battery standby

GBP 495.56

1

Vimpex IC32230 IdentiCryer 2 Zone Conventional Panel

Vimpex IC32230 IdentiCryer 2 Zone Conventional PanelThe Identi-Cryer Lockdown Control panel is designed to help create a notification system in the event of an emergency situation within a building these emergency situations can relate to any instances in and around the building which require building occupants to carry out a Lockdown procedure. The panel is continuously monitoring for faults 24 hours a day and has the facility for 24-hour battery standby in the event of power failuresKey FeaturesSimple to install and maintainCommon fault and alarm relay contacts availableUp to 72 hour battery standby

GBP 385.44

1

Vimpex IC34230 IdentiCryer 4 Zone Conventional Panel

Vimpex IC34230 IdentiCryer 4 Zone Conventional PanelThe Identi-Cryer Lockdown Control panel is designed to help create a notification system in the event of an emergency situation within a building these emergency situations can relate to any instances in and around the building which require building occupants to carry out a Lockdown procedure. The panel is continuously monitoring for faults 24 hours a day and has the facility for 24-hour battery standby in the event of power failuresKey FeaturesSimple to install and maintainCommon fault and alarm relay contacts availableUp to 72 hour battery standby

GBP 440.50

1

Vimpex IDAP-S-1-230 Hydrosense ID Addressable Single Loop Leak Detection Panel

Vimpex IDAP-S-1-230 Hydrosense ID Addressable Single Loop Leak Detection PanelSingle and dual loop panels are available with each loop supporting a maximum of 127 addressable devices. Our highly versatile leak detection module will support up to 50m of Hydro-Wire or one Hydro-Probe per circuit with two circuits available per device.Control panel configuration also allows each leak detection module to be allocated a location-specific name. Hydrosense ID Control Panels are equipped with both common Alarm and Fault relays as well as battery backup.Key FeaturesBoth single and dual loop control panels availableA single loop panel can support up to 254 Hydro-Probes or over 12000 m of Hydro-WireControl panel configuration allows each addressable device to be uniquely identifiedRemote outputs now fully configurableRS485 panel expansion bus supporting up to 32 additional accessoriesCause and Effect output control via Loop Explorer 2 PC softwareFully monitored sounder circuitsBattery Standby

GBP 1438.50

1

Vimpex HSRP-S-2-230 Hydrosense HS Conventional Repeater Panel 2 Zone 230 VAC

Vimpex HSRP-S-2-230 Hydrosense HS Conventional Repeater Panel 2 Zone 230 VACHydrosense HS Conventional Repeater panel 2 zone 230 VACDescriptionThe Hydrosense HS conventional system offers both linear and point detection solutions through both the Hydro-Wire and Hydro-Probe. Control Panel sizes range from two to eight detection zones and each model includes two sounder circuits. An Ancillary PCB can also be fitted to provide local plant control or BMS integration via up to 8 zonal relay contacts.A seamless operation is assured by both battery backup and system fault monitoring. An alarm andor fault condition will be signaled both visually and audibly. Hydrosense HS is ideal for small to medium sized projects with up to 50 metres of Hydro-Wire or 20 Hydro-Probes allowed per detection zone.Key FeaturesFully monitored alarm and detection circuitsNew robust junction and connection boxeswith plug n play featureSimple to install and maintainNew Hydro-Wire incorporates both enhanced durability andflexibilityUp to 72 hour battery standbyNew probes include enhanced aesthetics and mechanical protectionCommon fault and alarm relay contacts availableConnection and termination made even more simple

GBP 555.00

1

Vimpex Hydrosense HS Conventional 2 Zone Leak Detection Panel with Ancillary PCB

Vimpex Hydrosense HS Conventional 2 Zone Leak Detection Panel with Ancillary PCB 230v AC - HSCP-S-2-AP-230The new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.The ancillary PCB provides common fire common fault coincidence and zonal fire volt free contacts allowing control of sub-systems graphical mimics and plant remotely from the main panel over a two-wire data bus.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 963.74

1

Vimpex Hydrosense HS Conventional 4 Zone Leak Detection Panel with Ancillary PCB

Vimpex Hydrosense HS Conventional 4 Zone Leak Detection Panel with Ancillary PCB 230v ACThe new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.The ancillary PCB provides common fire common fault coincidence and zonal fire volt free contacts allowing control of sub-systems graphical mimics and plant remotely from the main panel over a two-wire data bus.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 1060.12

1

Vimpex Hydrosense HS Conventional 8 Zone Leak Detection Panel with Ancillary PCB

Vimpex Hydrosense HS Conventional 8 Zone Leak Detection Panel with Ancillary PCB 230v ACThe new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.The ancillary PCB provides common fire common fault coincidence and zonal fire volt free contacts allowing control of sub-systems graphical mimics and plant remotely from the main panel over a two-wire data bus.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 1193.57

