ProfitSpring | B2B PPC Agency

Wagner AD-10-0550 Test Pipe For Air Sampling Systems

Wagner AD-10-0550 Test Pipe For Air Sampling SystemsA Test Pipe designed for Wagner Air Sampling Systems.

GBP 85.15

1

Ringtail X-CS3M LED Maintained Self-Testing Bulkhead IP65

Ringtail X-CS3M LED Maintained Self-Testing Bulkhead IP65The X-CS3M light is a high light output emergency bulkhead with the added benefit of utilising LEDs and a self-test facility. This LED bulkhead is a self-test emergency luminaire suitable for internal and external environments. It uses 6 high output LEDs with a moulded self-extinguishing polycarbonate base and fitted with a fresnel diffuser suitable for use on escape routes 850 degrees C Hot-wire test defined by ICEL.The diffuser is screw fixed and sealed by gasket to the base to provide IP65 protection. The gear tray is hinged and fully removable and cable entries are provided in the ends and base. This bulkhead can be fitted with a universal legend kit part no. ULK making it suitable for use as exit signs.Key FeaturesIP65PolycarbonateABS ConstructionClear Fresnel DiffuserRemovable Hinged Gear TrayExit SignsSelf-Test6 LEDsInternal External

GBP 55.91

1

Crowcon C01873 Gas Test Kit Magnet

Crowcon C01873 Gas Test Kit MagnetA Gas Test Kit Magnet replaces C01697 Crow mag key

GBP 46.66

1

International Gas Detectors 401101A Test Gas Applicator

International Gas Detectors 401101A Test Gas Applicator The 401101A is a test gas applicator for MK3 102 750 Series IGD ATEX Gas Detectors Fit 6 x 4mm ID Tube.

GBP 67.50

1

Gent S4-34899 Test Key for S4-34800 Range of MCP Pack of 25

Gent S4-34899 Test Key for S4-34800 Range of MCP Pack of 25The S4-34899 is a pack of call point keys for use with the new type Gent Vigilon Call Points.These keys allow the user to perform a test on a call point without breaking the glass in the unit. They also allow the front of the call point to be removed to allow access to the terminal connections within the call point.Key FeaturesPack of 25

GBP 45.01

1

C-Tec NC302RT Test Infrared Receiver

C-Tec NC302RT Test Infrared ReceiverThe NC302RT is a test infrared receiver to make fob testing simple. It is designed to be installed in a safe room or area. The fob to be tested is activated in this area. The LEDs of the tester will flash on successful activation but the system will not go into alarm.

GBP 77.92

1

Vesda WHTAST025I-10 25mm White Air Sampling Test Point PACK OF 10

Vesda WHTAST025I-10 25mm White Air Sampling Test Point PACK OF 10WHTAST025I-10 25mm White Air Sampling Test Point PACK OF 10

GBP 65.77

1

C-Tec QT302RT Quantec Test Infrared Ceiling Receiver

C-Tec QT302RT Quantec Test Infrared Ceiling ReceiverThe QT302RT is a test infrared receiver to make fob testing simple. It is designed to be installed in a safe room or area. The fob to be tested is activated in this area. The LEDs of the tester will flash on successful activation but the system will not go into alarm.

GBP 71.89

1

Vesda Xtralis 25mm White System Test Point PIP-018-W

Vesda Xtralis 25mm White System Test Point PIP-018-W Pack of 1025mm System Test Points are installed at the furthest point of the pipework and are used to introduce smoke in order to measure the time it takes for the smoke to reach the detectors. The maximum transport time is 120 seconds. They should always be connected withABS solvent cement.Key FeaturesMaterial ABSColour WhiteOperating temperature range -40C to 70CEN5425mmPack of 10Please note The PIP-018-W is equivalent to the WHTAST025I.

GBP 47.63

1

Crowcon M040119 Front Cover Seal Self-Adhesive

Crowcon M040119 Front Cover Seal Self-AdhesiveFront Cover Seal Self-Adhesive.Crowcon specialises in providing gas detection solutions for various industries and applications. As part of their product offerings Crowcon also provides an extensive range of spare parts and accessories specifically designed for their gas detection systems.

