2.642 results (0,16473 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10

Vesda Xtralis 25mm Air Sampling Test Point - Pack of 10Air sampling test points allow for functional smoke testing of aspirating smoke detection systems and are typically located at the end of a sampling pipe network.VESDA provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location. The room fabric often dictates the location of these capillary tubes. Hiding the capillary tubes behind light fittings blending in with ceiling paintings or forming part of the ceiling sculptures can all be used to provide invisible smoke detection.In high volume atria applications such as cathedrals capillary sample points can be routed into the area at intermediate vertical levels to good effect to overcome stratification. The higher potential sensitivity of the VESDA system means that less smoke is required at the sample points to provide an alarm condition.Key FeaturesOptimising performanceTough and durableChemical resistance propertiesCompatible with VESDA VESDA-E ICAM FAAST Airsense and SecuritonLightweightPack of 10Please note The PIP-018 is equivalent to the REDAST025I.

GBP 47.63
1

Vesda Xtralis 25mm White System Test Point PIP-018-W

Vesda Xtralis 25mm White System Test Point PIP-018-W

Vesda Xtralis 25mm White System Test Point PIP-018-W Pack of 1025mm System Test Points are installed at the furthest point of the pipework and are used to introduce smoke in order to measure the time it takes for the smoke to reach the detectors. The maximum transport time is 120 seconds. They should always be connected withABS solvent cement.Key FeaturesMaterial ABSColour WhiteOperating temperature range -40C to 70CEN5425mmPack of 10Please note The PIP-018-W is equivalent to the WHTAST025I.

GBP 47.63
1

Carrier I-9403 Intelligent SounderVisual Indicator - 24VDC

Carrier I-9403 Intelligent SounderVisual Indicator - 24VDC

Carrier I-9403 Intelligent SounderVisual Indicator - 24VDCI-9403 Intelligent Sounder Strobe is an audible and visual alarm device installed in field which can be activated by fire alarm control panel in fire control centre. After activated it will generate strong audible and visual alarm signal to warn people in field.A 25.5mm high shallow base and a 40mm high deep base are available. The sounder strobe comes with the shallow base. The deep base C-94DB should be ordered separately.Key FeaturesProviding 16 tonesUsing ultra bright LEDs as source for light indicationOptional transparent colourless lens C-94WL availableLoop powered or external 24V poweredPower-saving consumption mode and normal consumption mode factory defaultSingledual address programmableWorking modes sounder strobe strobe only sounder onlyStandard EN 54-3

GBP 48.52
1

Morley ECO1000RTUA Remote LASER Tester for Vision Detectors

Morley ECO1000RTUA Remote LASER Tester for Vision Detectors

Morley ECO1000RTUA Remote LASER Tester for Vision DetectorsThe ECO1000RTUA is a Test Unit for Vision Detectors.The Laser remote tester can be used in conjunction with a wide range of ECO1000 series detectors. The device transmits a coded message which prevents false alarms generated by other devices using a laser. With a range of several meters the tester provides an easy way to test ECO1000 detectors and removes the need for direct physical access to the detector.Key FeaturesWireless remote test unit using laser beam for conventional ECO1000 series detectorsMaximum range 7m

GBP 52.33
1

Ziton Horn Sounder with Dual Front amp Rear Sound Paths 102 dBA - Polar White

Ziton Horn Sounder with Dual Front amp Rear Sound Paths 102 dBA - Polar White

Ziton Horn Sounder with Dual Front Rear Sound Paths 102 dBA - Polar WhiteZP755HA-2P is a POLAR WHITE addressable horn sounder designed for use with ZP addressable fire alarm systems. Designed with dual front and rear sound paths it provides an all around sound output - ideal for open area coverage.Installed directly onto and powered by the ZP wiring loop the ZP755HA-2 sounders enable the system designer to offer a complete ZP addressable system on a single pair of wires. Installation time and costs are further reduced as the moulding plugs directly into a first fix base eliminating the need for any internal connections.The units high efficiency acoustic design together with a low energy sound gun transducer enables up to 40 sounders to be connected to a one kilometre loop of 1.5mm cable with a wiring run of 50 metres to the first device.Self test facilityThe range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive ZP755 sounders can be powered directly from an external power supply. All ZP755 sounders incorporate switch settings enabling them to be assigned a unique address which is polled by the panel every two seconds.Range of sound outputsContinuous intermittent and two-tone outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. Sound types comply with most international codes e.g. BS 5839 Part 1 recommended frequencies.ZP755HA-2 sounders produce a sound output of up to 92 dBA tested at 1 metre. The volume setting can be reduced for areas where a lower sound output is required.Moulded in high impact thermoplastic the sounders are available in either polar white red or white.Key FeaturesWide all around sound distributionMicrophone self test facilityPlug in base no internal connectionsUp to 40 sounders directly on the loop wiringHigh efficiency sound gun transducerSynchronised outputs