1

Vimpex Hydrosense HS Conventional 4 Zone Leak Detection Panel 230VAC

Vimpex Hydrosense HS Conventional 4 Zone Leak Detection Panel 230VACThe new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 582.32

1

Vimpex Hydrosense HS Conventional 2 Zone Leak Detection Panel

Vimpex Hydrosense HS Conventional 2 Zone Leak Detection PanelThe new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 519.97

1

Vimpex Hydrosense HS Conventional 8 Zone Leak Detection Panel

Vimpex Hydrosense HS Conventional 8 Zone Leak Detection PanelThe new Hydrosense systems provide both linear detection using Hydrowire and point detection using probes. Linear detection Hydrowire is a flexible cable which will continuously monitor large areas. When even a small amount of water or moisture comes into contact with Hydrowire it will trigger an alarm. Point detection is provided by Hydrosense floor or drip tray probes these are fixed to the floor or drip tray and adjusted to give the required detection level and connected to the control panel via a Hydrosense water leak detection module.Utilising life safety technology in the design of Hydrosense provides the reliability and integrity of BSi approved fire detection systems meaning there is virtually no risk of failure downtime and significantly fewer false alarms.Key FeaturesIdeal for small and medium sized installations2 4 and 8 Zone Control Panels available with all variants featuring battery standby as well as common fault and alarm relay contactsSimple to install and maintainDetection and Sounder circuits constantly monitored for faultsRS485 data bus allows both zonal contacts and repeater panels to be incorporatedBattery Backup

GBP 706.87

1

Vimpex HSRP-S-4-230 Hydrosense HS Conventional Repeater panel 4 zone 230 VAC

Vimpex HSRP-S-4-230 Hydrosense HS Conventional Repeater panel 4 zone 230 VACThe Hydrosense HS conventional supports both linear and point detection with Hydrowire and Hydrosense Probes. Control Panel sizes range from two to eight detection zones and each model includes two sounder circuits. An Ancillary PCB can also be fitted to provide local plant control or BMS integration via up to 8 zonal relay contacts.Key FeaturesFully monitored alarm and detection circuitsNew robust junction and connection boxes with plug n play featureSimple to install and maintainNew Hydro-Wire incorporates both enhanced durability and flexibilityUp to 72 hour battery standbyNew probes include enhanced aesthetics and mechanical protectionCommon fault and alarm relay contacts availableConnection and termination made even more simpleSpecificationsMains Supply 230 V ac 100 Watts Max.Mains Supply Fuse I.6 A 250 VOutput Voltage 18.5 to 29 V dcBattery Size Max 12 V 7 Nh 2 batteries are requiredBattery charge Voltage 27.6 V dc NominalBattery charge Current 0.7 ABattery lead fuse 20 mm 3.15 ADedicated Sounder Circuits 24 V dc fused at S00 mARelay contact rating 30 V dc 1 ADetection Circuit EOL 6800 Ohms 0.50 WSounder Circuit EOL 10000 Ohms 0.25 WIP Rating 30Construction 1.2 mm Mild SteelFinish Epoxy Powder CoatedColour RAL 7047 Light Grey - SatinDimensions L x H x D 385 x 3 I 0 x 90 mm.

GBP 599.77

1

Vimpex IDAP-S-R-230 Hydrosense ID Addressable Leak Detection Repeater Panel 230VAC

Vimpex IDAP-S-R-230 Hydrosense ID Addressable Leak Detection Repeater Panel 230VACThe Mains Relay Controller is capable of switching a 250Vac 5A load and is ideal for controlling solenoid valves or plant equipment.The ID-WLMRC is a loop driven addressable device and can be integrated into our powerful Cause and Effect matrix. The addressable element also allows the user to allocate the device with a location-specific name.A single input is also provided on the device in addition to the addressable circuit and providing a closed contact to this input will result in the relay being energised. This makes it ideal for connection to a Manual Call Point or for signalling from other pieces of equipment.

GBP 1294.66

1

Vimpex IDAP-S-R-24 Hydrosense ID Addressable Leak Detection Repeater Panel 24VDC

Vimpex IDAP-S-R-24 Hydrosense ID Addressable Leak Detection Repeater Panel 24VDCThe Mains Relay Controller is capable of switching a 250Vac 5A load and is ideal for controlling solenoid valves or plant equipment.The ID-WLMRC is a loop driven addressable device and can be integrated into our powerful Cause and Effect matrix. The addressable element also allows the user to allocate the device with a location-specific name.A single input is also provided on the device in addition to the addressable circuit and providing a closed contact to this input will result in the relay being energised. This makes it ideal for connection to a Manual Call Point or for signalling from other pieces of equipment.

GBP 980.24

1

Vimpex HY-KEY Spare Enable Key for Hydrosense Panel

Vimpex HY-KEY Spare Enable Key for Hydrosense PanelThe HY-KEY is a spare Enable Key designed for use with Hydrosense Panels.

