17 results (0,12957 seconds)

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Advanced MxPro4amp5 PC-NET-003-USB Series Configuration Software cw USB Lead

Kentec Syncro Net Fault Tolerant Network Interface Card - K555

Advanced MxPro5 MXP-503F Network Card - Standard Fitted

Advanced MxPro5 MXP-503F Network Card - Standard Fitted

Advanced MxPro5 MXP-503F Network Card - Standard FittedThe Ad-NeT network system allows all MxPro 5 series control panels remote terminals and network peripherals to be connected together using standard fire resistant two-core cable. It provides both the benefits of distributed intelligence and reduced installation costs whilst catering for the smallest two-panel network through to the largest 200 panel wide area networked system.The network operates as a true peer-to peer system allowing information from any input or output device to be passed over the network and displayed on any MxPro 5 control panel or remote terminal as required.Simply adding and connecting a network card allows any MxPro 5 control panel or remote terminal to be networked. All other nodes on the Ad-NeT system will be instantly aware of a panel as soon as it is given a valid network node address allowing additional panels to be added at any time. All panels incorporate a network analyser providing valuable diagnostic and status information and also have the facility to prevent the transmission of fires or faults during commissioning.For more complex systems the Windows based PC-NeT Mx configuration software allows sector based programming for Mute Silence Resound and Reset control keys as well as investigation delays group disablement and test instructions. All panels within the same sector will share common controls and each panel or remote terminal can also be programmed to show specific network information on a zonal basis. For cause and effect any input device can be programmed to operate any output device on any panel.Key FeaturesLarge Ad-NeT 200 Panel NetworkUp to 1.5Km between Control PanelsWindows based PC setupNetwork Systems share up to 1000 zonesNetwork Analysis from Control Panel

GBP 234.06
1

Advanced MXP-503 Standard Network Card MxPro5

Advanced MXP-503 Standard Network Card MxPro5

Advanced MXP-503 Standard Network Card MxPro5The Ad-NeT network system allows all MxPro5 series control panels remote terminals and network peripherals to be connected together using standard fire resistant two-core cable. It provides both the benefits of distributed intelligence and reduced installation costs whilst catering for the smallest two-panel network through to the largest 200 panel wide area networked system.The network operates as a true peer-to peer system allowing information from any input or output device to be passed over the network and displayed on any MxPro5 control panel or remote terminal as required.Simply adding and connecting a network card allows any MxPro5 control panel or remote terminal to be networked. All other nodes on the Ad-NeT system will be instantly aware of a panel as soon as it is given a valid network node address allowing additional panels to be added at any time. All panels incorporate a network analyser providing valuable diagnostic and status information and also have the facility to prevent the transmission of fires or faults during commissioning.For more complex systems the Windows based PC-NeT Mx configuration software allows sector-based programming for Mute Silence Resound and Reset control keys as well as investigation delays group disablement and test instructions. All panels within the same sector will share common controls and each panel or remote terminal can also be programmed to show specific network information on a zonal basis. For cause and effect any input device can be programmed to operate any output device on any panel.Key FeaturesLarge Ad-NeT 200 Panel NetworkUp to 1.5Km between Control PanelsWindows based PC setupNetwork Systems share up to 1000 zonesNetwork Analysis from Control PanelStandard NetworkThe maximum total cable length is 1.5km. The maximum number of network nodes is 32 50 with signal bufferFault Tolerant NetworkThe maximum cable length is 1.5km between each node and the maximum total loop length is 20km. Each network card has in-built diagnostics and is fully monitored for both short and open circuit faults between nodes. The network is capable of withstanding a single fault between nodes without loss of communications to any single panel. The maximum number of network nodes is 200.

