ProfitSpring | B2B PPC Agency

Global Fire Equipment 3-LC-CHAMELEON Chameleon 3 Loop Card

Global Fire Equipment 3-LC-CHAMELEON Chameleon 3 Loop CardA 3 loop card for the Global Fire Equipment Chameleon Repeater Panel.

GBP 446.27

1

Notifier ID3000 Basic Equipment Kit 2-8 Loops 020-538

Notifier ID3000 Basic Equipment Kit 2-8 Loops 020-538The 020-538 is a spare replacement LPCB approved Basic Equipment Kit for the Notifier ID3000 panel. This basic equipment kit comes as standard with two loops but can be expanded up to 8 loops with the use of additional loop cards. This part is not a complete panel but replacement basic equipment kit for an existing panel.

GBP 1972.84

1

Global Fire Equipment 4-LC-CHAMELEON Chameleon 4 Loop Card

Global Fire Equipment 4-LC-CHAMELEON Chameleon 4 Loop CardA 4 loop card for the CHAMELEON range of panels.

GBP 601.49

1

Global Fire Equipment GFE-SWR-IR3 Sense-Ware IR3 Flame Detector

Global Fire Equipment GFE-SWR-IR3 Sense-Ware IR3 Flame DetectorGFE-SWR flame detector range utilizes a microprocessor for sophisticated electronic signal analysis. Its advanced discrimination technology and rugged construction makes it suitable for almost all installations scenarios.GFE-SWR-IR3 flame detector must exceed its alarm threshold to initiate a fire alarm.The GFE-SWR-IR3 flame detector also use additional alarm criterion the analysis of the flame flicker-frequency. This version also exhibits good false alarm rejection capabilities.Key FeaturesSuitable for heavy and light Hydrocarbons such as Gasoline Diesel Methanol and EthanolResistant to artificial and sunlightSuitable for indoor and outdoor applicationsGRP IP65 housingRelay output for Alarm and Fault conditionsCPREN54-10 certifiedATEX zone 222 certifiedFM3260 3611 ApprovalsRugged sensors make the detector suitable for virtually all fire typesSophisticated software enhances the reliability and availability of the detectorDesign of the housing and the swivel mount avoid mounting errors with regards to groundingAutomatic Sensor Test Built-in Self-Test enhances the reliability and availability of the flame detectorPressure Compensating Element avoids additional cost of maintenance caused by moisture build up and increases the life time

GBP 2268.94

1

Global Fire Equipment GFE-SWR-UV Sense-Ware UV Flame Detector

Global Fire Equipment GFE-SWR-UV Sense-Ware UV Flame DetectorGFE-SWR flame detector range utilizes a microprocessor for sophisticated electronic signal analysis. Its advanced discrimination technology and rugged construction makes it suitable for almost all installations scenarios.The GFE-SWR-UV flame detector is suitable for indoor applications such as fume hoods and hydrogen storages. Because of its non-corrosive housing it is suitable for indoor industrial areas where corrosion may occur. UV light is emitted in practically every fire both hydrocarbon and non-hydrocarbon fires.Key FeaturesSuitable for heavy and light Hydrocarbons such as Gasoline Diesel Methanol and EthanolResistant to artificial and sunlightSuitable for indoor and outdoor applicationsGRP IP65 housingRelay output for Alarm and Fault conditionsCPREN54-10 certifiedATEX zone 222 certifiedFM3260 3611 ApprovalsRugged sensors make the detector suitable for virtually all fire typesSophisticated software enhances the reliability and availability of the detectorDesign of the housing and the swivel mount avoid mounting errors with regards to groundingAutomatic Sensor Test Built-in Self-Test enhances the reliability and availability of the flame detectorPressure Compensating Element avoids additional cost of maintenance caused by moisture build up and increases the life time