GBP 12.98

1

Vimpex HY-VRF Hydrosense Control Relay White - Flush Mount with Blue LED Indicator

Vimpex HY-VRF Hydrosense Control Relay White - Flush Mount with Blue LED IndicatorProvides integration between Hydrosense Control Panels and Water Flow Control equipment. Rated at 230 V ac and activated via 24 V dc input.The Hydrosense Control Relay would typically be operated via the on-board panel alarm relay and power derived from either the panel auxiliary supply or a local 24 V PSU. Provides a volt free interface to operate third party equipment in a water leak condition.Features a blue LED that will illuminate when the relay has been energized.Key FeaturesIdeal for new or retrofit projectsCan switch voltages upto 250 V ac at 8 AVersatile backbox featuring 10 fixing points to allow easy mounting. surface mount variants onlyIncorporates 4 x round 20 mm knockouts and 1 x rectangular for surface conduit. surface mountvariants onlyFlush or surface mounted

GBP 23.28

1

Vimpex HY-VRS Hydrosense Control Relay White - Surface Mount with Blue LED Indicator

Vimpex HY-VRS Hydrosense Control Relay White - Surface Mount with Blue LED IndicatorProvides integration between Hydrosense Control Panels and Water Flow Control equipment. Rated at 230 V ac and activated via 24 V dc input.The Hydrosense Control Relay would typically be operated via the on-board panel alarm relay and power derived from either the panel auxiliary supply or a local 24 V PSU. Provides a volt free interface to operate third party equipment in a water leak condition.Features a blue LED that will illuminate when the relay has been energized.Key FeaturesIdeal for new or retrofit projectsCan switch voltages upto 250 V ac at 8 AVersatile backbox featuring 10 fixing points to allow easy mounting. surface mount variants onlyIncorporates 4 x round 20 mm knockouts and 1 x rectangular for surface conduit. surface mountvariants onlyFlush or surface mounted

GBP 24.56

1

Vimpex HS-WLRI-F Hydrosense Conventional Remote Indicator

Vimpex HS-WLRI-F Hydrosense Conventional Remote IndicatorThe Hydrosense HS conventional supports both linear and point detection with Hydrowire and Hydrosense Probes.The Control Panel sizes range from two to eight detection zones and each model includes two sounder circuits.An Ancillary PCB can also be fitted to provide local plant control or BMS integration via up to 8 zonal relay contacts.

GBP 10.42

1

Vimpex SC-001 SmartCage 205x145x65mm

Vimpex SC-001 SmartCage 205x145x65mmSmartCage protects essential Fire Safety and Security equipment from theft vandalism or accidental damage.Constructed from PVC coated 4mm steel bar these tough resilient waterproof cages provide security for a wide range of devices.Key FeaturesSmart design and construction for a tough heavy-duty cageIndoor or outdoor applicationsFlush and surface mount installation optionsBespoke design and manufacture serviceOptional stainless-steel constructionSupplied with heavy duty easy install quick fit clamps and screwsProtects smoke detectors clocks fire alarm bells etc. from unwanted damageThick gauge wiring for maximum strength and durabilityCertified for UK prison usePlease note The image is for illustrative purposes only. The detector is not included.

GBP 22.38

1

Vimpex CBE6OTD ClamBell One Touch Demo - Deep Base - Red - Standard Print

Vimpex CBE6OTD ClamBell One Touch Demo - Deep Base - Red -Standard PrintManufactured by Vimpexin the UK the ClamBell EN54-3 approved fire bell incorporates traditional andinnovative design.The hinged design of ClamBell means installers benefit fromreduced installation time under 2 minutes. Once fitted to the wall and wiredto the circuit ClamBell clicks shut.Low power consumption and good sonorous tone result from useof an aluminium gong which also significantly reduces weight.Three mounting versions are available - shallow base deepbase and purpose designed weatherproof option.Key Features24V powered red conventional fire alarm bellDeep mounting baseSlick and modern designPermanently fitted aluminium gong with sonorous toneReduced installation time Range of mounting options available for various applicationsEN54-3 approved

GBP 73.42

1

Vimpex SBE6-RS-024-EN-RW StroBell Combined Fire Alarm Bell amp Visual Indicating Device

VimpexSBE6-RS-024-EN-RWStroBell Combined Fire Alarm Bell Visual Indicating DeviceManufactured by Vimpex in the UK the StroBell is a combined fire alarm bell and visual indicating device which is ideal for installations that require both a traditional bell tone as well as a visual alarm.The StroBell uses the same hinged design as the ClamBell meaning installers benefit from reduced installation time. Once fitted to the wall and wired to the circuit the StroBell clicks shut.With an ultra bright LED the StroBell offers flexibility to the installer by offering different options for brightness and flash frequency.Key FeaturesUltra bright LEDDifferent options for brightness and flash frequencySame easy installation as ClamBellSlick and modern lookingStroBell strobe and bell can operate independently or combined

GBP 105.68

1

Brand

Merchant

Price (EUR)