GBP 234.06
1

C-Tec ZFP Multi-Path Fault Tolerant Network PCB

Advanced Programmable Relay - MXP-035

Advanced Mxp-003 Standard Network Card MXPro 4

Advanced MxPro 5 MXP-537F 10-way Switch Input Card Fitted

Advanced MxPro 5 MXP-537 P-BUS 10-Way Switch Input Card

Elmdene STX2410-E 24V d.c. PSU 27.6V 300W - Selectable LoadCharge Current 10A0.7A 8A1.6A 7.2A2.6A

Advanced MXP-034 Peripheral Bus - 4-Way Sounder Card

Advanced MxPro MXP-034F Peripheral Bus - 4-Way Sounder Card Fitted

Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card Fitted

ACT 612V Intelligent Battery Tester ACT612

ACT 612V Intelligent Battery Tester ACT612

ACT 612V Intelligent Battery Tester ACT612Simulates a full 20 hour battery discharge test in seconds. The ACT612 is a dual voltage intelligent battery tester designed for 6V and 12V lead acid batteries from 1.2Ah to 100Ah making it capable of testing 12V batteries up to 150Ah. Its the only product of its kind to have an Ampere-hour Ah calibration control enabling Ah readings to be adjusted to suit various battery technologies including standby SLA AGM cyclic GEL and car FLOODED WET batteries.The ACT612 contains advanced pulsed load analysis technology which removes surface charge to accurately measure the available Ah capacity based on the batterys temperature and state of charge. This enables you to check the voltage and test the capacity of new batteries straight from the box as well as used batteries which may show abnormal Ah capacity caused by excess temperature or from being under or overcharged.A table on the front of the meter indicates when batteries should be recharged or replaced due to age or operating conditions 65 of rated capacity. The ACT612 is designed for those who need to test different types of lead acid batteries quickly and easily.Key FeaturesTests 6V12V SLA GEL and Flooded lead acid batteriesSimulates a full 20 hour battery discharge test in secondsCapable of testing 12V batteries up to 150AhDisplays DC voltage and Ampere-hour Ah capacity available in the batteryAdvanced pulse load analysis accurately measures Ah capacity available in secondsAccurate Ah capacity based on batterys temperature and state of chargeUnique Ah Calibration Control enables standby SLA cyclic GEL and car FLOODED batteries to be testedUltra low heat generation allows continuous battery testingReverse polarity protection with LED warning indicationOver Voltage Protection to max 30VDC with LED warning indicationReplaceable plug-in test leadsHigh Impact ABS case with holsterCalibration Certification includedIdeal for those who need to test a broad range of lead acid batteries types in various applications such asfire and security systems UPS golf mobility and leisure etc.Technical InformationOperating Voltage 6V and 12V DCReverse Polarity Protection Red LED IndicationMax Input Voltage 15VDCOver Voltage Protection Max 30VDC 10 sec. with Red LED IndicationBattery Types SLA AGM GEL Flooded WETBattery Sizes 6V 1.2Ah 10Ah and 12V 1.2Ah to 100AhAh Capacity Test Simulated 20 hour C20 load test to 10.50VDCAh Calibration Calibrated at 0 zero position to brand new fully charged premium brand SLA batteries rated at C20 hour at 20C 68FAh Result Based on the battery under test temperature and state of chargeAdjustment Provides Ah adjustment to brand new fully charged standby SLA cyclic GEL and car FLOODED lead acid batteriesBattery Table Recharge or replace battery when Ah capacity available falls below 65 of the batterys stated capacityDisplay Type Blue Back-lit LCDFlat Battery Warning 6V 5.30VDC 12V 10.50VDCRepeat Test Operation Can perform repeat tests continuouslyDCV Accuracy 2 of displayed readingAh Accuracy 5 Fully charged premium brand C20 hour rated SLA batteries at 20 - 25C 68F - 77FApplied Pulse Load 6A 1.2Ah - 7Ah 18A 8Ah - 100AhAh Cal Adjustment Approx 25 dgtsCase Construction High impact ABS with holsterSize 84H x 170W x 41D mm including holsterWarranty 12 months RTBIN THE BOX ACT612 Intelligent Battery Tester ACT612TL Test Leads ACT430N Soft Carry Case Sample ACTBTL Labels Operating Instructions and Certificate of Calibration

GBP 258.72
1