GBP 1592.06

1

Global Fire Equipment GFE-SWR-UVIR Sense-Ware UVIR Flame Detector

Global Fire Equipment GFE-SWR-UVIR Sense-Ware UVIR Flame DetectorGFE-SWR flame detector range utilizes a microprocessor for sophisticated electronic signal analysis. Its advanced discrimination technology and rugged construction makes it suitable for almost all installations scenarios.GFE-SWR-UVIR flame detector is a combination of UV and IR detections it uses an additional alarm criterion the analysis of the flame flicker frequency. The UV and IR sensor must both exceed their alarm threshold to initiate a fire alarm. The GFE-SWR-UVIR flame detector has a good false alarms immunity since the UV and IR sensor do not share false alarm sources.Key FeaturesSuitable for heavy and light Hydrocarbons such as Gasoline Diesel Methanol and EthanolResistant to artificial and sunlightSuitable for indoor and outdoor applicationsGRP IP65 housingRelay output for Alarm and Fault conditionsCPREN54-10 certifiedATEX zone 222 certifiedFM3260 3611 ApprovalsRugged sensors make the detector suitable for virtually all fire typesSophisticated software enhances the reliability and availability of the detectorDesign of the housing and the swivel mount avoid mounting errors with regards to groundingAutomatic Sensor Test Built-in Self-Test enhances the reliability and availability of the flame detectorPressure Compensating Element avoids additional cost of maintenance caused by moisture build up and increases the life time

GBP 1897.13

1

Global Fire Equipment OWL-6-OFFLINE OWL Graphical Software 6 Panels Offline

Global Fire Equipment OWL-6-OFFLINE OWL Graphical Software6 Panels OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during systemcommissioning devices icons may be placed on these drawings for easy alarmidentification. Therefore in an alarm condition the exact allocation of thealarm can be displayed in a graphical manner.The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 3434.39

1

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - Anthracite

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - AnthraciteThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable ChassisBlack version

GBP 1518.88

1

Global Fire Equipment OWL-1-OFFLINE OWL Graphical Software - 1 Panel Offline

Global Fire Equipment OWL-1-OFFLINE OWL Graphical Software - 1 Panel OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1479.05

1

Global Fire Equipment OWL-1-ONLINE OWL Graphical Software - 1 Panel Online

Global Fire Equipment OWL-1-ONLINE OWL Graphical Software -1 Panel OnlineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1303.57

1

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop Control Panel Anthracite

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop ControlPanel AnthraciteThe GEKKO Fire Alarm Control Panel is the successor to GFEswell-known JUNIOR V4 panel.The GEKKO can have from 1 to 4 addressable loops. It ishoused in a functional ABS plastic enclosure with only two screws used toclose and secure the lid.The new graphic backlit LCD display can accommodate any typeof custom characters or graphic symbols allowing multi-language support aswell as visual and customisable elements.It can communicate with our proprietary ODYSSEY GraphicsInterface as well as with third party Building Management Systems through aModbus output. It is also capable of communicating with a repeater unit usingany of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space to install up to 7 AH 24VDC Sealed Lead Acid backup batteries providing battery supply to the GEKKO andZEOS associated devices which boast extremely low energy consumption.The Cause and Effect programming as well as allcustomer-specific configuration is introduced in the GEKKO using the CHAMELEONCONNECTOR software which is then downloaded to the flash memory of the unit.Key FeaturesSuccessor to GFEs JUNIOR V4 panel1 to 4 loop panel 2 loop cards installedSupports connection to Repeaters via RS422 Fibre-Optic orTCPIPNetworkable panel compatible with OCTO and NODE range ofpanelsUp to 250 devices per loop only 125 addresses availableUp to 95 VULCAN 2 addressable ultra low current basesounders 32 address limit32 individually programmable sounder addressesFull self-addressable devices support2 Fire output relays change-over and 1 fault relay NC -opens on fault2 conventional alarm outputs Individually programmableBoth detection loops monitored for integrity512 fully programmable sounder and IO groups384 fully programmable zonesEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all GFE manufactured ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indicationEN54-13 EN54-2 EN54-4 1328-CPR-0737 certified

GBP 671.47

1

Global Fire Equipment OWL-2-5-ONLINE OWL Graphical Software - 2 -5 Panels Online

Global Fire Equipment OWL-2-5-ONLINE OWL Graphical Software - 2 -5 Panels OnlineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1955.34

1

Global Fire Equipment OWL-2-5-OFFLINE OWL Graphical Software - 2 -5 Panels Offline

Global Fire Equipment OWL-2-5-OFFLINE OWL Graphical Software - 2 -5 Panels OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 2130.83

1

Carrier EST_FlyCase Demo Set For EST Compact

Carrier EST_FlyCase Demo Set For EST CompactThis demo set is only dedicated for demo purposes training presentation. It must not be used for projects. No certification covers this equipment for real purposes.This Demo equipment includes a full set of mounted devices into a single RackEST-VES-4002-LNRHandle_Flycase

GBP 5164.81

1

Patol DFA 25-3 Detonation Flame Arrester for Explosion Zones category IIC 0.101557P

Patol DFA 25-3 Detonation Flame Arrester for Explosion Zones category IIC 0.101557PDetonation flame arrester for explosion zones. Equipment category IIB eg. Hydrogen.2 pieces are needed per sampling tube.