GBP 60.88
1

Ziton ZP755HA-2R Horn Sounder Red

Ziton ZP755HA-2R Horn Sounder Red

Ziton ZP755HA-2R Horn Sounder RedZP755HA-2R is a RED addressable horn sounder designed for use with ZP addressable fire alarm systems. Designed with dual front and rear sound paths it provides an all around sound output - ideal for open area coverage.Installed directly onto and powered by the ZP wiring loop the ZP755HA-2 sounders enable the system designer to offer a complete ZP addressable system on a single pair of wires. Installation time and costs are further reduced as the moulding plugs directly into a first fix base eliminating the need for any internal connections.The units high efficiency acoustic design together with a low energy sound gun transducer enables up to 40 sounders to be connected to a one kilometre loop of 1.5mm cable with a wiring run of 50 metres to the first device.Self test facilityThe range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive ZP755 sounders can be powered directly from an external power supply. All ZP755 sounders incorporate switch settings enabling them to be assigned a unique address which is polled by the panel every two seconds.Range of sound outputsContinuous intermittent and two-tone outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. Sound types comply with most international codes e.g. BS 5839 Part 1 recommended frequencies.ZP755HA-2 sounders produce a sound output of up to 92 dBA tested at 1 metre. The volume setting can be reduced for areas where a lower sound output is required.Moulded in high impact thermoplastic the sounders are available in either polar white red or white.Key FeaturesWide all around sound distributionMicrophone self test facilityPlug in base no direct wiring connectionsUp to 50 sounders directly on the loop wiringHigh efficiency sound gun transducerSynchronised outputsEN543 approved and CPR certified

GBP 62.54
1

Morley IAS MI-WSO-PP-I Wall Mounted White Sounder with Loop Isolation

Morley IAS MI-WSO-PP-I Wall Mounted White Sounder with Loop Isolation

Morley IAS MI-WSO-PP-I Wall Mounted White Sounder with Loop IsolationWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APMorley IAS Protocol32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 49.34
1

Morley MI-BRS-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base Standard cw Isolator

Morley MI-BRS-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base Standard cw Isolator

Morley MI-BRS-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base Standard cw IsolatorThe MI-BRS-PC-I Detector Base Standard performance Sounder Strobe is a modular high-output loop powered device intended to alert building occupants of a potential fire. Approved to EN54-3 EN54-17 EN54-23 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.Key FeaturesGlobal approved 32 tone set selectable from device or from panelAutomatic synchronization of sounder and strobeMaximum light sound output with efficient power consumption enables more devices on a loopPremium device with high light coverage reduces wiring pointsSingle point of installation - saves time cost inventoryLarge cable access rear or surface cable entryAdjustable sound light tones to suit varying installation applicationsRotary wheels address tags for clear address indicationMeets detector spacing thereby reducing requirement for additional strobe devicesFewer wiring points for cost effective installation and simplified system maintenanceModular design allows individual components to be replaced separately

GBP 53.04
1

Ziton ZP755R-2 Addressable Room Sounder

Ziton ZP755R-2 Addressable Room Sounder

Ziton ZP755R-2 Addressable Room SounderThe ZP755R-2R is a RED addressable loop powered room sounder or us on ZP fire alarm systems. The ZP755R-2R combines a detector base and audible sounder in a single stylish moulding.The ZP755R-2R is developed for applications in individual rooms sleeping accommodation or small compartments where it is impractical or unnecessary for the sounder and detector to be combined. Installed directly onto a ZP7 wiring loop - the ZP755R-2R enables the system designer to offer a complete addressable system on a single pair of wires. Installation costs are greatly reduced whilst system integrity sounder options and programmed alarm organisation are significantly increased. Time on site is further reduced as the moulding plugs directly into a first fix base eliminating the need for any wiring directly to the device.Advanced acoustic designHigh efficiency acoustic design and a low energy sound gun transducer enable combinations of up to 60 sensors and 60 sounders to be connected to a 1km loop of 1.5mm cable. In systems where loop lengths or current requirements are excessive the ZP755R-2R sounders can be locally powered from an external power supply.Output Test and Tone SelectionThe ZP755 range of notification devices features a unique self-test facility which is automatically activated during routine sounder testing. A built in microphone circuit measures sound output level and automatically signals the sounder address and location to the control panel should the output test fail.Continuous intermittent and two-tone outputs are available from which any combination can be chosen to provide alert and evacuate for two stage alarms. Sound types comply with most international codes e.g. BS 5839 Part 1 recommended frequencies. The ZP755R-2R features a sound output of up to 90dBA and a volume control for areas where a reduced sound output is required.Key FeaturesPowered directly from the ZP loopUp to 60 detectors and 60 sounders directly on the loop wiringPlug in base no direct wiring connectionsHigh efficiency sound gun transducerWide range of international sound types and frequenciesEN543 Approved and CPR certifiedFor this product in White please use the ZP755B Sounder Base with a ZP755-COV-P Base Cover.