GBP 52.49

1

Morley ECO1000RTUA Remote LASER Tester for Vision Detectors

Morley ECO1000RTUA Remote LASER Tester for Vision DetectorsThe ECO1000RTUA is a Test Unit for Vision Detectors.The Laser remote tester can be used in conjunction with a wide range of ECO1000 series detectors. The device transmits a coded message which prevents false alarms generated by other devices using a laser. With a range of several meters the tester provides an easy way to test ECO1000 detectors and removes the need for direct physical access to the detector.Key FeaturesWireless remote test unit using laser beam for conventional ECO1000 series detectorsMaximum range 7m

GBP 52.33

1

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10Air sampling test points allow for functional smoke testing of aspirating smoke detection systems and are typically located at the end of a sampling pipe network.VESDA provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location. The room fabric often dictates the location of these capillary tubes. Hiding the capillary tubes behind light fittings blending in with ceiling paintings or forming part of the ceiling sculptures can all be used to provide invisible smoke detection.In high volume atria applications such as cathedrals capillary sample points can be routed into the area at intermediate vertical levels to good effect to overcome stratification. The higher potential sensitivity of the VESDA system means that less smoke is required at the sample points to provide an alarm condition.Key FeaturesOptimising performanceTough and durableChemical resistance propertiesCompatible with VESDA VESDA-E ICAM FAAST Airsense and SecuritonLightweightPack of 10Please note The PIP-018 is equivalent to the REDAST025I.

GBP 47.63

1

C-Tec BF430CEASR EA Wall Sounder Self-Testing Red

C-Tec BF430CEASR EA Wall Sounder Self-Testing RedA self-testing wall sounder designed for use with C-TECs CAST-powered EVAC-ALERT evacuation alert system.Key FeaturesDesigned for use on a C-TEC CAST-powered EVAC-ALERT systemSelf-testing functionality means access to a flat is only required when a fault is detectedEmits a clear concise and recognisable evacuation alarm toneImpressive 100dBA sound output at 1mLow 5.5mA alarm currentIP21C ratedComplies with EN54-3Reliable hard-wired technology

GBP 74.59

1

Vesda Xtralis 25mm Red ABS Self Draining Water Tap 02-WT-01

Vesda Xtralis 25mm Red ABS Self Draining Water Tap 02-WT-01A Self Draining Water Tap for mounting on pipes with a diameter of 25mm.It is designed to capture condensation in the pipes of the suction detector. Used in environments where such a phenomenon can occur.Please Note The 02-WT-01 is equivalent to the REDSDCT025I.

GBP 80.52

1

X-CS3 LED 230v Mains LED IP65 Bulkhead

X-CS3 LED 230v Mains LED IP65 BulkheadThe X-CSL3M light is a high light output emergency bulkhead with the added benefit of utilising LEDs and a self-test facility. This LED bulkhead is a self-test emergency luminaire suitable for internal and external environments. It uses 6 high output LEDs with a moulded self-extinguishing polycarbonate base and fitted with a fresnel diffuser suitable for use on escape routes 850 degrees C Hot-wire test defined by ICEL.The diffuser is screw fixed and sealed by gasket to the base to provide IP65 protection. The gear tray is hinged and fully removable and cable entries are provided in the ends and base. This bulkhead can be fitted with a universal legend kit part no. ULK making it suitable for use as exit signs.Key FeaturesIP65PolycarbonateABS ConstructionClear Fresnel DiffuserRemovable Hinged Gear TrayExit SignsSelf-Test6 LEDsInternal ExternalPlease Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting.

GBP 66.53

1

Solo Spare 1028 Aerosol Retaining Cup For Solo 330332 Dispenser

Solo Spare 1028 Aerosol Retaining Cup For Solo 330332 DispenserThe Solo Spare 1028 is a replacement Aerosol Retaining Cup which has been designed for use with the 330332 Smoke and CO Detector Test Dispenser.