GBP 3815.99

1

Howler SH03 SafetyHub cw Signage and Siteplan Holder

Please note Additional shipping charges apply to this product.Howler SH03 SafetyHub cw Signage and Siteplan HolderRaising the alert quickly in the event of a fire and having the appropriate equipment on hand to deal with it remains of utmost importance on every construction site. Be prepared and be proactive The SafetyHub FirePost sets the standard for effective site fire safety.Key FeaturesULTRA-TOUGH it stands out and stands upTIDY all the kit is in one neat unitPROTECTED ensures the equipment is always readyCOMPATIBLE with all Howler alarm systems

GBP 549.32

1

Notifier 020-543 Dual Transmission Path Board Kit

Notifier 020-543 Dual Transmission Path Board KitThe 020-543 includes complete PSU interface unit assembly. Interconnection cables and spare fuses. Mounts behind the basic equipment chassis. Essential for use with 7A PSU.

GBP 631.12

1

EMS FC-KD25250 Dual Output 24v DC 2.5A Power Supply

EMS FC-KD25250 Dual Output 24v DC 2.5A Power SupplyThe K25000 series are combined power supply and battery chargers designed to be used for fire alarm control and indicating equipment complying with EN54-2 and EN54-4. K25400 models are fitted with a 5.25A power supply and K25250 models are fitted with a 2.5A power supply.To satisfy the requirement of clause 6.4 of EN54-4 for fire alarm Power Supply Equipment mounted in a separate enclosure to the Control and Indicating Equipment a separate interface RPSM2 needs to be fitted inside the PSE enclosure which provides two transmission paths between the PSE and the CIE to enable one transmission path to continue to operate in the event of failure of the other. This board is fitted to models with the KD prefix to the part number. The D denoting that the dual output board is fitted.

GBP 531.30

1

EMS FC-KD25400 Dual Output 24v DC 5.25A Power Supply

EMS FC-KD25400 Dual Output 24v DC 5.25A Power SupplyThe K25000 series are combined power supply and battery chargers designed to be used for fire alarm control and indicating equipment complying with EN54-2 and EN54-4. K25400 models are fitted with a 5.25A power supply and K25250 models are fitted with a 2.5A power supply.To satisfy the requirement of clause 6.4 of EN54-4 for fire alarm Power Supply Equipment mounted in a separate enclosure to the Control and Indicating Equipment a separate interface RPSM2 needs to be fitted inside the PSE enclosure which provides two transmission paths between the PSE and the CIE to enable one transmission path to continue to operate in the event of failure of the other. This board is fitted to models with the KD prefix to the part number. The D denoting that the dual output board is fitted.

GBP 553.48

1

Howler SH02 SafetyHub Fire Point

Howler SH02 SafetyHub Fire PointRaising the alert quickly in the event of a fire and having the appropriate equipment on hand to deal with it remains of utmost importance on every construction site. Be prepared and be proactive The SafetyHub FirePost sets the standard for effective site fire safety.ULTRA-TOUGH it stands out and stands upTIDY all the kit is in one neat unitPROTECTED ensures the equipment is always readyCOMPATIBLE with all Howler alarm systemsKey FeaturesRed signage backboard and statutory fire point signageFits any extinguisher type and size includes velcro strap retentionCompatible with any Howler fire alarm unitPlease note Additional shipping charges apply to this product.