GBP 57.60
1

Morley MI-BRH-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base High Performance Sounder Strobe cw Isolator

Morley MI-BRH-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base High Performance Sounder Strobe cw Isolator

Morley MI-BRH-PC-I Red Flash Pure White Body Clear Lens Intelligent Detector Base High Performance Sounder Strobe cw IsolatorThe MI-BRH-PC-I Detector Base High performance Sounder Strobe is a modular high-output loop powered device intended to alert building occupants of a potential fire. Approved to EN54-3 EN54-17 EN54-23 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.Key FeaturesGlobal approved 32 tone set selectable from device or from panelAutomatic synchronization of sounder and strobeMaximum light sound output with efficient power consumption enables more devices on a loopPremium device with high light coverage reduces wiring pointsSingle point of installation - saves time cost inventoryLarge cable access rear or surface cable entryAdjustable sound light tones to suit varying installation applicationsRotary wheels address tags for clear address indicationMeets detector spacing thereby reducing requirement for additional strobe devicesFewer wiring points for cost effective installation and simplified system maintenanceModular design allows individual components to be replaced separately

GBP 64.78
1

Apollo Intelligent Open-Area Clear Beacon - 55000-010APO

Apollo Intelligent Open-Area Clear Beacon - 55000-010APO

Apollo Intelligent Open-Area Clear Beacon - 55000-010APOThe Intelligent Open-Area Visual Indicator has been developed for use in situations where there is a risk that sounders will not be heard.All devices are powered directly from the loop and need no external power supply. They operate at 1728V DC and are polarity sensitive.All the alarm devices can be assigned group addresses as well as individual addresses so that the functional options of the sounder are identical with those of the Sounder Control Unit.Key FeaturesFor use with XP95 Discovery systemsSelf-test fault monitoringIP65 ratedIndividual and group addressingSynchronisation of flashes Comes with Isolating Base as standardLoop-powered

GBP 45.98
1

Morley IAS MI-BSO-PP-I Addressable Base Sounder with Loop Isolation BSO-PP-I05

Morley IAS MI-BSO-PP-I Addressable Base Sounder with Loop Isolation BSO-PP-I05

Morley IAS MI-BSO-PP-I Addressable Base Sounder with Loop Isolation BSO-PP-I05Base sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the B501AP base for improved installation flexibility and integrates seamlessly. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APMorley IAS Protocol32 tone selection to cover many markets on device or from panel

GBP 49.45
1

Advanced TOUCH-10-SBB Touch-Screen Terminal - Surface Back Box

Advanced TOUCH-10-SBB Touch-Screen Terminal - Surface Back Box

Advanced TOUCH-10-SBB Touch-Screen Terminal - Surface Back BoxTouchControl is a 10 high-resolution touch screen Remote Control Terminal with active maps and zone plans.It is a fire panel and network node in its own right and works on Advanceds standard and fault tolerant networks. It is compatible with our MxPro and Axis EN fire panels.Zone information is presented via both the units colour coded easy-to-navigate interface and the active maps that are easily configured using the Dynamix Tools Map App.Using TouchControls colour-coded easy-to-navigate interface users canEvacuateMuteSilenceResound ResetView fires faults disablements alarms inputs outputs supervisory and network via instant filtersViewenabledisable zonesViewenabledisable devicesEnabledisable outputs by typeEnable Walk Test modeTest displayzonesoutputsbuzzer and LEDsQuickly access all zones in firefaultdisablementtest via instant filters and where allowed change statusView 1000 general and 500 Fire event logSet network time and dateUsers can choose from five pre-set background images or upload their own. The relevant zone plan to the units position can be displayed and users can run presentations on the display which defaults to normal operation in the event of a fire condition or if the screen is touched. TouchControl enhances public areas and provides new levels of control and oversight.Key Features2 Part enclosure for easy first fix and slide-in installation.10 high resolution screen designed to work with firemans glove At a glance system status immediately identify zones and devices in Fire Test Supervisory and FaultInteractive site maps and zone plans capability built-inMonitored external input for external PSU faultsTwo-core connection to the network fault tolerant or standardLow-profile bezel for flush fittingSelect from a number of background images or add a customised imageLow profile installationDedicated status indicators for Fire Fault System Fault Disabled Test and Power Zone plan display an essential part of BS5839-1Dual Power Supply inputs independently monitored to allow redundant power feeds