GBP 52.13

1

Kidde DP721RT Dx700 Series Conventional Multisensor Fire Detector With Relay

Kidde DP721RT Dx700 Series Conventional Multisensor Fire Detector With RelayAll Aritech 700 series smoke detectors continuously monitor their sensitivity and operational status. Background drift is daily compensated to maintain the original calibrated sensitivity within the required limits.Once a day the detector performs a full diagnostic test that includes dynamically testing the sensing chamber and internal electronics. If a detector drifts out of sensitivity range or fails the internal diagnostics test this is reported back to the panel and indicated on the detector with a yellow fault LED.Maintenance friendly sensitivity level test modeThe 700 Series photoelectric detectors include a sensitivity test mode that may be activated by simply holding a magnet near the detectors test point. This initiates a self-diagnostic routine and provides visual indication if service is required. This test mode allows field sensitivity testing without the requirement for external meters or test gas.Field cleaning and serviceThe photoelectric sensing chamber unclips from the detector for easy field cleaning and service. During regular maintenance the detector cover can be removed the optical chamber removed and replaced by a low cost new chamber. On power up the detector auto-calibrates and returns to normal operating mode without any further intervention.The right detector for the right jobFor a truly fast and broad-spectrum detection the DP721RTA offers both optical and heat sensors. The interaction of both the smoke and heat algorithms ensure a quick response to both flaming and smouldering fires.All bases are provided with an integral locking tab for extra security if required. Bases are equipped with a shorting bar between IN and OUT that opens when the head is installed and that may be manually restored when removing the head. This simplifies cable continuity testing.Key FeaturesAutomatic self diagnostics with dynamic full detector and sensitivity testHigh false alarm immunity with floating background with drift compensationSeparate fire and fault LEDs for unambiguous alarm reportingWide operating voltage for use on most conventional systemsPolarity insensitive for carefree installationCOMNONC contacts for easy supervision on any systemManual self diagnostic with visual sensitivity indicationField exchangeable and disposable optical chamber

GBP 46.97

1

C-Tec BF430CEASW EA Wall Sounder - Self Testing - White

C-Tec BF430CEASW EA Wall Sounder - Self Testing - WhiteThe BF430CEASW is a new EN54-3 compliant evacuation alert system from C-TEC specifically designed to assist the fire rescue services FRS in evacuating high-rise residential buildings. The device offers low current consumption emitting a clear concise and recognisable evacuation alarm tone.Details Designed for use on a C-TEC CAST-powered EVAC-ALERT system Self-testing functionality means access to a flat is only required when a fault is detected Emits a clear concise and recognisable evacuation alarm tone Impressive 100dBA sound output at 1m Low 5.5mA alarm current IP21C rated. Complies with EN54-3 Red version also available order code BF430CEASR

GBP 74.59

1

Testifire XTR2 TESTIFIRE-MEML-001 Membrane for USA amp Middle East Regions

Testifire XTR2 TESTIFIRE-MEML-001 Membrane for USA Middle East RegionsTestifire XTR2 is the next generation of our popular Testifire product however it is much more than just a functional test tool. Testifire XTR2 has compliance at its core its unique features enable compliant testing to be carried out and via an App and supporting cloud-portal ensure test results can be recorded automatically at the time of test giving fire service managers and building owners the ultimate proof of test.Whats in the reportThe test report is automatically generated on-site once the final detector has been tested. Its then immediately available for viewing by the relevant team members at the service company and then be sent to the client along with any other relevant documentation. The report combines all the data needed to prove testing has taken place and confirms the status of each detector automatically highlighting any areas of concern at the top of the document.Key FeaturesSpecialist membrane allowing use of Testifire XTR2 with larger detectors

GBP 45.65

1

Emergency Lighting X-ES3SL24 LED Slave Exit Box 24V ACDC

Emergency Lighting X-ES3SL24 LED Slave Exit Box 24V ACDCThe X-ES3 is a general purpose LED escape route exit sign that is switchable MaintainedNon-maintained self-contained. Designed to be wall mounted Self-contained.It is available in LED Self-Test DALI Addressable and Wireless Communication.Central Battery slave units in 24v 50v 110v and 230v ACDC Static Inverters.Hold off Relay White finish as standard Chrome Satin Chrome Brass and Black finishes available. Cinema Legend Black Legend option.