GBP 481.00

1

Aritech ET010 Fibre-Glass Telescopic Pole - 4.5m

Aritech ET010 Fibre-Glass Telescopic Pole - 4.5mThe ET010 is a telescopic pole that is lightweight and quick and easy to extend to any height. It is used as an extension to the detector test equipment. This durable telescopic pole reach heights of up to 4.5m and may be extended using extension poles to reach up to 9 meters.These poles are subjected to rigorous conductivity testing to ensure the integrity of the insulating materials. Equipment in contact with live electrical components make it vital for the insulating materials to be of the highest standard. The ET010 will stand up to the rigours of every day use.Key FeaturesLightweight telescopic poleMaterial Fibre-glassNon-conductiveFor use with FG010

GBP 494.74

1

Howler SHR01 SafetyHub Fire Point cw Cabinet Signage and Siteplan Holder

Howler SHR01 SafetyHub Fire Point cw Cabinet Signage and Siteplan HolderRaising the alert quickly in the event of a fire and having the appropriate equipment on hand to deal with it remains of utmost importance on every construction site. Be prepared and be proactive The SafetyHub FirePost sets the standard for effective site fire safety.ULTRA-TOUGH it stands out and stands upTIDY all the kit is in one neat unitPROTECTED ensures the equipment is always readyCOMPATIBLE with all Howler alarm systemsKey FeaturesRed lockable extinguisher cabinetRed signage backboard and statutory fire point signageAdditional green backboard with A3 siteplan holder for exit route planFits any extinguisher type and sizeCompatible with any Howler fire alarm unitPlease note Additional shipping charges apply to this product.

GBP 994.09

1

Howler SHR0245 SafetyHub Fire Point cw Cabinet Wings Signage and Siteplan Holder

Howler SHR0245 SafetyHub Fire Point cw Cabinet Wings Signage and Siteplan HolderRaising the alert quickly in the event of a fire and having the appropriate equipment on hand to deal with itremains of utmost importance on every construction site. Be prepared and be proactive The SafetyHub FirePost sets the standard for effective site fire safety.ULTRA-TOUGH it stands out and stands upTIDY all the kit is in one neat unitPROTECTED ensures the equipment is always readyCOMPATIBLE with all Howler alarm systemsKey FeaturesTwo red wings for fire action notice fire assembly point information and fire extinguisher detailsRed lockable extinguisher cabinetRed signage backboard and statutory fire point signageAdditional green backboard with A3 siteplan holder for exit route planFits any extinguisher type and sizeCompatible with any Howler fire alarm unitPlease note Additional shipping charges apply to this product.

GBP 1132.12

1

Howler SHR08 SafetyHub Fire and Spill Point cw Cabinet Spill Module Signage and Alarm Backboard Excludes Alarm and Spill Kit

Howler SHR08 SafetyHub Fire and Spill Point cw Cabinet Spill Module Signage and Alarm Backboard Excludes Alarm and Spill KitRaising the alert quickly in the event of a fire and having the appropriate equipment on hand to deal with it remains of utmost importance on every construction site. Be prepared and be proactive The SafetyHub FirePost sets the standard for effective site fire safety.ULTRA-TOUGH it stands out and stands upTIDY all the kit is in one neat unitPROTECTED ensures the equipment is always readyCOMPATIBLE with all Howler alarm systemsKey FeaturesRed lockable extinguisher cabinetSpill canister for the storage of spill kitYellow signage backboard and statutory signage including fire action notice as shownFits any extinguisher type and sizeCompatible with any Howler fire alarm unitPlease note Additional shipping charges apply to this product.

GBP 1100.06

1

Advanced MxPro4 MXP-047 ESPA Pager Interface

Advanced MxPro4 MXP-047 ESPA Pager InterfaceThe MxPro Pager Interfaceis a programmable interface providing connectivity of the LifeLinePaging systems to the MxPro control equipment. It utilises the industry standard protocol ESPA 4.4.4 and connects to the equipment via a serial data connection.An optional input function is available to monitor pager fault conditions. Specific event types e.g. Fire Alarm Pre-Alarm Fault etc. can be sent to individual pagers and or to groups of pagers. In order to prevent radio paging systems in the UK causing interference systems must operate on an approved radio frequency issued by Ofcom.Ofcom licencing must be maintained at all times to comply with the given communication regulations.Key FeaturesESPA 4.4.4 ProtocolPanel Mounted or Boxed version3 Year Warranty as StandardMx-40005000 Series CompatibleEasily Configured via Pager PC Software

GBP 1061.39

1

Brand

Merchant

Price (EUR)