GBP 74.14
1

Ziton ZP886W ZP7 Addressable Manual Call Point White

Ziton ZP886W ZP7 Addressable Manual Call Point White

Ziton ZP886W ZP7 Addressable Manual Call Point WhiteThe Ziton ZP886W is a white single action addressable indoor manual call point. It is delivered complete with resettable element test connector and test key. Multiple optional accessories are available to facilitate most indoor installation requirements.This single action MCP is a standard profile indoor MCP suitable for surface and recess mount installations using standard or legacy European electrical boxes. With its designer dual tricolour LEDs it offers 180 clear local indication of its operational status even from a side view in a passage installation. The clean face of the MCP is further enhanced by a front access and test key facility.CompatibilityThe ZP880 range may be used on compatible Ziton fire systems. They can be deployed seamlessly into existing legacy systems without CIE configuration changes.Installation and maintenance friendlyThe front-facing access for an aesthetically matching test key allows unhindered access regardless of the installation location. The MCP key doubles as a test and disassembly tool allowing removal of the MCP front cover without the need for additional tools.Key FeaturesReliable single action manual call point for surface mountingA dual tri-colour status indicator offers 180 alarm visibilityTamper resistant design with resettable or frangible elementStandard mounting options facilitates easy retrofitting to existing installationsUnobtrusive front facing test facilityMatching back box with rear top and bottom cable entryScreen connection terminal for electrically noisy installationsPluggable connector with link through facility for ease of installation and pre-commissioning testingAlarm flag on the face of the MCP allows alarm indication even without alarm LEDsFast no-tools-required maintenance using the test keyUp to 127 devices per loop

GBP 74.71
1

Morley MI-WSS-PR-I Wall Mounted Sounder VID Red Body Red Flash with Loop Isolation

Morley MI-WSS-PR-I Wall Mounted Sounder VID Red Body Red Flash with Loop Isolation

Morley IAS MI-WSS-PR-I Wall Mounted Sounder VID Red Body Red Flash with Loop IsolationIt utilises the B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder and intense strobe give a visible and audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessEN54-3 approvedRear or surface cable entryLoop continuity springAutomatic synchronisation of sounder and strobeCommon base with detectors B501APMorley IAS Protocol32 tone selection to cover many markets on device or from panelPositive poke yoke engagementAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controlsPlease Note this product is now approved to EN54-23 VAD and must not be used as a visual alarm device to provide a primary warning notification of fire.

GBP 74.48
1

Apollo Discovery CO Heat Multisensor 58000-305APO

Apollo Discovery CO Heat Multisensor 58000-305APO

Apollo Discovery CO Heat Multisensor 58000-305APOThe Discovery COHeat Multisensor Detector is good at detecting deep-seated smouldering fires which give off a lot of CO as well as flaming fires. They are ideal for use in hotel bedrooms where steam may bepresent dusty environments or even where simulated smoke may bepresent.The Discovery COHeat Multisensor Detector contains a CO detection cell and a thermistor temperature sensor whose outputs are combined to give the final analogue value. The way in which the signals from the two sensors are combined depends on the response mode selected. The COHeat Multisensor detects the presence of carbon monoxide or heat or a combination of both. The Multisensor construction is similar to that of a CO detector but uses a different lid in order to expose the thermistor to the surrounding air. The signals from the CO sensing cell and the thermistor are independent and represent the amount of CO or the temperature present in the vicinity of the detector. When the detector is used in heat only mode Mode 5 it operates as an A1R rate-of-rise heat detector with a static threshold of 58C.Brand InformationDiscovery is a range of high-specification analogue addressable fire detectors and alarm devices. Discovery detectors offer effective false alarm management by a combination of EN 54 approved operating modes and sophisticated algorithms. Drift compensation further reduces the likelihood of false alarms caused by a build-up of dust in the sensing chamber.In addition to the familiar smoke and heat detectors the Discovery range features two multisensor detectors. One is an opticalheat multisensor which can be used to protect against many types of fire risk. The other is a carbon monoxideheat multisensor which protects against both smouldering fires and those generating heat.Operating PrinciplesDiscovery detectors are designed to be operated with purpose-designed control and indicating equipment that makes full use of their features. Discovery can however be connected to any fire control panel which can operate existing ranges of Apollo analogue addressable detectors with the previously noted rule that the control and indicating equipment must not have a drift algorithm operating on Discovery devices. Contact the fire control panel manufacturer for guidance.Maintenance ServiceDetectors should be maintained according to BS 5839- or other locally applicable code. Test equipment can be ordered from us which can test smoke and heat detectors.Key Features Responds to smouldering and flaming firesLess susceptible to false alarms caused by steam and dustFive response modesRemote test feature

GBP 77.17
1