GBP 79.92

1

Apollo Intelligent Open Area Red Sounder Sonos - 55000-001APO

Apollo Intelligent Open Area Red Sounder Sonos - 55000-001APOThe Intelligent Open-Area Sounder has beendesigned for use in open areas and can be connected to any Discovery or XP95 system.Key Features Self-test fault monitoringChoice of tones on standard device Apollo Slow Whoop and DINTwo volume settings 92dBA and 100dBASynchronisation of tonesIndividual and group addressingBuilt in isolatorRed or white optionsLoop-poweredIP65 rated

GBP 44.81

1

Apollo Intelligent Red Open-Area Sounder Beacon - 55000-005APO

Apollo Intelligent Red Open-Area Sounder Beacon - 55000-005APOThe Intelligent Open-Area Sounder Visual Indicator is designed for use in open areas and can be connected to an Apollo Discovery or XP95 system.Key Features Self-test monitoringChoice of tones on standard device Apollo Slow Whoop and DINTwo volume settings 92dBA and 100dBAIndividual and group addressingSynchronisation of tones and flashesBuilt in isolatorLoop-poweredIP65 ratedRed and clear lens options

GBP 69.17

1

X-ERS LED 230v Mains Square Weatherproof Luminaire

X-ERS LED 230v Mains Square Weatherproof LuminaireA quality decorative luminaire designed for use by architects and designers. Comprising of a moulded self-extinguishing polycarbonate base fitted with a clear diffuser suitable for use on escape routes. The X-ERS Light offers a cost-effective emergency lighting and mains lighting combination and is ideal for areas where higher light levels are required.Key FeaturesHigh lumen outputLow power consumption4000k Colour temperatureIP65DALI and Self-Test optionsCentral Battery and Static inverter systemsBlack base finish optionPlease Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting.

GBP 87.05

1

Apollo 45681-330APO Intelligent Sounder Visual Indicator Base with Isolator

Apollo 45681-330APO Intelligent Sounder Visual Indicator Base with IsolatorThe low volume range is useful in areas such as hospitals where a fire alert is initially intended to warn staff only. The sounder is set to the high range for general use. Synchronisation of tones ensures the integrity of the signaltones from different sounders do not merge into one signal that could be mistaken for a different tone. Group addressing is a simple method of alerting an entire area or group of rooms without delay.For systems requiring isolators at every point the built-in isolator saves installation time and cost. The acoustic self-test means that the sounder listens to itself when it is switched on. If no sound is detected a fault signal is transmitted when the sounder is polled.The beacon self-test is achieved by means of an LED monitoring circuit. If the LEDs do not draw current when the sounder beacon base has been switched on a fault signal is transmitted when the device is next polled.Key FeaturesTwo volume ranges 55-75dBA and 75-91dBAVisual indicator flash rate of once per secondSynchronisation of alert and evacuate tonesSynchronisation of visual indicator flashIndividual and group addressingUnique acoustic and visual indicator self-testBuilt-in Isolator

GBP 58.67

1

X-MPR LED 3 Hour Maintained Blade Exit Sign

X-MPR LED 3 Hour Maintained Blade Exit SignA compact recessed exit sign.TheX-MPRis a decorative illuminated escape route and direction sign light. Using high illumination white LEDs in a small compact shell with self-test facility. It is designed to be recess mounted in ceilings allowing escape route lighting to be provided in a low profile.Comprising of a stove enamelled sheet steel base fitted with a white bezel suitable for use on escape routes 850 degrees C Hot-wire test defined by ICEL. The bezel is attached by captive screws and provides a seal to IP20. The gear tray is hinged for ease of installation and is easily removable to allow first fix of the base.Key FeaturesRecess mount escape route signHigh output LED light sourceIP20Many alternative finishes availableChoice of LegendSelf contained

GBP 82.86

1

Brand

Merchant

Price (EUR)